
Open-source KiCad boards
66 match “BMP18”Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.
- 2 layers17.8 × 19.2 mm

- 2 layers17.8 × 17.8 mm

Adafruit adafruit bmp183 breakout pcb adafruit bmp183 breakout
oomlout/oomlout_oomp_project_bot_v_2
16 parts - 2 layers61 × 61 mm

ESP32 FC
MAATHES-THILAK-K/ESP32-S3_FLIGHT_CONTROLLER
A custom-designed flight controller based on the ESP32-S3 module, built for compatibility with the esp-fc firmware and Betaflight-like configuration.
69 parts7Apache-2.0 - 2 layers61 × 61 mm

- 4 layers85 × 60 mm

- 2 layers65 × 31 mm

- 2 layers98 × 83.8 mm

Projeto placa
phfbertoleti/placa_lorawan
Repositório oficial da placa LoRaWAN, um kit de desenvolvimento para protótipos IoT.
39 parts19MIT - 2 layers86.5 × 59.7 mm

- 2 layers93 × 42 mm

ADEM
timelab/ADEM
Mobile device for distributed measurements of particulate matter (fine dust)
29 parts13LGPL-3.0 - 2 layers47.9 × 49.6 mm

BMP280Tiny
danheeks/vario
paragliding vario with arduino nano, piezo sounder, bmp180 altimeter, 4x Nimh batterys
45 parts11 - 2 layers55.5 × 21.9 mm

- 2 layers96 × 89.9 mm

ATmega SAT
spel-uchile/balloon_experiment
Radiosonde platform to develop, test and integrate payloads for the future CubeSats missions
67 parts6 - 2 layers

- 2 layers58.4 × 74.7 mm

Placa manutencao preventiva
phfbertoleti/placa_monitoramento_lorawan
Placa - Monitoramento LoRaWAN
23 parts4MIT - 2 layers76 × 65 mm

- 6 layers95.9 × 90.2 mm

PHAT-3-Main Board
UWCubeSat/PHAT-3-Main-Board
PCB design for the PHAT-3 weather balloon payload's main board, housing a radio, sensors, camera, and buck converter.
34 parts3 - 2 layers59.5 × 69.5 mm

Zenith
NateOrlowski06/Zenith
A high powered rocketry dual deploy recovery device and data logger.
16 parts2 - 2 layers81 × 72.8 mm

GPS INS PCB
siddarthiyer/GPS-aided-Inertial-Navigation-System-Module
Upper 6 bits - Module ID - max 0x3F Lower 5 bits - Command ID - max 0x1F CAN ID = (Module ID Default Module ID : 0x200 (Standard)
29 parts2 - 2 layers76.7 × 35.1 mm

Weather station
VincentKobz/diy-weather-station
The goal is to build from scratch a small intelligent weather station that can be connected to IOT networks.
14 parts2MIT - 2 layers52.7 × 55.2 mm

Homepost
CeSiumUA/homepost
A simple IoT project that integrates with HomeAssistant and involves phone presence tracking, temperature/humidity (pressure and others in future) and radiation level measurement
18 parts1 - 2 layers128.1 × 128.1 mm

- 4 layers94 × 28 mm

Lux
Erox-02/Luxion
Luxion is a custom made drone made with rust unlike standard c++ drones . It uses a custom pcb, ESP32-S3-WROOM-1U , MPU6500-IMU(breakout as it costs less than the bare), four motor drivers, and a 1S LiPo to power the…
50 parts1GPL-3.0 - 2 layers76 × 75 mm

- 2 layers

Rpi2HAT for ver3
jacekidziak/RPI_DRON_HAT
Project of PCB with servo driver, battery voltage measurement, IMU, GPS and barometr
77 parts1