Skip to the content

PCB

2,721 boards

KiCad boards from 1,297 GitHub repositories tagged “pcb”, the most starred first; open any of them in PCBKit.

  • 2 layers42 × 78 mmP.003-V1.0.1, the printed circuit board in 3D

    P.003-V1.0.1

    GSAS-LABS/P.003

    Digital dice based on an ATtiny85 and 74HC595. Supports D4, D6, D8, and D10 modes, with configurable rolling animation, button-based type selection, EEPROM persistence, and low-power sleep mode for extended battery life.

    21 partsCERN-OHL-S-2.0
  • 4 layers49.5 × 21.6 mmUSB Replug Dongle RevC1, the printed circuit board in 3D

    USB Replug Dongle RevC1

    gslee-dev/portpulse

    USB replug test dongle with KiCad hardware, CH552 firmware, and native C host

    38 partsMIT
  • 2 layers26.3 × 18 mmMax30102 pcb, the printed circuit board in 3D

    Max30102 pcb

    Habib-creater/MAX30102_Optical_Sensor_Board

    MAX30102-based optical sensor board designed for embedded hardware development.

    18 parts
  • 4 layers60 × 50 mmMdrv, the printed circuit board in 3D

    Mdrv

    hanneskiene/mdrv

    Mcu controlled three phase motor driver with PPM input

    112 partsMIT
  • 2 layers97.9 × 113.9 mm555 demo, the printed circuit board in 3D

    555 demo

    harrisoncbrammell/555friend

    A PCB designed to introduce 555 timers and their three operating states.

    44 parts
  • 2 layers79 × 122.4 mmTeensy macro pad, the printed circuit board in 3D

    Teensy macro pad

    HarryCutts/twentypad

    A simple twenty-key macro pad based on the ATMEGA32

    54 parts
  • 4 layers135 × 101.3 mmNft hydroponic controller, the printed circuit board in 3D

    Nft hydroponic controller

    hasan-abuzaid/nft-hydroponic-controller

    Open-hardware ESP32-S3 controller for NFT hydroponics: pH/EC/level sensing, 6 relay channels, ESPHome + Home Assistant

    107 partsCERN-OHL-S-2.0
  • 2 layers48 × 36 mmFault strapping pin, the printed circuit board in 3D

    Fault strapping pin

    hash066/siliconsmith

    Agents that design hardware, and prove it. Prompt-first workstation (Matter, Board, Silicon) on Nemotron + Nebius Token Factory and Sandboxes. Open-source pip package, CLI and MCP server. Live demo, no sign-up.

    21 partsApache-2.0
  • 2 layers144 × 80 mmDCDCPCB, the printed circuit board in 3D

    DCDCPCB

    henrysg1/solar-car-dcdc

    This repository contains the KiCAD project for the University of Nottingham's solar race car DCDC converter.

    31 partsMIT
  • 2 layers50.6 × 62.2 mmAir ghost, the printed circuit board in 3D

    Air ghost

    HeyPCB/air-ghost

    Air Ghost: A little ghost that blushes red when your room needs fresh air. KiCad 10, heypcb.ai merch.

    19 partsCERN-OHL-S-2.0
  • 2 layers63.2 × 85 mmBadge blob, the printed circuit board in 3D

    Badge blob

    HeyPCB/badge-blob

    Blob, the social battery badge: The name badge that tells people whether to come say hi. KiCad 10, heypcb.ai merch.

    18 partsCERN-OHL-S-2.0
  • 2 layers40 × 96.1 mmCable bunny, the printed circuit board in 3D

    Cable bunny

    HeyPCB/cable-bunny

    Cable Bunny: Is it a charge-only cable? Ask the bunny. KiCad 10, heypcb.ai merch.

    25 partsCERN-OHL-S-2.0
  • 4 layers31 × 64 mmEsp32-s3-devkit, the printed circuit board in 3D

    Esp32-s3-devkit

    HeyPCB/esp32-s3-devkit

    ESP32-S3 dev board in the DevKitC-1 layout (31 x 64 mm, 4 layers, KiCad 10), built through HeyPCB's MCP server

    30 partsMIT
  • 2 layers42 × 53.2 mmFridge owl, the printed circuit board in 3D

    Fridge owl

    HeyPCB/fridge-owl

    Hoot, the fridge reminder owl: The fridge owl that blinks at you until you've taken your meds and had your water. KiCad 10, heypcb.ai merch.

    13 partsCERN-OHL-S-2.0
  • 2 layers112 × 158 mmHello, the printed circuit board in 3D

    Hello

    HeyPCB/hello-8051

    HELLO: a tiny 8051 computer shaped like a 1984 desktop. AT89S52, 32 KB SRAM, 128x64 ST7920 LCD, USB-C. 112 x 158 mm 2-layer KiCad 10 board, DRC clean, firmware that writes hello. Built through HeyPCB's MCP server.

    27 partsMIT
  • 4 layers64 × 80 mmIris brainstem, the printed circuit board in 3D

    Iris brainstem

    HeyPCB/iris-brainstem

    Iris Brainstem: power and servo hub of the Iris robot head. 9 V USB-C PD in, 6 V / 5 A servo rail in stitched copper zones (measured), 5 V rail, half-duplex servo bus with ten ports, speaker amp.

    97 partsCERN-OHL-S-2.0
  • 2 layers116 × 12 mmIris brow, the printed circuit board in 3D

    Iris brow

    HeyPCB/iris-brow

    Iris Brow: forehead sensor strip of the Iris robot head. VL53L1X distance, APDS-9306 light, two I2S microphones 108 mm apart, touch pads, on a brow-shaped board. 2-layer KiCad 10 board, DRC-clean, fab-ready.

    20 partsCERN-OHL-S-2.0
  • 4 layers80 × 40 mmIris cortex, the printed circuit board in 3D

    Iris cortex

    HeyPCB/iris-cortex

    Iris Cortex: head controller of the Iris robot head. ESP32-S3 (16 MB flash, 8 MB PSRAM), OV2640 eye-camera FPC, iris-ring LED drivers, harness hub.

    77 partsCERN-OHL-S-2.0
  • 2 layers18 × 17.4 mmIris ring, the printed circuit board in 3D

    Iris ring

    HeyPCB/iris-ring

    Iris Ring: the 18 mm annular LED board behind each iris of the Iris robot head. 12 WS2812-2020 pixels around the camera lens. 2-layer, 0.8 mm KiCad 10 board, DRC-clean, with gerbers, BOM, CPL, STEP and renders.

    30 partsCERN-OHL-S-2.0
  • 6 layers48 × 52 mmKestrel esc, the printed circuit board in 3D

    Kestrel esc

    HeyPCB/kestrel-esc

    Kestrel 4in1: 6S 4-in-1 ESC running stock AM32 on four STM32G071s, with 24 CSD18540 FETs, LM5109B drivers and battery current sensing. 48 x 52 mm 6-layer KiCad 10 board, DRC clean, with gerbers, BOM, CPL and STEP.

    174 partsCERN-OHL-S-2.0
  • 6 layers40 × 40 mmKestrel fc, the printed circuit board in 3D

    Kestrel fc

    HeyPCB/kestrel-fc

    Kestrel H7: STM32H743 FPV flight controller with ICM-20602 + BMI088, MS5611, 16 MB blackbox, 5 V and switchable 10 V BECs.

    114 partsCERN-OHL-S-2.0
  • 4 layers28 × 28 mmKestrel gps, the printed circuit board in 3D

    Kestrel gps

    HeyPCB/kestrel-gps

    Kestrel GPS: u-blox MAX-M10S under a 25 mm ceramic patch with an LIS3MDL compass, for Betaflight, INAV and ArduPilot. 28 x 28 mm 4-layer KiCad 10 board, DRC clean, with gerbers, BOM, CPL and STEP.

    14 partsCERN-OHL-S-2.0
  • 2 layers80 × 125.3 mmPhone robot, the printed circuit board in 3D

    Phone robot

    HeyPCB/phone-robot

    Bolt, the phone stand robot: A little robot that holds your phone, charges it, and peeks over the top to tell you how it's eating. KiCad 10, heypcb.ai merch.

    35 partsCERN-OHL-S-2.0
  • 2 layers40.3 × 127.9 mmPlant buddy, the printed circuit board in 3D

    Plant buddy

    HeyPCB/plant-buddy

    Sprout, the plant buddy: A circuit-board sprout that cries a little blue tear when your plant is thirsty. KiCad 10, heypcb.ai merch.

    16 partsCERN-OHL-S-2.0