Skip to the content

Open-source KiCad boards

107,410 boards

Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.

  • 2 layers100 × 86 mmGorilaz, the printed circuit board in 3D

    Gorilaz

    nol00p/Gorillaz

    pcb replacement for the kinesis adv2

    51 parts5
  • 2 layers89 × 95 mmWaveGlide3X, the printed circuit board in 3D

    WaveGlide3X

    nortd/WaveGlide

    An open hardware oxygen system for glider pilots.

    32 parts5
  • 2 layers100 × 99 mmScsiemu, the printed circuit board in 3D

    Scsiemu

    novi/scsiemu-pcb

    Level Converters for SCSI-bus Emulators

    64 parts5
  • 2 layers10 × 34 mmEasy optical pcb, the printed circuit board in 3D

    Easy optical pcb

    ntchris/voron_mod_super_diy

    all about my voron and ERCF mod

    11 parts5GPL-3.0
  • 2 layers184 × 80 mmAdcboard, the printed circuit board in 3D

    Adcboard

    nuclearfutureslab/ibxII-hardware

    Hardware for IBX ][ - nuclear warhead verification with an Apple II

    126 parts5GPL-3.0
  • 4 layers78 × 46 mmHydro, the printed circuit board in 3D

    Hydro

    o7-machinehum/Hydroponic

    Please find the electronics files in the ee folder, all pcb design is done with the open source software KiCad. Is uses an STM32 as the main controller, and an ST L6470 moter driver for the stepper motor.

    69 parts5
  • 2 layers19.8 × 100.1 mmPassive expander, the printed circuit board in 3D

    Passive expander

    oamodular/passive-expander

    It’s 4hp and has 7 patch cable sockets and 8 pins on the back. One for each of the 7, plus a pin for connecting a ground that is sent to each of the sockets.

    8 parts5CC-BY-SA-4.0
  • 2 layers235 × 110 mmOblique Palette 0.5 PCB Main, the printed circuit board in 3D

    Oblique Palette 0.5 PCB Main

    Oblique-Industry/Oblique-Easel

    Code, Electronics, and Industrial Design for the Oblique Easel Artmaschine Cyberdeck

    350 parts5
  • 2 layers100 × 165 mmPcb tentacle, the printed circuit board in 3D

    Pcb tentacle

    octoprobe/tentacle

    Open source hardware as part of octoprobe

    979 parts5MIT
  • 2 layers22.9 × 48.3 mmMDBT42Q breakout, the printed circuit board in 3D

    MDBT42Q breakout

    ogatatsu/MDBT42Q-breakout

    MDBT42Q breakout board of nrf52832 module

    102 parts5
  • 2 layers85 × 100 mmPcad ASCII, the printed circuit board in 3D

    Pcad ASCII

    oldgerman/SAU-G0

    迷你低功耗温湿度计,可定时自动唤醒记录数据保存并串口导出文本表格

    275 parts5
  • 2 layers81 × 58.4 mmCAN Logger, the printed circuit board in 3D

    CAN Logger

    olin-electric-motorsports/AdvancedResearch

    2020 Advanced Research

    61 parts5GPL-3.0
  • 2 layers70.5 × 31 mmEInk panel, the printed circuit board in 3D

    EInk panel

    OliverSwift/e-Ink-Display

    eInk Paper Display on ESP32 and HomeAssistant

    31 parts5AGPL-3.0
  • 4 layers25 × 50 mmPrint and Place PCB, the printed circuit board in 3D

    Print and Place PCB

    ollyoid/Printegrated-Circuits

    GCode post-processor for integrating PCBs into 3D prints

    49 parts5
  • 2 layers114.3 × 40.6 mmKSGER Controller REV 2.0, the printed circuit board in 3D

    KSGER Controller REV 2.0

    omega9380/KSGER-Coverplates

    T12 Soldering Iron control board. A design based on schematics created by Mindstorm88 on the EEVBlog forums.

    54 parts5
  • 2 layers130 × 130 mmLine, the printed circuit board in 3D

    Line

    onlydcx/RCJ2023-Japan

    70 parts5
  • 4 layers43 × 95 mmOe commutator controller, the printed circuit board in 3D

    Oe commutator controller

    open-ephys/commutators

    Active coaxial commutator for electrophysiology

    92 parts5
  • 6 layers76.5 × 339.8 mmFmc host, the printed circuit board in 3D

    Fmc host

    open-ephys/onix-fmc-host

    FMC board to acquire from ONIX headstages and breakout boards

    320 parts5
  • 2 layers68.6 × 53.3 mmLf shield, the printed circuit board in 3D

    Lf shield

    Open-Laboratory/lf-shield

    This is a template for new Freeduino, Arduino shields. The template is made in KiCAD EDA.

    8 parts5
  • 2 layers38.1 × 25.4 mmOpenHAK beta, the printed circuit board in 3D

    OpenHAK beta

    OpenHAK/OpenHAK_beta_hardware

    place for all the OHAK hardware

    41 parts5
  • 2 layers39 × 39 mmUP1-GW UART, the printed circuit board in 3D

    UP1-GW UART

    OpenKNX/OpenKNX-UP1

    OpenKNX system UP1

    67 parts5
  • 2 layers71.8 × 40.8 mmESP32.27, the printed circuit board in 3D

    ESP32.27

    OpenMYR/ESP32-Stepper

    OpenMYR ESP32 controller board, stepper driver with A5984

    71 parts5
  • 2 layers65 × 56.5 mmRRAT, the printed circuit board in 3D

    RRAT

    opentrv/OpenTRV-Arduino-V0p2

    Arduino code for V0p2

    42 parts5Apache-2.0