

Pcb tentacle
Open source hardware as part of octoprobe
- Size
- 100 × 165 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 979
- Nets
- 232
- Pads
- 1,608
- Tracks, vias
- 1,474, 492
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 17 Aug 2024
- Updated
- 29 Oct 2026
Overview
Pcb tentacle is an open-source printed circuit board by octoprobe, from the octoprobe/tentacle repository on GitHub, published under the MIT licence. It is a 2-layer board of 100 × 165 mm with 979 parts on 232 nets, routed with 1,474 tracks and 492 vias.
It is built around the RP2040, W25Q32JVSSIQ and GAQY221S, with the AMS1117-3.3, MT9700 and TXB0108PW among its other parts. Its parts include 57 resistors, 47 capacitors, 21 ICs, 19 diodes and 8 connectors. It belongs with the RP2040 boards of this library.
Main components
7RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q32JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 133MHz 1uA 2.7V~3.6V 20 Years 32Mbit 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHGAQY221S
SOP-4-40℃~+85℃ 1.2V 10000MΩ 150us 2.5kV 200mA 2Ω 500mW 50us 60V 7mA AC,DC One set normally open: 2A (SPST - normally open) SOP-4 Solid State Relays (MOS Output) ROHSSUPSiCSolid State Relays (MOS Output)AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMT9700
SOT-23-5-40℃~+85℃ 1 2.4V~5.5V 2A 80mΩ Active High High Side Switch Short-Circuit Protection(SCP)、Overcurrent Protection(OCP)、Over Temperature Protection SOT-23-5 Power Distribution Switches ROHS西安航天民芯Power Distribution SwitchesTXB0108PW
TSSOP-20-40℃~+85℃ 1 1.2V~3.6V 1.65V~5.5V 100Mbps 8 Automatic direction detection、Power-off protection、Output enable high-impedance Bidirectional Level translator Tri-State TSSOP-20 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level ShiftersPRTR5V0U2X
SOT-143-55℃~+125℃ 0.3pF、0.8pF 100W 10V、15V 5V 6.5V 6A 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
README
kicad/tentacle_v0.8/README.mdOctoprobe Tentacle v0.5

History v0.4 -> v0.5
- Remove silkscreen: R301, U302, R1401, R1505
- Breadbord pads: Only one ground line to leave more space for DUT-boards
- Breadbord: Enlarged for big boards
- buffering capacitor on HUB+5V
- GPIO Pads equal to Tentacle v3
- LEDS less bright (Green LEDs 2k2 -> 4k7)
- Power DUT via PICO-Infra?
-
- DUT is not powerered when Tentacle is plugged in.
-
- Power PICO-Probe via PICO-Infra?
-
- PICO-Probe is by default off.
-
- PICO-Probe Boot pin would be controlled by PICO-Infra.
-
- DUT may be powerered via a jumper
- RP2_INFRA_BOOT via USB Port 2
- RP2_PROBE_BOOT via GPIO
- RP2_PROBE_RUN via GPIO
History v0.5 -> v0.6
- New: Pad for scope ground
- Labels level shifter are currently below the pins and covered by the soldered cables: They should be on top of the pins!
- 2 level shifters
- LED for proberun and probeboot
- DUT was powerered 3V3, now 5V
History v0.6 -> v0.7
-
Rename all project files 'pcb_octoprobe' -> 'pcb_tentacle'
-
Remove D1501
-
R1503 0R -> 1K
-
LED_BLUE D201 is an extended part (C189307) - replace by basic part (C2293)
-
LED_BLUE
LED_0603_1608Metric->LED_SMD:LED_0805_2012Metric -
LED_GREEN
LED_0603_1608Metric->LED_SMD:LED_0805_2012Metric -
LED_RED
LED_0603_1608Metric->LED_SMD:LED_0805_2012Metric -
LED_RED C2286 -> C2295
-
LED_WHITE
LED_0603_1608Metric->LED_SMD:LED_0805_2012Metric -
LED_WHITE C2290 -> C34499
-
HUB U302: CFG_SEL[1]
- Before GND: Self-powered operation enabled
- Now +3V3: Bus-powered operation
-
Allows to replace PICO_PROBE with a mcu connected via soldered USB. USB pads have been added.
History v0.7 -> v0.7 2026-01-04
-
PCB -> File -> Board Setup -> Design Rules -> Pre-defined Sizes -> Vias
Label Before New Diameter 0.4mm 0.45mm Hole 0.2mm 0.3mm -
PCB -> File -> Board Setup -> Design Rules -> Constraints -> Minimum through hole
- 0.2mm Before
- 0.3mm New
-
PCB -> File -> Board Setup -> Design Rules -> Constraints -> Minimum annular width
- 0.1mm Before
- 0.075mm New
History v0.7 -> v0.7.1 2026-02-18
Bug: README_insufficient_bus_power.md
-
U302 (hub) CFG_SEL
- Before: connected to +3V3
- After: connected to GND
-
J201 Conn_02x05
- Silkscreen with wrong GPIO numbers
History v0.7.1 -> v0.8.0 2026-07-12
- Solder bridge, 100nF parallel to C217
- Silkscreen: 5V/150ms (5V/15ms without bridge)
Parts
979| Qty | Value | Footprint | References |
|---|---|---|---|
| 772 | prototype_NC | 00_project_library:octoprobe_breakout_PB_NC | , , , , , , , , , , , , , , , +756 |
| 30 | 100n | Capacitor_SMD:C_0402_1005Metric | C203, C204, C207, C208, C1501, C1502, C1505, C1506, C1507, C1508, C1509, C1510, C1511, C1512, C1513, C1514 +14 |
| 20 | prototype_GND | 00_project_library:octoprobe_breakout_PB | , , , , , , , , , , , , , , , +4 |
| 10 | 10u | Capacitor_SMD:C_0603_1608Metric | C201, C202, C215, C220, C221, C224, C225, C226, C227, C401 |
| 10 | white | LED_SMD:LED_0805_2012Metric | D101, D601, D701, D801, D901, D1001, D1101, D1201, D1502, D1503 |
| 8 | 2k2 | Resistor_SMD:R_0805_2012Metric | R101, R601, R701, R801, R901, R1001, R1101, R1201 |
| 8 | octoprobe_NetTie_USB_Differential | 00_project_library:octoprobe_NetTie_USB_Differential | NT101, NT102, NT103, NT104, NT105, NT106, NT301, NT302 |
| 7 | 100k | Resistor_SMD:R_0402_1005Metric | R304, R305, R306, R307, R308, R310, R311 |
| 7 | 10k | Resistor_SMD:R_0402_1005Metric | R214, R216, R217, R312, R313, R314, R315 |
| 7 | 390 | Resistor_SMD:R_0805_2012Metric | R602, R702, R802, R902, R1002, R1102, R1202 |
| 7 | GAQY221S | 00_project_library:SOP-4_4.4x4.3mm_P2.54mm | U601, U701, U801, U901, U1001, U1101, U1201 |
| 5 | USB_PROBE_5V | 00_project_library:octoprobe_breakout_PB | BP223, BP225, BP226, BP227, BP228 |
| 4 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R215, R218, R219, R222 |
| 4 | 10K | Resistor_SMD:R_0402_1005Metric | R207, R210, R213, R1504 |
| 4 | 1u | Capacitor_SMD:C_0402_1005Metric | C205, C206, C1503, C1504 |
| 4 | 33R | Resistor_SMD:R_0402_1005Metric | R202, R203, R1501, R1502 |
| 4 | octoprobe_MountingHole | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad | H1305, H1306, H1307, H1308 |
| 3 | 4K7 | Resistor_SMD:R_0805_2012Metric | R105, R106, R301 |
| 3 | AMS1117-3.3 | 00_project_library:SOT-223-3_TabPin2 | U202, U211, U212 |
| 3 | MT9700 | Package_TO_SOT_SMD:SOT-23-5 | U208, U210, U213 |
| 3 | green | LED_SMD:LED_0805_2012Metric | D105, D106, D301 |
| 2 | 0R | Resistor_SMD:R_0603_1608Metric | R220, R221 |
| 2 | 18p | Capacitor_SMD:C_0805_2012Metric | C307, C308 |
| 2 | 1K | Resistor_SMD:R_0805_2012Metric | R201, R204 |
| 2 | 2k2 | Resistor_SMD:R_0402_1005Metric | R1506, R1507 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R302, R303 |
| 2 | Conn_02x20 | 00_project_library:PinSocket_2x20_P2.54mm_Vertical-stackable_squarepad | J1302, J1303 |
| 2 | D_Schottky | Diode_SMD:D_SOD-323_HandSoldering | D204, D205 |
| 2 | JLCPCB Tooling Hole | 00_project_library:JLCPCB_ToolingHole | TH1301, TH1302 |
| 2 | Oscillator-12MHz_2026 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | X201, X202 |
| 2 | RP2040 | 00_project_library:RP2040-QFN-56 | U201, U1501 |
| 2 | TXB0108PW | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U1503, U1504 |
| 2 | W25Q32JVS | 00_project_library:SOIC-8_5.23x5.23mm_P1.27mm | U203, U1502 |
| 1 | 0R | Resistor_SMD:R_0805_2012Metric | R205 |
| 1 | 1 | 00_project_library:octoprobe_relay | UR601 |
| 1 | 1000u | Capacitor_THT:CP_Radial_D8.0mm_P2.50mm | C216 |
| 1 | 100K | Resistor_SMD:R_0402_1005Metric | R1505 |
| 1 | 12k | Resistor_SMD:R_0402_1005Metric | R309 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R1503 |
| 1 | 2 | 00_project_library:octoprobe_relay | UR701 |
| 1 | 24MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y301 |
| 1 | 2K7 | Resistor_SMD:R_0603_1608Metric | R208 |
| 1 | 3 | 00_project_library:octoprobe_relay | UR801 |
| 1 | 4 | 00_project_library:octoprobe_relay | UR901 |
| 1 | 5 | 00_project_library:octoprobe_relay | UR1001 |
| 1 | 6 | 00_project_library:octoprobe_relay | UR1101 |
| 1 | 7 | 00_project_library:octoprobe_relay | UR1201 |
| 1 | B5819W SL | Diode_SMD:D_SOD-123 | D202 |
| 1 | Conn_01x12 | 00_project_library:PinSocket_1x12_P2.54mm_Vertical_squarepad | J1502 |
| 1 | Conn_01x5 | 00_project_library:PinSocket_1x5_P2.54mm_Vertical_squarepad_USB | J202 |
| 1 | Conn_02x05 | 00_project_library:PinSocket_2x05_P2.54mm_Vertical_squarepad | J201 |
| 1 | Conn_02x20 | 00_project_library:PinSocket_2x12_P2.54mm_Vertical_squarepad | J1501 |
| 1 | Conn_02x20 | 00_project_library:PinSocket_2x14_P2.54mm_Vertical_squarepad | J501 |
| 1 | Logo_Open_Hardware_Small | Symbol:OSHW-Logo2_9.8x8mm_SilkScreen | Logo_open_hardware101 |
| 1 | PRTR5V0U2X | Package_SON:Texas_USON-6_1x1.45mm_P0.5mm_SMD | D302 |
| 1 | Scope GND | 00_project_library:octoprobe_breakout_PB | BP203 |
| 1 | TPS2595xx | Package_SON:WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm | U204 |
| 1 | USB2514B_Bi | 00_project_library:Texas_RHH0036C_VQFN-36-1EP_6x6mm_P0.5mm_EP4.4x4.4mm_ThermalVias | U302 |
| 1 | USB_C_Receptacle_USB2.0 | 00_project_library:USB_C_Receptacle_Palconn_UTC16-G | J301 |
| 1 | USB_PROBE_3V3 | 00_project_library:octoprobe_breakout_PB | BP222 |
| 1 | USB_PROBE_D+ | 00_project_library:octoprobe_breakout_PB | BP221 |
| 1 | USB_PROBE_D- | 00_project_library:octoprobe_breakout_PB | BP220 |
| 1 | USB_PROBE_GND | 00_project_library:octoprobe_breakout_PB | BP224 |
| 1 | blue | LED_SMD:LED_0805_2012Metric | D201 |
| 1 | red | LED_SMD:LED_0805_2012Metric | D203 |
More from octoprobe/tentacle
4- 2 layers100 × 165 mm

- 2 layers100 × 165 mm

- 2 layers100 × 165 mm

- 2 layers100 × 160 mm

Similar boards
- 4 layers70 × 45 mm

- 2 layers100 × 90 mm

- 2 layers100 × 100 mm

Hub12-controller hw
radioegor146/hub12-controller
Simple HUB12 LED matrices USB controller using RP2040
88 parts1GPL-3.0 - 2 layers78 × 60 mm

- 4 layers219 × 108.5 mm

Z80DevBoard
gianluca-rainis/Z80DevBoard
An advanced development board for the Z80 microprocessor, powered by an RP2040.
182 parts7CERN-OHL-S-2.0 - 2 layers80 × 50 mm

- 4 layers120 × 80 mm

- 2 layers38 × 66.6 mm

Questions
How big is the Pcb tentacle PCB?
It measures 100 × 165 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Pcb tentacle use?
979 parts, built around the RP2040, W25Q32JVSSIQ, GAQY221S and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pcb tentacle KiCad files?
From the octoprobe/tentacle repository on GitHub, at the commit this page was made from: the board is kicad/tentacle_v0.9/pcb_tentacle.kicad_pcb and its schematic kicad/tentacle_v0.3/pcb_octoprobe.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pcb tentacle design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).