4 layers96 × 55 mm
4 layers120 × 80 mm
Elemrv flask carrierboard
aesc-silicon/kicad-projects1KiCad boards for open-source chips
- Size
- 120 × 80 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 142
- Nets
- 147
- Pads
- 582
- Tracks, vias
- 1,814, 324
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 12 May 2026
- Updated
- 1 Oct 2026
Overview
Elemrv flask carrierboard is an open-source printed circuit board by aesc-silicon, from the aesc-silicon/kicad-projects repository on GitHub. It is a 4-layer board of 120 × 80 mm with 142 parts on 147 nets, routed with 1,814 tracks and 324 vias.
It is built around the RP2040, SN65HVD230DR and TMP1075D, with the W25Q32JVSSIQ, USBLC6-2SC6 and 74LVC1G02Z among its other parts. Its parts include 46 resistors, 38 capacitors, 16 ICs, 8 connectors and 6 diodes. It belongs with the computers and single-board computers boards and the RP2040 boards of this library.
Main components
12
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
SN65HVD230DR
SOP-8CAN TransceiversTokmas
TMP1075D
SOIC-8-55℃~+125℃ 1.7V~5.5V 12bit 3.5uA 7ms Factory temperature calibration、Temperature threshold monitoring I2C、SMBus ±1℃ SOIC-8 Temperature Sensors ROHSTexas InstrumentsTemperature Sensors
W25Q32JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 133MHz 1uA 2.7V~3.6V 20 Years 32Mbit 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
USBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)
74LVC1G02Z
SOT-553-5-40℃~+125℃ 1 1.65V~5.5V 1.7V~2V 1.7ns@5V,50pF 2 200uA 3.4V~3.8V 32mA 32mA 550mV~800mV 700mV~800mV 74LVC Series NOR Gate SOT-553-5 Logic Gates ROHSDiodes IncorporatedLogic Gates
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
ME6211C12M5G-N
SOT-23-5-40℃~+150℃ 1 1.2V 280mV@(100mA)、500mV@(200mA) 300mA 30uA 50uVrms 6V 70dB@(1kHz) Fixed Over Current Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMICRONEVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
OT2EL4C4JI-111OLP-50M
SMD3225-4P-40℃~+85℃ 1.8V~3.3V 50MHz CMOS ±10ppm ±20ppm SMD3225-4P Crystal Oscillators ROHSYXCCrystal Oscillators
TPD6E001RSE
UQFN-10(1.5x2)-40℃~+85℃ 1.5pF 11V 1nA 6 ESD IEC 61000-4-2 Unidirectional UQFN-10(1.5x2) ESD and Surge Protection (TVS/ESD) ROHSTexas InstrumentsESD And Surge Protection (TVS/ESD)
BAT54
SOT-23200mA 2uA@25V 30V 800mV@100mA Independent SOT-23 Schottky Diodes ROHSFOSANSchottky DiodesPESD1CAN
SOT-23-65℃~+150℃ 11pF 1nA 2 200W@8/20us 24V 30.3V 3A@8/20us 70V Bidirectional ESD IEC 61000-4-2、IEC 61000-4-5 SOT-23 ESD and Surge Protection (TVS/ESD) ROHSNexperiaESD And Surge Protection (TVS/ESD)
README
README.rstKiCad Projects
A collection of PCB designs created with KiCad 9 <https://www.kicad.org/>_.
Projects
.. list-table:: :header-rows: 1 :widths: 30 70
-
- Project
- Description
-
i2c-gpio-expander <i2c-gpio-expander/>_- I2C-based GPIO expander board, rev 1.
(
GitHub <https://github.com/aesc-silicon/i2c-gpio-expander>_)
License
All designs in this repository are licensed under the
CERN Open Hardware Licence Version 2 - Strongly Reciprocal (CERN-OHL-S-2.0) <LICENSE>_.
SPDX-License-Identifier: CERN-OHL-S-2.0
Parts
142| Qty | Value | Footprint | References |
|---|---|---|---|
| 21 | 100n | PCM_JLCPCB:C_0402 | C1, C15, C22, C23, C24, C25, C26, C27, C30, C34, C35, C36, C37, C40, C41, C42 +5 |
| 21 | 10k | PCM_JLCPCB:R_0402 | R1, R2, R11, R13, R17, R22, R24, R26, R27, R28, R29, R45, R46, R48, R50, R51 +5 |
| 8 | MountingHole_Pad | MountingHole:MountingHole_2.7mm_M2.5_DIN965_Pad | H1, H2, H3, H4, H5, H6, H7, H8 |
| 7 | 1u | PCM_JLCPCB:C_0402 | C8, C10, C12, C16, C20, C21, C32 |
| 7 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP4, TP7, TP11, TP13, TP14, TP16, TP17 |
| 5 | TestPoint | TestPoint:TestPoint_Pad_1.0x1.0mm | TP1, TP2, TP3, TP9, TP12 |
| 4 | 1k | PCM_JLCPCB:R_0402 | R7, R21, R32, R33 |
| 4 | 5.1k | PCM_JLCPCB:R_0402 | R4, R6, R47, R49 |
| 3 | 100k | PCM_JLCPCB:R_0402 | R10, R36, R37 |
| 3 | 10u | PCM_JLCPCB:C_0402 | C3, C4, C5 |
| 3 | Red | PCM_JLCPCB:D_0603 | D2, D5, D6 |
| 3 | Tactile Button, 160gf | PCM_JLCPCB:SW_TS-1088-AR02016 | S1, S2, S3 |
| 2 | 1M | PCM_JLCPCB:R_0402 | R3, R44 |
| 2 | 2.2k | PCM_JLCPCB:R_0402 | R23, R25 |
| 2 | 2.2n | PCM_JLCPCB:C_0402 | C2, C28 |
| 2 | 27R | PCM_JLCPCB:R_0402 | R19, R20 |
| 2 | 27p | PCM_JLCPCB:C_0402 | C18, C19 |
| 2 | 59R | PCM_JLCPCB:R_0603 | R54, R55 |
| 2 | LM809 | PCM_JLCPCB:SOT-23-3_L2.9-W1.3-P1.90-LS2.4-BR | U11, U12 |
| 2 | USBLC6-2SC6 | PCM_JLCPCB:SOT-23-6_L2.9-W1.6-P0.95-LS2.8-BL | U3, U22 |
| 2 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4085 | J3, J4 |
| 2 | ~ | PCM_JLCPCB:Part_Num_JLCPCB | chip1, company1 |
| 1 | 0R | PCM_JLCPCB:R_0603 | R43 |
| 1 | 10k | Potentiometer_SMD:Potentiometer_Bourns_TC33X_Vertical | RV1 |
| 1 | 10p | PCM_JLCPCB:C_0402 | C17 |
| 1 | 12k | Resistor_SMD:R_0402_1005Metric | R58 |
| 1 | 150R | PCM_JLCPCB:R_0402 | R40 |
| 1 | 1n | PCM_JLCPCB:C_0402 | C14 |
| 1 | 220R | PCM_JLCPCB:R_0402 | R39 |
| 1 | 25LCxxx | PCM_JLCPCB:SOIC-8_3.9x4.9mm_P1.27mm | U21 |
| 1 | 33R | PCM_JLCPCB:R_0402 | R14 |
| 1 | 4.7n | PCM_JLCPCB:C_0402 | C29 |
| 1 | 680R | PCM_JLCPCB:R_0402 | R38 |
| 1 | 74LVC1G02 | PCM_JLCPCB:SOT-23-5_L3.0-W1.7-P0.95-LS2.8-BR | U7 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | BAT54 | PCM_JLCPCB:D_SOT-23 | D4 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J8 |
| 1 | Conn_02x08_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x08_P2.54mm_Vertical | J2 |
| 1 | Conn_02x12_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x12_P2.54mm_Vertical | J7 |
| 1 | Flask_J_CB | Connector_Hirose_aesc-silicon:Hirose_DF40C-100DS-0.4V_2x50_P0.4mm | J6 |
| 1 | Fuse | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | LED_ARGB | LED_SMD_aesc-silicon:FM-B2020RGBA-HG | D7 |
| 1 | M24C02 | PCM_JLCPCB:SOIC-8_L4.9-W3.9-P1.27-LS6.0-BL | U20 |
| 1 | ME6211C12M5 | PCM_JLCPCB:SOT-23-5_L3.0-W1.7-P0.95-LS2.8-BL | U9 |
| 1 | Micro_SD_Card_Det2 | Connector_Card:microSD_HC_Hirose_DM3D-SF | J5 |
| 1 | OT2EL4C4JI-111OLP-50M | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | U15 |
| 1 | PESD1CAN | Package_TO_SOT_SMD:SOT-23 | D8 |
| 1 | RP2040 | PCM_JLCPCB:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm_ThermalVias | U18 |
| 1 | SN65HVD230DR | PCM_JLCPCB:SOIC-8_L4.9-W3.9-P1.27-LS6.0-BL | U24 |
| 1 | TMP1075D | PCM_JLCPCB:SOIC-8_3.9x4.9mm_P1.27mm | U19 |
| 1 | TPD6E001 | Package_DFN_QFN:Texas_UQFN-10_1.5x2mm_P0.5mm | U23 |
| 1 | TPS3702CX12DDCT | PCM_JLCPCB:SOT-23-6_L2.9-W1.6-P0.95-LS2.8-BL | U14 |
| 1 | W25Q32JVSS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U1 |
| 1 | X322512MSB4SI | PCM_JLCPCB:CRYSTAL-SMD_4P-L3.2-W2.5-BL | X1 |
More from aesc-silicon/kicad-projects
4- 4 layers40 × 30 mm
- 2 layers51 × 21 mm
- 2 layers40 × 30 mm
Similar boards
- 6 layers180 × 120 mm
DCJ11CoreBoard v1.3
CYP4502D6/DCJ11CoreBoard
PDP-11 replica project based on the DEC DCJ-11 chipset, utilizing FPGA as bus controller and peripheral emulator, using external SRAM to provide system memory
234 parts13GPL-3.0 - 4 layers72.6 × 170 mm
OpenJBOD RP2040
OpenJBOD/rp2040
This repository contains the hardware design files OpenJBOD RP2040 Baseboard.
129 parts87CERN-OHL-P-2.0 - 4 layers60 × 56.1 mm
AvionicsPower
esb8/AvionicsPower
PCB of a Power Management and supply board for an Avionics stack.
82 parts2 - 4 layers140 × 70 mm
- 4 layers98.1 × 94.4 mm
- 8 layers167.2 × 95.4 mm
- 2 layers74 × 37 mm
- 2 layers120 × 60 mm
Overglade Badges
KaiPereira/Overglade-Badges
NFC hackathon badges for the Overglade game jam in Singapore!
69 parts126
Questions
How big is the Elemrv flask carrierboard PCB?
It measures 120 × 80 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Elemrv flask carrierboard use?
142 parts, built around the RP2040, SN65HVD230DR, TMP1075D and W25Q32JVSSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Elemrv flask carrierboard KiCad files?
From the aesc-silicon/kicad-projects repository on GitHub, at the commit this page was made from: the board is elemrv-flask-carrierboard/elemrv-flask-carrierboard.kicad_pcb and its schematic elemrv-flask-carrierboard/clock_reset.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Elemrv flask carrierboard design in my own project?
Its repository states no licence, so its author keeps all rights: ask aesc-silicon before reusing the design.