
8bit quad fc
VasilKalchev/8bit-quad.hw
Flight controller PCB for a custom-built quadcopter based on the ATmega328 microcontroller.
KiCad boards from 598 GitHub repositories tagged “pcb-design”, the most starred first; open any of them in PCBKit.

VasilKalchev/8bit-quad.hw
Flight controller PCB for a custom-built quadcopter based on the ATmega328 microcontroller.

verma-suraj/ESP32_custom
A 3D walkthrough of the board is available in demo/3D view of the Board.mp4.

Vibhors-Tech-Hub/ESP32-S3-Dev-Board
A 4-layer dev board around the ESP32-S3-MINI-1 with dual USB-C ports

vishalbodkhe/5V-Regulated-Power-Supply-PCB
12V DC to 5V regulated power supply PCB designed using KiCad with protection, filtering, DRC verification and Gerber files.

vishalbodkhe/555-Timer-LED-Blinker-PCB
555 Timer LED Blinker PCB designed using KiCad

vishalbodkhe/ESP32-Environmental-Monitoring-PCB
ESP32-based environmental monitoring PCB designed in KiCad with DHT11, LDR, OLED, custom routing, GND zone and manufacturing-ready Gerber files.

vishalbodkhe/ESP32-Smart-Temperature-Fan-Controller
KiCad PCB design of an ESP32 based smart temperature and fan controller.

vishalbodkhe/LDR-Automatic-Light-Control-PCB
LDR-based automatic light control system with custom KiCad PCB design, DRC verification, Gerber files and 3D visualization.

vishnukashikar/STM32-Sensor-Board
KiCad design for a custom STM32C031 board with an MPU-6050 accelerometer/gyroscope, USB-C power, SWD header and GPIO breakout.

VolcanoKing370/xor-gate-toy
This is a simple quad XOR gate (74HC86) that is controlled by 8 key switches and outputs to 4 LEDS, all powered by a coin cell battery. This is implemented in KiCAD.

wasylews/soilsense
A low-power soil moisture and climate sensor on an ESP-01, powered by a single 18650 cell for an estimated six months. Custom PCB and a 3D-printed enclosure.

wemsh05/65_percent_keyboard
This would be my first attempt to make a 65% keyboard pcb and hopefully the shell

Will946/GNSS
u-blox ZED-F9P RTK GNSS breakout board with dual-band L1/L2 reception and centimeter-level positioning accuracy.

wirenux/USBC-UART
A simple project to convert a traditional USB-B UART bridge schematic to a modern USB-C interface.

xmyoot/esp32c6-epaper-calendar
USB-powered XIAO ESP32C6 carrier for a bare 7.5-inch e-paper panel: KiCad hardware, firmware, fabrication files, and review evidence. Prototype testing pending.

xmyoot/rpi-cm5-edge-carrier
Raspberry Pi CM5 edge-AI audio carrier: KiCad 10, 4-layer impedance-controlled, USB-C PD, NVMe, USB3, GbE, I2S mic link. DRC-clean, JLCPCB-ready, fully scripted.

Yadnik1/Low-Cost-Telematics-Device
Developed a cost-effective telematics device for automobiles, capable of enabling user-based insurance models to save up to 30% on premiums.

yymqd/kicad-pcb-agent-skills
AI Agent (Hermes) 驱动的 KiCad PCB 设计自动化技能集:三条管线(kicad-cli / MCP-KiCad / kcaa)阶段切换工作流

zgeez/Pixel-Badge
Wearable 32x32 LED badge with Zephyr firmware, BLE control, passive NFC, and a Flutter Android app, built around a custom nRF52840 PCB.

Ziegen-EE/KiCad-LED-Key
A compact, through-hole PCB designed in KiCad featuring a single momentary switch, one LED, and one current-limiting resistor.

zizofr/voltmeter_PCB
a home made PCB of a digital voltmeter, embedded with a firmware to measure the electric tension

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!