Skip to the content
4 layers118 × 76 mmSmart led badge, the printed circuit board in 3D

Smart led badge

zgeez/Pixel-Badge

Wearable 32x32 LED badge with Zephyr firmware, BLE control, passive NFC, and a Flutter Android app, built around a custom nRF52840 PCB.

Size
118 × 76 mm
Copper layers
4
Thickness
1.6 mm
Parts
1,236
Nets
212
Pads
2,831
Tracks, vias
5,653, 1,619
Pours
9
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
4 Oct 2026
Updated
4 Nov 2026

Overview

Smart led badge is an open-source printed circuit board by zgeez, from the zgeez/Pixel-Badge repository on GitHub, published under the MIT licence. It is a 4-layer board of 118 × 76 mm with 1,236 parts on 212 nets, routed with 5,653 tracks and 1,619 vias.

It is built around the E73-2G4M08S1C, TLC59283RGER and TPS61023DRL, with the TPS63802DLAR, SN74HC595PWRE4 and BQ25620RYKR among its other parts. Its parts include 58 resistors, 43 capacitors, 39 transistors, 17 ICs and 4 inductors. It belongs with the lEDs and displays and radio and wireless boards and the nRF52 and nRF5x boards of this library.

Main components

12

README

hardware/README.md

Hardware

The KiCad 10.0.6 project for the Rev A badge: a 118 × 76 mm, four-layer board with every assembled part on the front. Boards are built and running (bring-up record).

Open smart-led-badge.kicad_pro. Project libraries use ${KIPRJMOD} paths, and you'll also need KiCad's standard libraries.

PathContents
smart-led-badge.kicad_sch, sheets/Schematic
smart-led-badge.kicad_pcbRouted board
smart-led-badge.kicad_druCustom design rules
libraries/Symbols, footprints and where they came from
mechanical/3MF print files, below

Board

  • 1.6 mm, 3 mm corner radius, JLC04161H-7628 stack-up, tented vias.
  • Rows route on F.Cu and columns via to In2.Cu. In1.Cu is ground apart from three short links.
  • 0.127 mm minimum track and space, 0.45/0.2 mm vias. The custom rules allow the matrix LEDs' courtyards to touch.
  • Keep-outs for the NFC coil, the antenna and the battery. Nothing is assembled or exposed under the pack.
  • Test points, battery polarity and controls are labelled on silkscreen. Reference designators aren't printed.

Print files

FilePart
rear-carrier.3mf, front-face.3mfThe two halves of the carrier
matrix-pixel-grid.3mf, matrix-diffuser.3mfBlack 2 mm grid and white diffuser over the matrix
mode-button-cap.3mf, action-button-cap.3mf, button-plunger.3mfButton parts
magnetic-backing.3mf, magnet-retaining-cap.3mfMagnetic mount
m2-thread-coupon.3mfTest print for the M2 threads
pcb-no-rear-jst.3mfBoard dummy for fit checks (without the rear connector)

The diffuser is what makes the QR code readable for phones. Fit, latch retention and wear still need checking on prints.

Checks

powershell
.\scripts\dev.ps1 hardware

On Linux, make hardware. It runs ERC, checks that symbol pin numbers match footprint pads, and exports PDF and BOM files to build/hardware/. It doesn't check footprint geometry or pin functions, and DRC is separate. Gerbers, drill, placement and STEP files are generated and kept out of the repository.

Hardware overview, bring-up checklist.

Parts

1,236
QtyValueFootprintReferences
1024KT-0603Wsmart-led-badge:LED_0603_KENTO_KT-0603LD1000, LD1001, LD1002, LD1003, LD1004, LD1005, LD1006, LD1007, LD1008, LD1009, LD1010, LD1011, LD1012, LD1013, LD1014, LD1015 +1008
34AO3401APackage_TO_SOT_SMD:SOT-23Q201, Q203, Q701, Q702, Q703, Q704, Q705, Q706, Q707, Q708, Q709, Q710, Q711, Q712, Q713, Q714 +18
18100nFCapacitor_SMD:C_0402_1005MetricC207, C208, C301, C302, C601, C603, C701, C702, C703, C704, C705, C706, C709, C710, C711, C1101 +2
13100kResistor_SMD:R_0402_1005MetricR203, R208, R214, R219, R222, R223, R303, R306, R313, R316, R703, R704, R705
110Resistor_SMD:R_0402_1005MetricR206, R207, R402, R403, R602, R604, R701, R1001, R1002, R1003, R1004
1010kResistor_SMD:R_0402_1005MetricR201, R309, R311, R312, R702, R901, R902, R1103, R1201, R1202
84x10kResistor_SMD:R_Array_Convex_4x0603RN701, RN702, RN703, RN704, RN705, RN706, RN707, RN708
610uF 25VCapacitor_SMD:C_0805_2012MetricC201, C203, C304, C309, C707, C708
64.7kResistor_SMD:R_0402_1005MetricR211, R217, R314, R315, R1101, R1102
522uF 25VCapacitor_SMD:C_0805_2012MetricC202, C204, C205, C307, C308
5AO3400APackage_TO_SOT_SMD:SOT-23Q202, Q204, Q301, Q302, Q303
4SN74HC595Package_SO:TSSOP-16_4.4x5mm_P0.65mmU702, U703, U704, U705
312kResistor_SMD:R_0402_1005MetricR204, R304, R307
34.7uF 16VCapacitor_SMD:C_0603_1608MetricC306, C401, C402
347kResistor_SMD:R_0402_1005MetricR218, R220, R221
3M2MountingHole:MountingHole_2.2mm_M2H1301, H1302, H1303
20Resistor_SMD:R_0805_2012MetricR209, R215
212pFCapacitor_SMD:C_0402_1005MetricC405, C406
21uFCapacitor_SMD:C_0402_1005MetricC602, C604
21uHsmart-led-badge:L_Coilcraft_XGL4020L202, L301
22.94kResistor_SMD:R_0402_1005MetricR601, R603
220kResistor_SMD:R_0402_1005MetricR202, R205
25.1kResistor_SMD:R_0402_1005MetricR301, R302
2GNDsmart-led-badge:TestPoint_Pad_D0.8mmTP207, TP311
2TLC59283Package_DFN_QFN:Texas_RGE0024C_VQFN-24-1EP_4x4mm_P0.5mm_EP2.1x2.1mm_ThermalViasU601, U602
1+3V3smart-led-badge:TestPoint_Pad_D0.8mmTP204
10.47uHsmart-led-badge:L_Murata_DFE201612EL201
1100nF C0GCapacitor_SMD:C_1206_3216MetricC1001
110k B3380/3434Resistor_SMD:R_0402_1005MetricTH301
110nFCapacitor_SMD:C_0402_1005MetricC903
11kResistor_SMD:R_0402_1005MetricR1203
11uF 50VCapacitor_SMD:C_0603_1608MetricC303
12.2Resistor_SMD:R_0603_1608MetricR401
12.2uF X7RCapacitor_SMD:C_0603_1608MetricC902
1200kResistor_SMD:R_0402_1005MetricR216
132.768kHz 9pFCrystal:Crystal_SMD_3215-2Pin_3.2x1.5mmY401
133kResistor_SMD:R_0402_1005MetricR210
13V3_REGsmart-led-badge:TestPoint_Pad_D0.8mmTP203
14.7nFCapacitor_SMD:C_0402_1005MetricC206
147nF 16VCapacitor_SMD:C_0402_1005MetricC305
1Action/Selectsmart-led-badge:SW_XUNPU_TS-1088SW1202
1BQ25620smart-led-badge:Texas_RYK0018AU302
1Battery JST-PH 2PConnector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalJ302
1CC1TestPoint:TestPoint_Pad_D1.0mmTP309
1CC2TestPoint:TestPoint_Pad_D1.0mmTP310
1CHG_STATTestPoint:TestPoint_Pad_D1.0mmTP308
1COL0TestPoint:TestPoint_Pad_D1.0mmTP601
1DNPCapacitor_SMD:C_0402_1005MetricC1102
1E73-2G4M08S1Csmart-led-badge:Ebyte_E73-2G4M08S1CU401
1EN_3V3TestPoint:TestPoint_Pad_D1.0mmTP209
1ICM-42688-PPackage_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4yU901
1MTX_BLANKTestPoint:TestPoint_Pad_D1.0mmTP701
1MTX_LATTestPoint:TestPoint_Pad_D1.0mmTP607
1MTX_SAFE_SENSETestPoint:TestPoint_Pad_D1.0mmTP703
1MTX_SCKTestPoint:TestPoint_Pad_D1.0mmTP605
1Mode/Nextsmart-led-badge:SW_XUNPU_TS-1088SW1201
1NFC coil 30x25mm 6T (PCB)smart-led-badge:L_NFC_Coil_30x25mm_6TL1101
1NT3H2111W0FHKHsmart-led-badge:NXP_XQFN-8_SOT902-3U1101
1PCM12SMTRButton_Switch_SMD:SW_SPDT_PCM12SW201
1PDM_CLKTestPoint:TestPoint_Pad_D1.0mmTP1001
1PDM_DINTestPoint:TestPoint_Pad_D1.0mmTP1002
1PG_3V3TestPoint:TestPoint_Pad_D1.0mmTP210
1PWR_SW_NTestPoint:TestPoint_Pad_D1.0mmTP216
1QONTestPoint:TestPoint_Pad_D1.0mmTP307
1ROW0TestPoint:TestPoint_Pad_D1.0mmTP708
1ROW16TestPoint:TestPoint_Pad_D1.0mmTP709
1RedLED_SMD:LED_0603_1608MetricD1201
1SCAN_OKTestPoint:TestPoint_Pad_D1.0mmTP704
1SN74LVC1G04Package_TO_SOT_SMD:SOT-23-5U707
1SN74LVC1G123Package_SO:SSOP-8_2.95x2.8mm_P0.65mmU706
1SN74LVC1G32Package_TO_SOT_SMD:SOT-23-5U708
1SN74LVC8T245Package_SO:TSSOP-24_4.4x7.8mm_P0.65mmU701
1SPH0641LM4H-1smart-led-badge:Knowles_LGA-5_3.5x2.65mm_Hole0.6mmMK1001
1SWD 2x5 1.27mmConnector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMDJ501
1SYSsmart-led-badge:TestPoint_Pad_D0.8mmTP201
1TPD4E05U06smart-led-badge:TI_DQA0010A_USON-10_2.5x1.0mm_P0.5mmU301
1TPS61023smart-led-badge:Texas_DRL0006AU202
1TPS63802smart-led-badge:Texas_DLA0010AU201
1TSTestPoint:TestPoint_Pad_D1.0mmTP305
1TYPE-C-31-M-12smart-led-badge:USB_C_Receptacle_HRO_TYPE-C-31-M-12J301

The 1,229 most common of 1,236 parts.

Similar boards

  • 4 layers152.3 × 72 mmIr glasses EVT E7, the printed circuit board in 3D

    Ir glasses EVT E7

    noahzhy/cc_glasses

    tools/ 为此次整改的重建和检查脚本;日常直接编辑 KiCad 工程。重建脚本会覆盖设计,不能在人工修改后直接重跑。Python 工具不引入继承类;需要 KiCad 10 的 pcbnew Python,以及 Python 3 的 sexpdata、numpy、scipy、shapely、pymupdf。

    171 parts1MIT
  • 2 layers47.7 × 80.7 mmChristmas tree ear ring, the printed circuit board in 3D

    Christmas tree ear ring

    arvindsa/xmas-tree-earring

    A pair of wireless, synchronized LED earrings with nRF52 MCUs running deterministic animation patterns.

    65 parts
  • 6 layers25 × 42.5 mmSerene Mini, the printed circuit board in 3D

    Serene Mini

    cshariq/Serene

    Can't hear your friend talking on the highway? Do you need to blast your music just to hear it well? Well, you're in luck, because Serene is a portable noise-cancelling device that can remove all of that noise!

    81 parts
  • 2 layers100 × 100 mmLorenz, the printed circuit board in 3D

    Lorenz

    gallicchio/ai_unleashes_chaos

    Lorenz Attractor Circuit by Paul Horowitz in KiCAD

    90 parts1MIT
  • 2 layers53.4 × 84.4 mmPOV card v1, the printed circuit board in 3D

    POV card v1

    ExcessiveOverkill/POV-card-v1

    Persistence-of-vision shake light-up badges designed by Excessive Overkill

    64 parts5
  • 2 layers53.4 × 84.4 mmPCB business cards, the printed circuit board in 3D

    PCB business cards

    ExcessiveOverkill/PCB-business-cards

    Everything needed to make your own persistence of vision business cards

    70 parts3
  • 2 layers110 × 82 mm7-seg display-2-digits, the printed circuit board in 3D

    7-seg display-2-digits

    sburgic/poc-and-obsolete

    Proof of concepts and old (obsolete) projects

    47 parts

Questions

How big is the Smart led badge PCB?

It measures 118 × 76 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Smart led badge use?

1,236 parts, built around the E73-2G4M08S1C, TLC59283RGER, TPS61023DRL and TPS63802DLAR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Smart led badge KiCad files?

From the zgeez/Pixel-Badge repository on GitHub, at the commit this page was made from: the board is hardware/smart-led-badge.kicad_pcb and its schematic hardware/sheets/debug.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Smart led badge design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).