Skip to the content

TPS63802DLAR

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 1.3V~5.5V 1.4MHz、1.6MHz、2.1MHz 1.8V~5.2V 11uA 2A Adjustable Buck-Boost Buck-Boost Built-in Yes VSON-10(2x3) DC-DC Converters ROHS

Part id
ti/TPS63802DLAR
Category
DC DC Converters
Package
VSON-10(2x3)
Pins
10
In stock
25,037 at JLCPCB (C2845237)
Used on
73 open-source boards

Overview

The TPS63802DLAR is a DC DC Converter made by Texas Instruments in a VSON-10(2x3) package with 10 pins. -40℃~+125℃@(TJ) 1 1.3V~5.5V 1.4MHz、1.6MHz、2.1MHz 1.8V~5.2V 11uA 2A Adjustable Buck-Boost Buck-Boost Built-in Yes VSON-10(2x3) DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Celestial_Power_Switchmode:TI TPS63802DLA, from Altium's library) and its footprint (EasyEDA_Cloud:VSON-10_L3.0-W2.0-P0.50-TL, from EasyEDA), ready for a KiCad board. 25,037 are in stock at JLCPCB (part C2845237). 73 open-source boards in 59 repositories on GitHub use it.

Symbol

10VIN1EN9L17L22MODE8GND3AGND6VOUT4FB5PG
Celestial_Power_Switchmode:TI TPS63802DLAFrom Altium's library

Footprint

EasyEDA_Cloud:VSON-10_L3.0-W2.0-P0.50-TLFrom EasyEDA

From the datasheet

16
Supply, least
1.3 V · VIN, recommended operating min; startup requires >1.8 V until power good · p. 5
Supply, most
5.5 V · VIN, recommended operating max · p. 5
Supply, absolute maximum
6 V · VIN, absolute maximum · p. 5
Junction, hottest
150 °C · junction temperature absolute maximum · p. 5
Takes working
11 µA · VIN quiescent current typical; enabled, 3.6 V input, 3.3 V output, not switching · p. 6
Takes asleep
45 nA · VIN shutdown current typical; EN low, VIN = 3.6 V, VOUT = 0 V · p. 6
Gives
2 A · rated output current; VI ≥ 2.3 V, VO = 3.3 V · p. 1
Current limit
5 A · peak inductor current limit typical, boost mode · p. 6
Current limit
3.8 A · peak inductor current limit typical, buck mode · p. 6
Feedback reference
500 mV · FB regulation voltage typical · p. 6
Switches at
2.1 MHz · typical boost mode; VIN = 2.3 V, VOUT = 3.3 V, no load, MODE high · p. 7
Switches at
1.4 MHz · typical buck-boost mode; VIN = VOUT = 3.3 V, no load, MODE high · p. 7
Switches at
1.6 MHz · typical buck mode; VIN = 4.3 V, VOUT = 3.3 V, no load, MODE high · p. 7
Junction to air (VSON)
81 K/W · junction-to-ambient thermal resistance · p. 5
Junction to case (VSON)
36.4 K/W · junction-to-case top thermal resistance · p. 5
Junction to board (VSON)
23.4 K/W · junction-to-board thermal resistance · p. 5

What it is and has

11
Converter
2-A, high-efficient, low IQ buck-boost converter · p. 1
Output voltage
1.8 V to 5.2 V, adjustable · p. 1
Control architecture
Peak current buck-boost · p. 1
Current operation
Forward and reverse · p. 1
Startup
Supports pre-biased outputs · p. 1
Soft start
Integrated · p. 1
Protection
Overtemperature and overvoltage · p. 1
Shutdown
True shutdown with load disconnect · p. 1
Current limit
Forward and backward · p. 1
Mode selection
Automatic PWM/PFM at LOW; forced PWM at HIGH; MODE must not float · p. 11
Package
10-Pin DLA · p. 4

Around it

6
ind 0.47 µH
between L1 and L2; Typical application inductor; effective inductance range 0.37 to 0.57 uH. · p. 5
cap 22 µF
between VOUT and GND; Single ceramic output capacitor for output voltages ≤ 3.6 V; place close to VOUT and power ground. · p. 19
cap 2x 22 µF
between VOUT and GND; Ceramic output capacitors for output voltages above 3.6 V; place close to VOUT and power ground. · p. 19
cap 10 µF
between VIN and GND; X5R or X7R ceramic; place close to VIN and power ground. · p. 19
cap 47 µF
between VIN and GND; Additional electrolytic or tantalum bulk capacitance may be required when the input supply is more than a few inches away. · p. 19
res ≤ 100 kΩ
between FB and GND; Low-side feedback resistor R2; page 12 more strictly requires less than 100 kΩ. · p. 19

Specifications

56
ParameterConditionsAs printedPage
Voltage(2)VIN, L1, L2, EN, MODE, VOUT, FB, PG; over junction temperature range; relative to groundmin -0.3 · max 6 V5
Voltage(2)L1, L2 (AC, less than 10 ns); relative to groundmin -3 · max 9 V5
Operating junction temperature, TJ TJmin -40 · max 150 °C5
Storage temperature, Tstg Tstgmin -65 · max 150 °C5
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ± ratingmax 2000 V5
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ± ratingmax 500 V5
Input voltage VIMinimum startup voltage of VI > 1.8 V until power goodmin 1.3 · max 5.5 V5
Output voltage VOmin 1.8 · max 5.2 V5
Effective capacitance connected to VIN CINOM column recorded as typmin 4 · typ 5 uF5
Effective inductance LNOM column recorded as typmin 0.37 · typ 0.47 · max 0.57 uH5
TPS63802 Effective capacitance connected to VOUT CO1.8 V ≤ VO ≤ 2.3 Vmin 10 uF5
TPS63802 Effective capacitance connected to VOUT COVO > 2.3 V; NOM column recorded as typmin 7 · typ 8.2 uF5
Operating junction temperature TJmin -40 · max 125 °C5
Junction-to-ambient thermal resistance RΘJATPS63802, VSON, 10 PINStyp 81 °C/W5
Junction-to-case (top) thermal resistance RΘJC(top)TPS63802, VSON, 10 PINStyp 36.4 °C/W5
Junction-to-board thermal resistance RΘJBTPS63802, VSON, 10 PINStyp 23.4 °C/W5
Junction-to-top characterization parameter ΨJTTPS63802, VSON, 10 PINStyp 0.9 °C/W5
Junction-to-board characterization parameter ΨJBTPS63802, VSON, 10 PINStyp 23.5 °C/W5
Minimum input voltage for full load, once started VIN;LOADIOUT = 2 A, VOUT = 3.3 V, TJ = 25°Ctyp 2.3 V6
Quiescent current into VIN IQ;VINTPS63802; TJ = 25°C, EN = VIN = 3.6 V, VOUT = 3.3 V, not switchingtyp 11 uA6
Shutdown current into VIN ISDEN = low, -40°C ≤ TJ ≤ 85°C, VIN = 3.6 V, VOUT = 0 Vtyp 45 · max 600 nA6
Undervoltage lockout threshold UVLOVIN falling, VOUT ≥ 1.8 V, once startedmin 1.2 · typ 1.25 · max 1.29 V6
Undervoltage lockout threshold UVLOVIN risingmin 1.6 · typ 1.7 · max 1.79 V6
Thermal shutdown TSDTemperature risingtyp 150 °C6
Thermal shutdown hysteresis TSD;HYSTtyp 20 °C6
Soft-start, Current limit ramp time TrampTJ = 25°C, VIN = 3.6 V, VOUT = 3.3 V, IO = 3.5 A, time from first switching to power goodtyp 224 us6
Delay from EN-edge until rising VOUT TdelayTJ = 25°C, VIN = 3.6 V, VOUT = 3.3 V; delay from EN-edge until first switchingtyp 321 us6
Threshold Voltage rising for EN-Pin VTHR;ENmin 1.07 · typ 1.1 · max 1.13 V6
Threshold Voltage falling for EN-Pin VTHF;ENmin 0.97 · typ 1 · max 1.03 V6
High-level input voltage VIHLogic signals EN, MODEmin 1.2 V6
Low-level input voltage VILLogic signals EN, MODEmax 0.4 V6
Power Good threshold voltage VPG;risingVOUT rising, referenced to VOUT nominaltyp 95 %6
Power Good threshold voltage VPG;fallingVOUT falling, referenced to VOUT nominaltyp 90 %6
Power Good low-level output voltage VPG;LowISINK = 1 mAmax 0.4 V6
Power Good delay time tPG;delayVFB fallingtyp 14 us6
Input leakage current Ilkgtyp 0.01 · max 0.2 uA6
Shutdown current into VOUT ISDEN = low, -40°C ≤ TJ ≤ 85°C, VIN = 3.6 V, VOUT = 3.3 V; typ and max are ± magnitudestyp 0.5 · max 600 nA6
Feedback Regulation Voltage VFBtyp 500 mV6
Feedback Voltage accuracy VFBPWM modemin -1 · max 1 %6
Overvoltage Protection ThresholdVOUT risingmin 5.5 · typ 5.7 · max 5.9 V6
Overvoltage Protection ThresholdVIN risingmin 5.5 · typ 5.7 · max 5.9 V6
Peak Inductor Current to enter PFM-Mode IPWM/PFMVIN = 3.6 V; VOUT = 3.3 Vtyp 1.06 A6
Feedback Input Bias Current IFBVFB = 500 mVtyp 5 · max 100 nA6
Peak Current Limit, Boost Mode IPKTPS63802; VIN ≥ 2.5 Vmin 4 · typ 5 · max 5.75 A6
Peak Current Limit, Buck-Boost Mode IPKTPS63802; VIN ≥ 2.5 Vtyp 5 A6
Peak Current Limit, Buck Mode IPKTPS63802; VIN ≥ 2.5 Vtyp 3.8 A6
Peak Current Limit for Reverse Operation IPK;ReverseVI = 5 V, VO = 3.3 Vtyp -0.9 A6
High-side FET on-resistance Buck RDS;ONVIN = 3 V, VOUT = 3.3 V; I(L2) = 0.19 A; IO = 0.5 Atyp 47 mΩ6
Low-side FET on-resistance Buck RDS;ONVIN = 3 V, VOUT = 3.3 V; I(L2) = 0.19 A; IO = 0.5 Atyp 30 mΩ6
High-side FET on-resistance Boost RDS;ONVIN = 3 V, VOUT = 3.3 V; I(L1) = 0.19 A; IO = 0.5 Atyp 43 mΩ6
Low-side FET on-resistance Boost RDS;ONVIN = 3 V, VOUT = 3.3 V; I(L1) = 0.19 A; IO = 0.5 Atyp 18 mΩ6
Inductor Switching Frequency, Boost Mode fSWVIN = 2.3V, VOUT = 3.3V, no Load, MODE = HIGH, TJ = 25°Ctyp 2.1 MHz7
Inductor Switching Frequency, Buck-Boost Mode fSWVIN = 3.3V, VOUT = 3.3V, no Load, MODE = HIGH, TJ = 25°Ctyp 1.4 MHz7
Inductor Switching Frequency, Buck Mode fSWVIN = 4.3, VOUT = 3.3V, no Load, MODE = HIGH, TJ = 25°Ctyp 1.6 MHz7
Line regulationVIN = 2.4 V to 5.5 V, VOUT = 3.3V, IOUT = 2 Atyp 0.3 %7
Load regulationVIN= 3.6 V, VOUT = 3.3V, IOUT = 0 A to 2 A, forced-PWM modetyp 0.1 %7

Pins, by the datasheet

10
1 EN
Device enable: HIGH enables, LOW disables; must not float. · p. 4
2 MODE
LOW selects power save mode, HIGH selects forced PWM mode; must not float. · p. 4
3 AGND
Analog ground. · p. 4
4 FB
Voltage feedback sensing pin. · p. 4
5 PG
Power good indicator, open-drain output. · p. 4
6 VOUT
Power stage output. · p. 4
7 L2
Connection for inductor. · p. 4
8 GND
Power ground. · p. 4
9 L1
Connection for inductor. · p. 4
10 VIN
Supply voltage input. · p. 4

Open-source boards using it

73See all 73
  • 6 layers68.8 × 74.6 mmFurbyBoard, the printed circuit board in 3D

    FurbyBoard

    Guilleloma/Furby-GPT

    This project transforms a 1998 Furby into an interactive and advanced desktop assistant using a Raspberry Pi W. It incorporates OpenAI and Whisper for natural language processing, primarily relying on Google Cloud Text…

    158 parts26
  • 2 layers176 × 161 mmPanel, the printed circuit board in 3D

    Panel

    afonsus1997/Bongo-Cat-Fidget-Toy

    A simple and satisfying electronic fidget toy featuring Bongo Cat. Track your taps, measure your speed, and toggle display options with intuitive controls.

    405 parts14
  • 4 layers46.3 × 38.6 mmRrr, the printed circuit board in 3D

    Rrr

    PositiveAltitude/rrr-hardware

    77 parts10
  • 4 layers40 × 20 mmDictofun, the printed circuit board in 3D

    Dictofun

    rundb/dictofun

    Very portable voice recorder with speech recognition.

    122 parts6Apache-2.0
  • 2 layersOpensync, the printed circuit board in 3D

    Opensync

    ErichZimmer/OpenSync

    An open source synchronizer for velocimetry of fluids.

    230 parts4CERN-OHL-S-2.0
  • 2 layers50.2 × 95.2 mmCheetoPet, the printed circuit board in 3D

    CheetoPet

    Cheet0sDelet0s/cheetoPet

    an esp32 s3 based tamagotchi

    104 parts3GPL-2.0
  • 4 layers59 × 101 mmEnku mainboard r0.1, the printed circuit board in 3D

    Enku mainboard r0.1

    aliaksei-lameyka/ENKU-Base-reader

    Open enku-mainboard-r0.1.kicadpro with KiCad10.0.7. Matching PCB/root schematic and power.kicadsch, mcuio.kicadsch, epdhv.kicadsch, connectors.kicadsch are canonical.

    127 parts1CERN-OHL-W-2.0

Questions

Is there a KiCad symbol and footprint for the TPS63802DLAR?

Yes. The symbol is Celestial_Power_Switchmode:TI TPS63802DLA and the footprint EasyEDA_Cloud:VSON-10_L3.0-W2.0-P0.50-TL, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS63802DLAR?

VSON-10(2x3), with 10 pins. Its footprint is drawn on this page.

Where is the TPS63802DLAR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS63802DLAR?

JLCPCB lists it as part C2845237, with 25,037 in stock; the sellers' links on this page open their listings.

Which open-source boards use the TPS63802DLAR?

73 boards in 59 repositories on GitHub; the most starred are listed on this page, with their KiCad files.