Skip to the content

Interfaces and adapters

7,328 boards
  • 2 layers33.3 × 51.5 mmGR NPN Breakout, the printed circuit board in 3D

    GR NPN Breakout

    GadgetReboot/NPN_Breakout

    NPN Transistor Breakout Board

    25 parts
  • 2 layers86.8 × 65 mmPower Breakout, the printed circuit board in 3D

    Power Breakout

    GadgetReboot/Power_Breakout

    Power jack/screw terminal distribution PCB with PTC resettable fuses

    34 parts
  • 2 layers115 × 67.5 mmAudio Interface rewire, the printed circuit board in 3D

    Audio Interface rewire

    Gadu1in/audio-interface-pcm2906

    An audio interface designed for low impedance earbuds and an external 3.5mm microphone input

    62 parts
  • 2 layers66 × 40.6 mmEspboard panelize, the printed circuit board in 3D

    Espboard panelize

    gagath/espboard

    ESP8266 ESP-1 firmware flashing PCB adapter.

    17 parts
  • 2 layers37.9 × 20.5 mmNrf24l01 adapter, the printed circuit board in 3D

    Nrf24l01 adapter

    Gallardo7761/nrf24l01_rpi_adapter

    Adapter board to connect an NRF24L01 module to a Raspberry Pi (tested on 4B), meant for a MySensors gateway.

    2 partsGPL-3.0
  • 2 layers33.5 × 26.8 mmRfm95w breakout, the printed circuit board in 3D

    Rfm95w breakout

    Gallardo7761/rfm95w-breakout

    Placa breakout para el módulo LoRa RFM95W.

    6 parts
  • 2 layers40.6 × 49.5 mmKeyboardController, the printed circuit board in 3D

    KeyboardController

    gcoonrod/ps2-parallel

    PS/2 to Parallel Breakout Board

    12 parts
  • 2 layers62.7 × 64.5 mmCn910-breakout, the printed circuit board in 3D

    Cn910-breakout

    GDH-Technologies/sony-cn910-breakout

    Repository for schematics and PCBs for using Sony Camcorders with the VC-195 board and CN910 FPC service port.

    51 parts
  • 2 layers57.4 × 33.8 mmUart isolator, the printed circuit board in 3D

    Uart isolator

    gemarcano/uart_isolator

    41 parts
  • 2 layers165 × 42 mmCAN bus distribution board, the printed circuit board in 3D

    CAN bus distribution board

    geneb/CAN_bus_distribution_board

    This CAN bus distribution board is designed to connect up to 8 devices to a CAN-equipped controller.

    14 parts
  • 2 layers44 × 43 mmRJ45 Interface Board, the printed circuit board in 3D

    RJ45 Interface Board

    geneb/RJ45-Interface-Adapter

    Small board to allow Cat5 cabling to interface to the existing I/O boards in the F-15C project.

    7 partsMIT
  • 4 layers28 × 63.3 mmBreakout board, the printed circuit board in 3D

    Breakout board

    george-vamvakidis/stm32_breakout_board_jtag_ready

    A board with two set of connectors in order to experiment with the STM32F302C8Tx, also jtag rady.

    28 parts
  • 2 layers50 × 50 mmHonda stereo adapter, the printed circuit board in 3D

    Honda stereo adapter

    gh2o/honda-stereo-stuff

    Adapter PCBs for 9th gen Honda Civic steering wheel controls and OEM mic

    10 parts
  • 2 layers60 × 40 mmGas sensor breakout, the printed circuit board in 3D

    Gas sensor breakout

    ginomcfino/gas-sensor-breakout

    PIC16F18344 gas-sensor board with CO2, oxygen, and air-quality sensing, protected power input, programming, and expansion interfaces. Designed in KiCad.

    33 parts
  • 2 layers150 × 100 mmHome automation final, the printed circuit board in 3D

    Home automation final

    ginomcfino/home-automation-controller

    STM32 home automation controller with Ethernet, Zigbee, relay control, and sensor interfaces. Designed in KiCad.

    95 parts
  • 2 layers45 × 25 mmUART RS485 Read only, the printed circuit board in 3D

    UART RS485 Read only

    Git-Narii/UART-RS485_ConversionBoard__ReadOnly

    RS485からUARTに変換するための基板

    22 parts
  • 4 layers31.5 × 76.5 mmPico2w usbc header board, the printed circuit board in 3D

    Pico2w usbc header board

    gjberger/pico2-starter

    Bare-metal C on the Raspberry Pi Pico 2 (RISC-V), no SDK: linker script, minimal lib, UART loader

    44 parts
  • 4 layers90.7 × 78.2 mmSerialHub, the printed circuit board in 3D

    SerialHub

    glingy/uarthub

    A 6-port UART hub

    129 parts
  • 4 layers58.6 × 53.6 mmUsbhub, the printed circuit board in 3D

    Usbhub

    gmarcus1018/Portfolio_Web

    Personal portfolio site built with Astro. Static site, deploys to Cloudflare Pages.

    65 parts
  • 2 layers20.3 × 10.2 mmLsm6dsv32x breakout, the printed circuit board in 3D

    Lsm6dsv32x breakout

    godmar/imuboard-claude

    A minimal breakout for the ST LSM6DSV32X 6-axis IMU (±32 g accel, ±4000 dps gyro). The circuit follows the mode 1 connection diagram in ST's datasheet (DS13511, Figure 28, section 7.1).

    11 parts
  • 2 layers78.7 × 96.5 mmRIO Flexible Breakout, the printed circuit board in 3D

    RIO Flexible Breakout

    GoldbergLab/HeadFixedLickHardware

    Documentation and design files for experimental hardware from the Goldberg Lab head-fixed lick motor control investigation

    2 parts
  • 4 layers32 × 32 mmUSBC UART MODULE, the printed circuit board in 3D

    USBC UART MODULE

    gordgerald-Strat/UART-to-USB-STRATUS-

    UART-to-USB breakout board designed for the soul purpose of being compatible with the small form factor air quality system( STRATUS)

    41 partsMIT
  • 2 layers74.5 × 35.6 mmAdapter HRT902-TPN31A, the printed circuit board in 3D

    Adapter HRT902-TPN31A

    goscickiw/Adapter-HRT902-TPN31A

    Adapter powielacza HRT 902 do montażu w miejscu TPN-31A

    8 partsCC-BY-SA-4.0