Skip to the content
2 layers165 × 42 mmCAN bus distribution board, the printed circuit board in 3D

CAN bus distribution board

geneb/CAN_bus_distribution_board

This CAN bus distribution board is designed to connect up to 8 devices to a CAN-equipped controller.

Size
165 × 42 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
26
Pads
108
Tracks, vias
205, 0
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
23 Jul 2026
Updated
26 Jul 2026

Overview

CAN bus distribution board is an open-source printed circuit board by geneb, from the geneb/CAN_bus_distribution_board repository on GitHub. It is a 2-layer board of 165 × 42 mm with 14 parts on 26 nets, routed with 205 tracks and 0 vias.

It is built around the 54602-908LF. Its parts include 13 connectors and 1 resistor. It belongs with the interfaces and adapters boards of this library.

Main components

1

README

README.md

CAN Bus Distribution Board

This board is part of the CAN bus infrastructure in my F-15C flight simulator project.

The board is designed to allow daisy chaining CAN bus devices via RJ45 cables.

This board is also designed to be daisy chained. The "input" side of the board is on the left end, and the "output" is on the right end.

In a single board configuration, the CAN controller would be attached to the left end of the board and the termination resistor should be active on the controller's tranceiver and on the "output" end of the distribution board.

If the distribution boards are daisy chained, an RJ45 cable would connect from the "output" connector on the first board, to the "input" connector on the second board. The termination resistor jumper should be set on the output end of the last board, and on the controller's tranceiver that's attached to the first distribution board in the chain.

[BOARD DESIGN IS NOT TESTED]

Parts

14
QtyValueFootprintReferences
854602-908LFConnector_RJ:RJ45_Amphenol_54602-x08_HorizontalJ2, J3, J4, J5, J6, J7, J8, J9
1120 OhmResistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_HorizontalR1
1Accessory PowerTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_HorizontalJ12
1CAN INConnector_RJ:RJ45_Amphenol_54602-x08_HorizontalJ1
1CAN OUTConnector_RJ:RJ45_Amphenol_54602-x08_HorizontalJ10
1Device PowerTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_HorizontalJ11
1TerminatorConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ13

Similar boards

  • 2 layers158.8 × 159.8 mm1dcoinctrl, the printed circuit board in 3D

    1dcoinctrl

    hharte/1dcoinctrl

    Western Electric 1D/2D Payphone Controller for Asterisk

    115 parts76MIT
  • 2 layers50.8 × 25.4 mmXiegu MiniMic, the printed circuit board in 3D

    Xiegu MiniMic

    jzkmath/Xiegu-MiniMic

    A Small Microphone for the Xiegu G90, X5105 and X6100 Radios

    22 parts17GPL-2.0
  • 4 layers194 × 94 mmBottom board, the printed circuit board in 3D

    Bottom board

    mod-audio/hw-mod-dwarf

    Hardware project of MOD Dwarf

    319 parts6
  • 4 layers110 × 40 mmBugWiperPCB, the printed circuit board in 3D

    BugWiperPCB

    M-Scholli/BugWiper2_0

    Bug Wiper Controller for Sailplanes Version 2 with ESP32-S3

    115 parts4Apache-2.0
  • 2 layers46 × 46 mmMaiana Blue N2000 v8.2, the printed circuit board in 3D

    Maiana Blue N2000 v8.2

    Haimana/MAIANA_BLUE

    Firmware and hardware materials for the MAIANA-class AIS transponder ecosystem. The design builds on the open MAIANA project (GPL v3, Peter Antypas).

    54 parts3
  • 4 layers85 × 88 mmEmonPi3, the printed circuit board in 3D

    EmonPi3

    openenergymonitor/emon32

    emonPi3 & emonTx6 Hardware

    174 parts3CC-BY-SA-4.0
  • 2 layers137.5 × 51 mmLark, the printed circuit board in 3D

    Lark

    tmshlvck/lark-hw

    Lark PCB

    112 parts3GPL-3.0
  • 4 layers94.9 × 43.2 mmGround Station Telemetry, the printed circuit board in 3D

    Ground Station Telemetry

    cacost12/SDR-Ground-Station-Telemetry-PCB

    Current PCB Revision: 1.0 PCB Part Number: A0005

    57 parts1

Questions

How big is the CAN bus distribution board PCB?

It measures 165 × 42 mm and has 2 copper layers, 1.6 mm thick.

What parts does the CAN bus distribution board use?

14 parts, built around the 54602-908LF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the CAN bus distribution board KiCad files?

From the geneb/CAN_bus_distribution_board repository on GitHub, at the commit this page was made from: the board is CANBus Distribution Board.kicad_pcb and its schematic CANBus Distribution Board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the CAN bus distribution board design in my own project?

Its repository states no licence, so its author keeps all rights: ask geneb before reusing the design.