Skip to the content

Boards using the LP5907MFX-1.8

28 boards

Boards in 25 GitHub repositories, designed in KiCad, that use the LP5907MFX-1.8 by Texas Instruments (-40℃~+125℃@(Tj) 1 1.8V 120mV@(250mA) 12uA 250mA 5.5V 6.5uVrms 82dB@(1kHz) Fixed Positive Under Voltage Lockout、Over Temperature Protection、Enable、Short Circuit Protection SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS). See how each wires it, with its parts, size, README and files; the LP5907MFX-1.8’s symbol, footprint and pinout are on its own page.

  • 4 layers39 × 39 mmOneInchEye, the printed circuit board in 3D

    OneInchEye

    will127534/OneInchEye

    A One Inch CMOS sensor (IMX283) camera board designed for Raspberry Pi

    94 parts355MIT
  • 2 layers28.8 × 19.4 mmUniAmp, the printed circuit board in 3D

    UniAmp

    Gmanmodz/U-AMP

    Application program for LM49450 in C with PIC16LF15324. Digital audio configuration for Wii, PS2, and Dreamcast as well as analog audio input depending on jumper selection

    47 parts27
  • 6 layers69.3 × 111.8 mmFMC MIPI v2, the printed circuit board in 3D

    FMC MIPI v2

    VideoGPU/FMC_MIPI

    FMC card to allow interfacing Xilinx FPGA boards with Jetson TX2 or TX1 via CSI-2 camera interface

    143 parts22
  • 6 layers60.6 × 100 mmGecko5education, the printed circuit board in 3D

    Gecko5education

    logisim-evolution/GECKO5Education

    Openhardware educational platform based on the ideas of the ulx3s and Gecko4Education

    311 parts18MIT
  • 4 layers20.3 × 68.6 mmCarrier, the printed circuit board in 3D

    Carrier

    samlittlewood/caravel_carrier

    Carrier for efabless Caravel chip used for Google/Skywater 130nm shuttle program.

    30 parts18MIT
  • 4 layers38 × 74 mmTympan Rev E, the printed circuit board in 3D

    Tympan Rev E

    Tympan/Tympan_Rev_E_Hardware

    Repository for Tympan Rev E Electronics and case designs

    93 parts14MIT
  • 4 layers48 × 49 mmToF camera VGA, the printed circuit board in 3D

    ToF camera VGA

    lnsru/melexis_VGA_ToF_camera

    PCB design with the new MLX75027 VGA time of flight sensor

    70 parts13
  • 4 layers44.3 × 39 mmGmax4002-breakout, the printed circuit board in 3D

    Gmax4002-breakout

    will127534/gmax4002-breakout

    A basic minimum GMAX4002 breakout board for Raspberry Pi

    142 parts12MIT
  • 4 layers38.5 × 97.6 mmTympan C, the printed circuit board in 3D

    Tympan C

    Tympan/Tympan_Rev_C_Hardware

    Repository for the board files for Tympan Rev C

    82 parts7MIT
  • 4 layers38 × 74 mmTympan Rev F, the printed circuit board in 3D

    Tympan Rev F

    Tympan/Tympan_Rev_F_Hardware

    Tympan Rev F Hardware Design Files

    91 parts7CERN-OHL-P-2.0
  • 4 layers155 × 103 mmMEMLNaut 0 3, the printed circuit board in 3D

    MEMLNaut 0 3

    MusicallyEmbodiedML/MEMLNaut

    138 parts6
  • 4 layers20.3 × 68.6 mmCarrier, the printed circuit board in 3D

    Carrier

    PyFive-RISC-V/pyfive-mpw1-pcb

    Breakout carrier for the MPW1 PyFive chip

    68 parts3MIT
  • 4 layers38 × 74 mmTympan D, the printed circuit board in 3D

    Tympan D

    creare-com/OpenTact

    Open Source Headset

    116 parts2MIT
  • 4 layers19 × 19 mmIMX415, the printed circuit board in 3D

    IMX415

    kuku-199/OpenCamera-Hardware

    This project provides hardware design for camera modules based on the IMX series chips, covering complete design files from schematics to PCB layout.

    36 parts1
  • 4 layers69.8 × 71.5 mmAviyonik, the printed circuit board in 3D

    Aviyonik

    basarbinici/4-Layered-Flight-Controller-PCB

    The board is designed around a high-performance flight-control MCU and uses three independent SPI-connected IMUs for motion sensing.

    133 parts
  • 4 layers38 × 46 mmTympan Nya, the printed circuit board in 3D

    Tympan Nya

    EntropicEngineering/hearing_aid

    Building an open-source hearing aid

    90 parts
  • 2 layers44 × 35.8 mmDesktopToy, the printed circuit board in 3D

    DesktopToy

    KisonHe/DesktopToy-pcb

    44 partsGPL-2.0
  • 4 layers194 × 40 mmRobobouoy V4.0, the printed circuit board in 3D

    Robobouoy V4.0

    pnn69/NicE-Buoy

    This device sails autonome to a given location.

    258 parts
  • 2 layers60 × 42.6 mmEce16, the printed circuit board in 3D

    Ece16

    trhussain/ECE16PCB

    PCB design for ECE16

    68 parts
  • 4 layers18.3 × 25.8 mmTad5212-board, the printed circuit board in 3D

    Tad5212-board

    tsar-boomba/tad5212-board

    Breakout board for TI's TAD5212 DAC+amp IC

    22 partsGPL-3.0
  • 6 layers60.6 × 100 mmCpuAddOn, the printed circuit board in 3D

    CpuAddOn

    logisim-evolution/GECKO5Education

    Openhardware educational platform based on the ideas of the ulx3s and Gecko4Education

    141 parts18MIT
  • 4 layers58.4 × 43.2 mmAudio iface rev2, the printed circuit board in 3D

    Audio iface rev2

    bnahill/audiopulse-embedded

    Miniature DPOAE infant hearing loss screening device

    84 parts3