Skip to the content

Boards using the LD39050PU33R

29 boards

Boards in 28 GitHub repositories, designed in KiCad, that use the LD39050PU33R by STMicroelectronics (-40℃~+125℃@(Tj) 1 200mV@(500mA) 20uA 3.3V 30uVrms 5.5V 500mA 65dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive DFN-6(3x3) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS). See how each wires it, with its parts, size, README and files; the LD39050PU33R’s symbol, footprint and pinout are on its own page.

  • 4 layers350 × 155 mmVentilator, the printed circuit board in 3D

    Ventilator

    RespiraWorks/Ventilator

    Fully-featured ICU ventilator design, optimized for manufacture using commonly available components and free to license.

    788 parts169Apache-2.0
  • 2 layers100 × 65 mmAstroplant AL, the printed circuit board in 3D

    Astroplant AL

    AstroPlant/astroplant-hardware

    Raw data files for hardware PCB's

    102 parts3
  • 4 layers36 × 60 mmSignal generator, the printed circuit board in 3D

    Signal generator

    NidasioAlberto/signal-generator

    Signal Generator with an STM32

    70 parts3
  • 2 layers81.4 × 54.9 mmEeg, the printed circuit board in 3D

    Eeg

    unaldevelopment/8-Channel-Wireless-EEG

    Bu sürümde (V2.0) tespit edilen kritik şema ve PCB tasarım hataları düzeltilmiştir: 1. STM32F446RE Besleme Kısa Devresi Giderildi: Pin 12 (VSSA) ve Pin 63 (VSS) pinlerinin +3.3V'a olan bağlantısı kesilerek GND…

    225 parts3MIT
  • 4 layersRedoubot, the printed circuit board in 3D

    Redoubot

    Avid0s/2627_ESE_Projet_Redoubot

    La facon dont l'implémentation de fonctionnalités sera faite sera la suivante:

    98 parts2
  • 4 layers157.5 × 130 mmJv thesis, the printed circuit board in 3D

    Jv thesis

    JhonVelasquez/Embedded_system_Synchronize_Plant

    Project of a embedded system that synchronizes signals in a plant. There is electronic (PCB) and software design (FreeRTOS for STM32F7).

    233 parts2
  • 4 layers88.1 × 59.4 mmChromapi motherboard v1, the printed circuit board in 3D

    Chromapi motherboard v1

    Mowibox/chromapi_motherboard

    Raspberry Pi control HAT dedicated to the quadruped robot Chromapi.

    139 parts2Apache-2.0
  • 2 layers61 × 63.5 mmGps, the printed circuit board in 3D

    Gps

    Baksi675/gps-hardware

    Hardware for a custom GPS system developed as part of a master’s thesis. Designed to run with the companion firmware (see gps-firmware repository).

    66 parts1
  • 2 layers288.1 × 97.6 mmSimplekeyboard, the printed circuit board in 3D

    Simplekeyboard

    agrantushinsky/simplekeyboard

    164 partsMIT
  • 4 layers150.5 × 54.4 mmYed eye, the printed circuit board in 3D

    Yed eye

    caglarylmz/Personal-PCB-Projects

    This repository includes my personal electronic design projects.

    114 parts
  • 4 layers80 × 55 mmPicknplacepcbV3, the printed circuit board in 3D

    PicknplacepcbV3

    caleboblepias/precision-gantry-control-system

    This project implements the embedded control backbone of an automated pick and place operations. The system centers on a custom STM32F103RB-based PCB running bare-metal firmware for precise motion control of stepper and…

    52 partsMIT
  • 4 layers110 × 122.3 mmWalking spider robot, the printed circuit board in 3D

    Walking spider robot

    DziadekMateusz/Walking_spider_robot_PCB

    Custom control board for a spider robot. Based on the STM32F103C8T6 microcontroller. Features dedicated 5V power supplies for eight servo motors, USB-C programming, Li-Po 2S power input, onboard protection circuits…

    146 parts
  • 4 layers53.9 × 61.7 mmSTM32L476RG, the printed circuit board in 3D

    STM32L476RG

    GauravRDatta/ELEC5882M-project

    1) Gaussnewton5.m : This code performs an iterative non-linear Gauss-newton algebraic method for 3-D localisation of an initial guesstimate tag location near to its true original location within reasonable accuracy.

    60 parts
  • 6 layers14.5 × 90 mmNew stm32u3-203f, the printed circuit board in 3D

    New stm32u3-203f

    IsaacNorris/new-stm32u3-203f-hardware

    hardware design for my stm32 board

    82 parts
  • 2 layers74.4 × 57.6 mmController ckt, the printed circuit board in 3D

    Controller ckt

    juanrortiz/AVL-MARVIN-Controller

    AVL - Fall Cohort 2026

    27 parts
  • 4 layers100 × 50 mmBalancing robot, the printed circuit board in 3D

    Balancing robot

    JwAhn0830/stm32_balancingRobot

    68 parts
  • 2 layers217.3 × 127.3 mmPCB ApiaryWaterDispensingSystem, the printed circuit board in 3D

    PCB ApiaryWaterDispensingSystem

    Mateuszworo97/Projects

    Apiary Water Dispensing System — This is a device design whose purpose is to automatically supply bee water from an underground tank. In hard-to-reach places and with limited access to fresh water.

    255 parts
  • 2 layers91.9 × 38.8 mmSTM PCB, the printed circuit board in 3D

    STM PCB

    pixelpioneeradhil/pcbstm32

    KRONOS is a compact 2-layer STM32F401RE development board designed for embedded-system development, programming, debugging, and general-purpose applications.

    48 parts
  • 6 layers76.4 × 40.1 mmIMU Array, the printed circuit board in 3D

    IMU Array

    S0hamJosh1/16-IMU-FPGA-board

    this repository contains the schematic and routed layout for a IMU array board with 16 IMU's and a FPGA for research purposes.

    97 parts
  • 2 layers55 × 30 mmStm32f070-board, the printed circuit board in 3D

    Stm32f070-board

    suyashsingh/stm32f070-board

    Board design for STM32F070F6 micro-controller.

    39 parts
  • 2 layersCurrent Source flexPCB, the printed circuit board in 3D

    Current Source flexPCB

    wenli-web/Hydrogen-evolution-in-hydrogel-electrochemical-cell

    This is a repository of Flexible PCB control over hydrogen generation device and python code for video and data analysis

    33 parts