4 layers42 × 50 mm
SimpleFC G
wangyeee/OpenHardware
Collections of hardware design related to my drone project.
134 parts10BSD-3-Clause
2 layers100 × 100 mm
ReflowOvenController
wangyeee/OpenHardware10Collections of hardware design related to my drone project.
- Size
- 100 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 102
- Nets
- 85
- Pads
- 292
- Tracks, vias
- 381, 81
- Pours
- 17
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 20 Feb 2016
- Updated
- 29 Jan 2020
Overview
ReflowOvenController is an open-source printed circuit board by wangyeee, from the wangyeee/OpenHardware repository on GitHub, published under the BSD-3-Clause licence. It is a 2-layer board of 100 × 100 mm with 102 parts on 85 nets, routed with 381 tracks and 81 vias.
It is built around the ATMEGA328P-AU, BTA16 and MP1470-MS, with the MAX31855, MOC3020M and H11A1M among its other parts. Its parts include 29 capacitors, 26 resistors, 11 diodes, 10 ICs and 9 connectors. It belongs with the robots and motor control and radio and wireless boards and the STM32 and AVR (ATmega, ATtiny) boards of this library.
Main components
9
ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
BTA16
TO-220E-40℃~+150℃ 1 TRIAC 1.5V 1.65V 160A 16A 1W 50mA 800V TO-220E Thyristors (SCR)/Modules ROHSDongChenTRIACs
MP1470-MS
SOT-23-6-40℃~+85℃ 1 2A 4.5V~21V 400kHz~580kHz Adjustable Buck Buck Built-in Yes SOT-23-6 DC-DC Converters ROHSMSKSEMIDC-DC Converters
MAX31855
UncategorisedMaxim Integrated (Analog Devices)
MOC3020M
DIP-6-40℃~+85℃ 1 1.15V 4.17kV 400V 60mA No TRIAC DIP-6 Triac, SCR Output Optoisolators ROHSonsemiTriac, SCR Output OptoisolatorsH11A1M
PDIP-6-40℃~+100℃ 1.18V 270mW 30V 4.17kV 50% 60mA DC Phototransistor PDIP-6 Transistor, Photovoltaic Output Optoisolators ROHSonsemiOptocouplers - Phototransistor Output
LM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorised
TXS0108EPW
TSSOP-20-40℃~+85℃ 1 1.4V~3.6V 1.65V~5.5V 60Mbps 8 Automatic direction detection、Output enable high-impedance、Integrated pull-up resistor Bidirectional Level translator Push-Pull、Open-drain TSSOP-20 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters
PESD5V0L
DFN1006-2-55℃~+125℃ 1 100W@8/20us 13V 18pF 200nA 5V 8A@8/20us 8V Bidirectional ESD IEC 61000-4-2、IEC 61000-4-5 DFN1006-2 ESD and Surge Protection (TVS/ESD) ROHSApplied PowerESD Protection Devices
README
SimpleFC_G/README.mdSimpleFC_G
The SimpleFCv2 with integrated GPS receiver. Together with its 10 DoF IMU, it has full navigation capability.
WARNING: The PCB design has not been fabricated, Use with caution!
Change List (compare to SimpleFCv2)
- A UBlox ZOE-M8Q GPS receiver is added while external GPS receiver can still be used by changing solder jumpers.
- The onboard DC-DC converter is now MP1470, which supports 2~3s Li-Po.
Software
SimpleFC was originally designed to run modified version of AutoQuad, the source can be found in my fork of AutoQuad. In additional, port for PaparazziUAV is in progress. It will make SimpleFC support both fixwing and rotorcraft.
STM32F4 resource usage
The following table summarizes usage of the MCU, details such as pinout and DMA allocation can be found in the STM32CubeMX design file SimpleFCv2.ioc in the SimpleFCv2 folder.
| MCU Peripheral | Usage |
|---|---|
| ADC1 | battery monitor and two analog inputs |
| CAN2 | CAN bus |
| I2C1 | MMC5883MA magnetometer and EEPROM |
| SDIO | TF card slot |
| SPI1 | ICM20689 gyroscope/accelerometer and MS5611 barometer |
| TIM3, TIM4, TIM12 | 8 channel PWM output |
| UART4, USART2 | RC input, support serial, S.Bus or PPM |
| USART1 | telemetry |
| USART3 | GPS receiver |
| USB | DFU or CDC telemetry |
3D preview
Front
Back
Parts
102| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100nF | STD_SMD:C_0603_HandSoldering | C2, C3, C4, C5, C6, C7, C8, C11, C21, C22 |
| 6 | TEST | PCB_Misc:TESTPAD_SMALL | TP1, TP2, TP3, TP4, TP5, TP6 |
| 5 | 10nF | STD_SMD:C_0603_HandSoldering | C23, C24, C27, C28, C29 |
| 4 | 100 | STD_SMD:R_0603_HandSoldering | R8, R12, R21, R22 |
| 4 | 10K | STD_SMD:R_0603_HandSoldering | R18, R19, R20, R23 |
| 4 | 1N4001 | Diodes_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1, D2, D3, D4 |
| 4 | M3 | Mounting_Holes:MountingHole_3.2mm_M3 | M1, M2, M3, M4 |
| 3 | 1uF | STD_SMD:C_0603_HandSoldering | C12, C14, C15 |
| 3 | 4.7K | STD_SMD:R_0603_HandSoldering | R1, R2, R3 |
| 3 | CONN_01X02 | Connector:MKDS3-2-5.08 | J1, J5, J6 |
| 2 | 10nF | Capacitors_THT:C_Disc_D12.5mm_W5.0mm_P10.00mm | C17, C19 |
| 2 | 330 | STD_SMD:R_0603_HandSoldering | R26, R27 |
| 2 | 360 | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9, R13 |
| 2 | 39 | Resistors_THT:R_Axial_DIN0414_L11.9mm_D4.5mm_P15.24mm_Horizontal | R11, R15 |
| 2 | 470 | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R10, R14 |
| 2 | 47K | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R16, R17 |
| 2 | 50nF | Capacitors_THT:C_Disc_D12.5mm_W5.0mm_P10.00mm | C16, C18 |
| 2 | BTA16 | STD_PTH:TO-220_Vertical | D5, D6 |
| 2 | MAX31855 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U10, U11 |
| 2 | MOC3020M | Housings_DIP:DIP-6_W7.62mm | U7, U8 |
| 2 | PESD5V | STD_SMD:SOT-23 | D7, D9 |
| 2 | XSD1226-362 | HeatsinkExt:XSD1226-362 | HS1, HS2 |
| 1 | 100K | STD_SMD:R_0603_HandSoldering | R4 |
| 1 | 100nF | Capacitors_THT:C_Disc_D12.5mm_W5.0mm_P10.00mm | C20 |
| 1 | 16MHz | MurataResonators:CERALOCK-CSTCE | Y1 |
| 1 | 1A | Fuse_Holders_and_Fuses:Fuse_SMD1206_HandSoldering | F1 |
| 1 | 1K | Inductors_SMD:L_0603_HandSoldering | L1 |
| 1 | 22uF | STD_SMD:C_1206_HandSoldering | C10 |
| 1 | 22uF | STD_SMD:C_0603_HandSoldering | C13 |
| 1 | 4.7nF | STD_SMD:C_0603_HandSoldering | C26 |
| 1 | 4.7uF | STD_SMD:C_0603_HandSoldering | C1 |
| 1 | 40.2K | STD_SMD:R_0603_HandSoldering | R6 |
| 1 | 470uF | Capacitors_THT:CP_Radial_D10.0mm_P5.00mm | C9 |
| 1 | 6.8uH | Choke_SMD:Choke_SMD_Taiyo_NRS50XX-Handsoldering | L2 |
| 1 | 7.68K | STD_SMD:R_0603_HandSoldering | R7 |
| 1 | 75K | STD_SMD:R_0603_HandSoldering | R5 |
| 1 | AT24CS512 | STD_SMD:SOIC-8_3.9x4.9mm_Pitch1.27mm | U4 |
| 1 | ATMEGA328P-AU | Housings_QFP:TQFP-32_7x7mm_Pitch0.8mm | U1 |
| 1 | FAN | Connector:MKDS3-2-5.08 | J3 |
| 1 | GREEN | LEDs:LED_0603 | D10 |
| 1 | H11A1M | Housings_DIP:DIP-6_W7.62mm | U9 |
| 1 | HEATER | Connector:MKDS3-2-5.08 | J2 |
| 1 | LM1117-3.3 | TO_SOT_Packages_SMD:SOT-223 | U6 |
| 1 | M04 | Connector:M04 | J8 |
| 1 | M05 | Connector:M05 | J7 |
| 1 | M08 | Connector:M08 | J9 |
| 1 | MAIN | Connector:MKDS3-2-5.08 | J4 |
| 1 | MP1470 | dc-dc:TSOT23-6 | U5 |
| 1 | NC | STD_SMD:C_0603_HandSoldering | C25 |
| 1 | NC | STD_SMD:R_0603_HandSoldering | R24 |
| 1 | PESD5V | STD_SMD:D_SOD-323_HandSoldering | D8 |
| 1 | RED | LEDs:LED_0603 | D11 |
| 1 | Symbol_HighVoltage_Type2_SlikTop_VerySmall | PCB_Misc:Symbol_HighVoltage_Type2_SilkTop_VerySmall | HV |
| 1 | TXS0108E | Housings_SSOP:TSSOP-20_4.4x6.5mm_Pitch0.65mm | U2 |
Questions
How big is the ReflowOvenController PCB?
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ReflowOvenController use?
102 parts, built around the ATMEGA328P-AU, BTA16, MP1470-MS and MAX31855. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ReflowOvenController KiCad files?
From the wangyeee/OpenHardware repository on GitHub, at the commit this page was made from: the board is ReflowOvenController/ReflowOvenController.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ReflowOvenController design in my own project?
Its repository publishes it under the BSD-3-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from wangyeee/OpenHardware
8- 4 layers50 × 50 mm
SimpleFC
wangyeee/OpenHardware
Collections of hardware design related to my drone project.
128 parts10BSD-3-Clause - 4 layers42 × 50 mm
SimpleFCv2
wangyeee/OpenHardware
Collections of hardware design related to my drone project.
123 parts10BSD-3-Clause - 4 layers36 × 44 mm
Tinyfc core
wangyeee/OpenHardware
Collections of hardware design related to my drone project.
103 parts10BSD-3-Clause - 2 layers24 × 36 mm
LoRaModem
wangyeee/OpenHardware
Collections of hardware design related to my drone project.
48 parts10BSD-3-Clause - 2 layers45 × 30 mm
AirSeneor
wangyeee/OpenHardware
Collections of hardware design related to my drone project.
43 parts10BSD-3-Clause - 2 layers23 × 18 mm
TinyBEC
wangyeee/OpenHardware
Collections of hardware design related to my drone project.
18 parts10BSD-3-Clause - 2 layers40 × 20 mm
MultiOsc
wangyeee/OpenHardware
Collections of hardware design related to my drone project.
16 parts10BSD-3-Clause
Similar boards
- 2 layers40 × 97.9 mm
- 2 layers61.5 × 48.5 mm
- 2 layers44.5 × 35.7 mm
- 2 layers334.6 × 100.2 mm
Lira
AndreaGiulianini/lira
57-key 40% + numpad keyboard: Bluetooth/USB-C, hot-swap MX, RMK/Vial, and a built-in USB sound card (3.5 mm headset jack). Generated from source with KiCad.
233 parts2MIT - 2 layers89.1 × 49.4 mm
- 2 layers100 × 50 mm
- 4 layers90.5 × 68.3 mm
- 2 layers76.2 × 38.1 mm
WgcMax17Uart0805
RetiredBill/Max17841UartPCB
Small printed circuit board based on Maxim MAX17841B chip for talking to MAX17843 chip based designs
128 partsCC-BY-SA-4.0