Skip to the content
1234567891011121314151617181920212223242526272829303132

ATMEGA328P-AU

Microchip TechnologyJLCPCB preferred

-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHS

Part id
microchip/ATMEGA328P-AU
Category
Microcontrollers (MCU, MPU, SOC)
Package
TQFP-32(7x7)
Pins
32
In stock
33,514 at JLCPCB (C14877)
Used on
757 open-source boards

Overview

The ATMEGA328P-AU is a microcontroller made by Microchip Technology in a TQFP-32(7x7) package with 32 pins. -40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHS.

PCBKit's library has its KiCad symbol (MCU_Microchip_ATmega:ATmega328P-A, from KiCad's library) and its footprint (Package_QFP:TQFP-32_7x7mm_P0.8mm, from KiCad's library), ready for a KiCad board. 33,514 are in stock at JLCPCB (part C14877). 757 open-source boards in 594 repositories on GitHub use it.

Symbol

1PD32PD43GND4VCC7XTAL1/PB68XTAL2/PB79PD510PD611PD712PB013PB114PB215PB316PB417PB518AVCC19ADC620AREF22ADC723PC024PC125PC226PC327PC428PC529RESET/PC630PD031PD132PD2
MCU_Microchip_ATmega:ATmega328P-AFrom KiCad's library

Footprint

1234567891011121314151617181920212223242526272829303132
Package_QFP:TQFP-32_7x7mm_P0.8mmFrom KiCad's library

From the datasheet

6
Supply, least
1.8 V · VCC, recommended operating min · p. 1
Supply, most
5.5 V · VCC, recommended operating max · p. 1
Works from
-40 °C · Operating temperature min · p. 1
Works up to
85 °C · Operating temperature max · p. 1
Takes asleep
100 nA · Power-down mode at 1 MHz, 1.8 V, 25 °C · p. 1
Takes asleep
750 nA · Power-save mode including 32 kHz RTC at 1 MHz, 1.8 V, 25 °C · p. 1

What it is and has

21
Core
Atmel AVR 8-bit · p. 1
Throughput
Up to 20 MIPS at 20 MHz · p. 1
Working registers
32 × 8-bit · p. 1
Flash memory
32 KBytes · p. 6
EEPROM
1 KBytes · p. 6
RAM
2 KBytes · p. 6
Memory endurance
10,000 Flash write/erase cycles; 100,000 EEPROM write/erase cycles · p. 1
8-bit timer/counters
2, with separate prescaler and compare mode · p. 1
16-bit timer/counter
1, with separate prescaler, compare mode, and capture mode · p. 1
PWM
6 channels · p. 1
ADC
10-bit, 8 channels in TQFP · p. 1
USART
Programmable serial USART · p. 1
SPI
Master/slave · p. 1
2-wire interface
Byte-oriented, Philips I2C compatible · p. 1
Watchdog
Programmable timer with separate on-chip oscillator · p. 1
Analog comparator
On-chip · p. 1
Reset protection
Power-on reset and programmable brown-out detection · p. 1
Oscillator
Internal calibrated oscillator · p. 1
Sleep modes
Idle, ADC Noise Reduction, Power-save, Power-down, Standby, Extended Standby · p. 1
Programmable I/O
23 lines · p. 1
Speed grades
0–4 MHz at 1.8–5.5 V; 0–10 MHz at 2.7–5.5 V; 0–20 MHz at 4.5–5.5 V · p. 1

Open-source boards using it

757See all 757
  • 2 layers50.5 × 128.5 mmOpenThereminV45, the printed circuit board in 3D

    OpenThereminV45

    GaudiLabs/OpenThereminV4

    Open Source Theremin Instrument

    107 parts249GPL-3.0
  • 2 layers152 × 88 mmRFBitBangSMT, the printed circuit board in 3D

    RFBitBangSMT

    profdc9/RFBitBanger

    A QRP digital transceiver created from readily available parts for off-the-grid maintenance

    271 parts222
  • 2 layers50.2 × 31.2 mmMCU Datalogger, the printed circuit board in 3D

    MCU Datalogger

    futureshocked/KLP4e_MCU-Datalogger

    This is the repository for the "MCU Datalogger" project.

    31 parts138MIT
  • 2 layers34 × 46 mmNfcemu, the printed circuit board in 3D

    Nfcemu

    solosky/nfc-emu

    NFC模拟器

    58 parts117Apache-2.0
  • 2 layers73 × 94 mmSportiduino base, the printed circuit board in 3D

    Sportiduino base

    sportiduino/sportiduino

    Electronic timing system for orienteering and similar outdoor sports events on Arduino

    119 parts78GPL-3.0
  • 2 layers58.9 × 44.2 mmOpenPSX2AmigaPadAdapter, the printed circuit board in 3D

    OpenPSX2AmigaPadAdapter

    SukkoPera/OpenPSX2AmigaPadAdapter

    Playstation to Commodore Amiga/CD32 Controller Adapter

    43 parts69
  • 2 layers60 × 50 mmVx8 gps prototype v2.0, the printed circuit board in 3D

    Vx8 gps prototype v2.0

    4x1md/vx8_gps

    DIY GPS module for Yaesu VX-8DR/VX-8DE handheld transceiver.

    56 parts66MIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ATMEGA328P-AU?

Yes. The symbol is MCU_Microchip_ATmega:ATmega328P-A and the footprint Package_QFP:TQFP-32_7x7mm_P0.8mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ATMEGA328P-AU?

TQFP-32(7x7), with 32 pins. Its footprint is drawn on this page.

Where is the ATMEGA328P-AU datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the ATMEGA328P-AU?

JLCPCB lists it as part C14877, with 33,514 in stock; the sellers' links on this page open their listings.

What can replace the ATMEGA328P-AU?

Parts like it in the library: the ATMEGA48PA-AU by Microchip Technology, the ATMEGA328PB-AU by Microchip Technology, the ATMEGA88PA-AU by Microchip Technology and the ATMEGA168PA-AU by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ATMEGA328P-AU?

757 boards in 594 repositories on GitHub; the most starred are listed on this page, with their KiCad files.