
Nice!nano pcb
Straverk/nice-nano-mesh
PCB for nice!nano board and LoRa LX-LC535 radio module for mesh nets likes meshtastic and meshcore
KiCad boards from 1,297 GitHub repositories tagged “pcb”, the most starred first; open any of them in PCBKit.

Straverk/nice-nano-mesh
PCB for nice!nano board and LoRa LX-LC535 radio module for mesh nets likes meshtastic and meshcore


stuenkels/LendingLibrary-LightingController
PCB designed to toggle lights on or off in a lending library. Based on an ATTINY85

superfansizhe-beep/tscircuit-stm32f302-board
STM32F302R8T6 考核板 —— 用 tscircuit 以 TypeScript 描述原理图与 PCB,9 页分页、4 层板、含完整交付物

Supertiger576/hcb-wifi-rp2040-devboard
An RP2040 devboard created with a guide from Hack Club

Szymon423/Mesa-7i96s-P1-Port-BOB
Isolated I/O breakout board for the Mesa 7i96S P1 (DB25) port – 12× 24 V opto-isolated inputs, 5× SSR outputs, DIN-rail mount. KiCad 10, LinuxCNC.

Szymon423/Silkscreen-UV-Lamp
Tiny USB-C powered UV lamp for curing soldermask on PCBs. 1 W UV LED, 3D-printed enclosure. KiCad 10, open hardware.

TactileVision/CollabJam-PCB
This repository contains KiCAD projects for the tactile display Printed Circuit Board (PCB).


tb8-5/12VAC-Dual-Output-Buck-Power-Supply-PCB
Custom 2-layer KiCad PCB converting 12VAC to regulated 5V and 3.3V outputs using full-wave rectification and synchronous buck converters.


TechnikWeber/STM32G071CBT6-ILI9341
Custom STM32G071 board with an ILI9341 display and demo firmware.

techy-robot/CACKLE-Driver-DRV8213_brushed_Motor_Driver
This is a single motor driver based on the DRV8213RTER Texas Instruments chip. It is capable of 4 amps current in a voltage range of 1.65 to 11 volts.

techy-robot/CACKLE-Driver-DRV8311_Motor_Driver
This is a single brushless motor driver based on the DRV8311 Texas Instruments chip. It is capable of 5 amps current in a voltage range of 3 to 24 volts. It has integrated current sense amplifiers and protection logic.

techy-robot/CACKLE-Expansion-Sensor_Board
This is a connector breakout board for vertical mezzanine connectors on a hub. It has one Qwiic connector, two nanoSPI connectors, and header breakouts for the free pins, chip select pins, and the SPI pins.

techy-robot/CACKLE-Hub-ESP32-S3
4 port 2 sensor ESP32-S3 control hub. This is part of a modular control board ecosystem, CACKLE. https://github.com/techy-robot/CACKLE

techy-robot/CACKLE-nanoSPI-MA735_magnetic_encoder
This is a super compact SPI magnetic encoder, with the flex cable being 2.4mm wide and 100mm long, and the tip around 5.6mm diameter. It is quite simple, and supports on shaft or side-shaft mounting with correction.

techy-robot/CACKLE-Passive-Endcap
The only purpose of this is to provide a nice end to the chain. It has rounded corners like the PSU at the beginning, and it also has a 120ohm termination resistor for the RS485 bus.

techy-robot/CACKLE-Passive-Vertical_Sensor_Spacer
This is a simple spacer board to extend the height between the main Hub and the expansion boards

techy-robot/CACKLE-PSU-2s_40A_PSU_and_charger
This is a rather complex power supply unit. It supports USB-C Power Delivery at 9volt 2 amps, and can charge a 2 cell lipo battery. It can pump out 40 amps if the battery supports the current.

techy-robot/CACKLE-PSU-USB_2A_PSU_1side
The main ICs are an mcu, and a 5v 2a switching regulator. The system can theoretically handle 20 volt spikes, but this is mostly meant for 5v output on one side only.

tejaswininagalingam/STM32H7
Design a high-performance embedded real-time control board based on an STM32H7 microcontroller, suitable for high-frequency control loops, deterministic outputs, precision sensing, and high-rate data logging.

thimbleio/hand-turkey
Open source hand turkey printed circuit board project.

thisoldscot/Timegrapher_PreAmp
Through-hole piezo preamplifier board for the Timegrapher Studio - conditions the faint escapement signal for the I2S ADC. KiCad.