
Fridge owl
HeyPCB/fridge-owl
Hoot, the fridge reminder owl: The fridge owl that blinks at you until you've taken your meds and had your water. KiCad 10, heypcb.ai merch.
KiCad boards from 316 GitHub repositories tagged “open-hardware”, the most starred first; open any of them in PCBKit.

HeyPCB/fridge-owl
Hoot, the fridge reminder owl: The fridge owl that blinks at you until you've taken your meds and had your water. KiCad 10, heypcb.ai merch.

HeyPCB/hello-8051
HELLO: a tiny 8051 computer shaped like a 1984 desktop. AT89S52, 32 KB SRAM, 128x64 ST7920 LCD, USB-C. 112 x 158 mm 2-layer KiCad 10 board, DRC clean, firmware that writes hello. Built through HeyPCB's MCP server.

HeyPCB/iris-brainstem
Iris Brainstem: power and servo hub of the Iris robot head. 9 V USB-C PD in, 6 V / 5 A servo rail in stitched copper zones (measured), 5 V rail, half-duplex servo bus with ten ports, speaker amp.

HeyPCB/iris-brow
Iris Brow: forehead sensor strip of the Iris robot head. VL53L1X distance, APDS-9306 light, two I2S microphones 108 mm apart, touch pads, on a brow-shaped board. 2-layer KiCad 10 board, DRC-clean, fab-ready.

HeyPCB/iris-cortex
Iris Cortex: head controller of the Iris robot head. ESP32-S3 (16 MB flash, 8 MB PSRAM), OV2640 eye-camera FPC, iris-ring LED drivers, harness hub.

HeyPCB/iris-ring
Iris Ring: the 18 mm annular LED board behind each iris of the Iris robot head. 12 WS2812-2020 pixels around the camera lens. 2-layer, 0.8 mm KiCad 10 board, DRC-clean, with gerbers, BOM, CPL, STEP and renders.

HeyPCB/kestrel-esc
Kestrel 4in1: 6S 4-in-1 ESC running stock AM32 on four STM32G071s, with 24 CSD18540 FETs, LM5109B drivers and battery current sensing. 48 x 52 mm 6-layer KiCad 10 board, DRC clean, with gerbers, BOM, CPL and STEP.

HeyPCB/kestrel-fc
Kestrel H7: STM32H743 FPV flight controller with ICM-20602 + BMI088, MS5611, 16 MB blackbox, 5 V and switchable 10 V BECs.

HeyPCB/kestrel-gps
Kestrel GPS: u-blox MAX-M10S under a 25 mm ceramic patch with an LIS3MDL compass, for Betaflight, INAV and ArduPilot. 28 x 28 mm 4-layer KiCad 10 board, DRC clean, with gerbers, BOM, CPL and STEP.

HeyPCB/phone-robot
Bolt, the phone stand robot: A little robot that holds your phone, charges it, and peeks over the top to tell you how it's eating. KiCad 10, heypcb.ai merch.

HeyPCB/plant-buddy
Sprout, the plant buddy: A circuit-board sprout that cries a little blue tear when your plant is thirsty. KiCad 10, heypcb.ai merch.

HeyPCB/pomodoro-pal
Pomodoro Pal: A tomato on your desk that keeps you focused for 25 minutes, without your phone. KiCad 10, heypcb.ai merch.

HeyPCB/quack-face
Face board for the Open Duck Mini's head: eye LEDs, projector driver, I2S amp and mic, antenna servos, shaped to the head. 4-layer KiCad 10 board plus printed standoffs, fit-checked in the head CAD.

HeyPCB/ruler-dino
Ruler Dino: The bench ruler that measures, sizes screws and tests your wires. KiCad 10, heypcb.ai merch.

HeyPCB/senswear-kicad
Sens Wear's SensWear smart ring hardware, converted from their Altium design to KiCad 10. Design by Sens Wear (github.com/Sens-Wear/hardware), MIT.

HeyPCB/torch-cat
Torch Cat: Boop the cat's nose and its eyes light up your keyhole. KiCad 10, heypcb.ai merch.

HeyPCB/whisker
Drop-in controller for Petoi's Nybble robot cat running the stock OpenCat firmware: ATmega328P, PCA9685, MPU-6050, USB-C, 3 A buck, protected battery input. 4-layer KiCad 10 board plus printed cradle.

hpralfi/comfoair-esp32
ESP32-Platine, um Zehnder ComfoAir, StorkAir WHR und Wernig G90 über RS232 in Home Assistant einzubinden (ESPHome, ohne Cloud)

HuaqiuOpenHardware/xinghongpai-nearlink-dev-board
Xinghongpai WS63V100/Hi3863 NearLink (SLE) open-source development board with KiCad schematic/PCB, BOM and OpenHarmony examples. 星鸿派星闪开发板。

jaggerzhong/microduck-hub-board
Microduck(飞特 HD1910)无源四路舵机总线 HUB 分线板:23×34 mm、2 层 1.0 mm、4×M2 孔对齐髋舵机外壳;含 Gerber、KiCad 与生成脚本 | Passive 4-port servo bus hub for the Microduck biped

jaimebuildsthings/pit-pyro
DIY handheld tire pyrometer that reads tread temps by zone in one pull.

JamesSilvia20/xiao-garage-door
Make any garage door opener smart with a $5 Seeed XIAO ESP32-C6: open-source PCB (JLCPCB/PCBWay ready), ESPHome firmware for Security+ 1.0/2.0 and dry-contact openers, beginner tutorials, Home Assistant + Apple Home.

JJaroll/MacBerry-Pi
Mod del iMac G3 slot-loading (M5521) con Raspberry Pi 5: PCB maestra unificada, placas individuales (J20, J22, Down Converter), bezel interior y visores 3D. Todo en español.
