
Open-source KiCad boards
233 match “ACS712”Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.
- 2 layers40 × 30 mm

- 2 layers70 × 55 mm

ACS712-module
jkordek1/TVZ-ACS712-Current-sensing-module
PCB module for ACS712, fully Integrated, Hall Effect-Based Linear Current Sensor with 2.1 kVRMS Voltage Isolation and a Low-Resistance Current Conductor.
25 parts - 2 layers38 × 22 mm

Current sensor ACS712
SolderedElectronics/Current-sensor-30A-ACS712-breakout-hardware-design
Hardware design, BOM, gerbers and 3D files for Current-sensor-30A-ACS712-breakout designed by Soldered Electronics.
41 parts - 2 layers

- 2 layers

- 2 layers45 × 30 mm

- 2 layers55 × 65 mm

- 2 layers38 × 22 mm

Current sensor ACS712
SolderedElectronics/Current-sensor-30A-ACS712-breakout-hardware-design
Hardware design, BOM, gerbers and 3D files for Current-sensor-30A-ACS712-breakout designed by Soldered Electronics.
30 parts - 2 layers38 × 22 mm

Current sensor ACS712
SolderedElectronics/Current-sensor-30A-ACS712-breakout-hardware-design
Hardware design, BOM, gerbers and 3D files for Current-sensor-30A-ACS712-breakout designed by Soldered Electronics.
33 parts - 2 layers51.4 × 16.5 mm

- 2 layers43.9 × 29 mm

C64Saver2-addon
bwack/C64-Saver-bwack
C64 Saver v1 and v2 - Overvoltage protection for the C64 and its power brick.
43 parts124 - 2 layers87 × 71 mm

- 4 layers32 × 80 mm

- 2 layers99 × 100 mm

Lipo Storage Discharger 2x
KaeptnBalu/Arduino_Lipo_Storage_Discharger
Arduino controlled lipo battery storage discharger with current measurement and current control
84 parts15 - 2 layers177.8 × 115.6 mm

PCB board
steger123/Lawn-mower-robot
This project is an Open Source initiative to make a fully autonomous robot for grass cutting. Later much bigger stuff.
109 parts11 - 2 layers86.4 × 70.5 mm

Adjustable Load v1.1
kholia/Adjustable-Load-v1.1
Easy + Cost-Effective Variable Electronic Load.
20 parts8 - 2 layers377.2 × 318 mm

Three phase bridge
arcoslab/open-coroco-legacy
COmpliant RObot COntroller is a free software project aiming to create an impedance controller based on a stm32 microcontroller using bldc motors and strain gauges.
105 parts6 - 2 layers50 × 100 mm

- 2 layers150.1 × 100.1 mm

Phase1
erdemcanaz/3-Phase-BLDC-driver
A storyline of designing ~400Watt sensored brushless DC motor driver.
56 parts5 - 2 layers100 × 70 mm

- 2 layers102 × 72 mm

RenewableRegulator MPPT PCB 2017
re-innovation/RenewableRegulator
Charge Regulator Designs for off-grid renewable energy projects. Series. Shunt. MPPT.
58 parts2MIT - 2 layers100 × 50 mm

Carga Electronica
kr4fty/Carga-Electronica-STM32
Desarrollo de un Sistema de Control PID para una Carga Electrónica utilizando un STM32
49 parts1 - 2 layers53.9 × 88 mm

LurCotte
LurCotte/Smart-Home-Electronic-Safety-and-Monitoring-System
Proyek ini bertujuan untuk mengembangkan sistem automasi rumah pintar (Smart Home Automation System) yang dapat memantau dan mengontrol peralatan elektronik secara real-time.
12 parts1 - 2 layers104 × 49 mm

Control
mehmetkara7/DC-Motor-Control
This project demonstrates motor control using an ACS712 current sensor with an Atmega324PB microcontroller. The microcontroller controls the motor speed and direction based on the current measured by the ACS712 sensor.
49 parts1
Parts matching “ACS712”
See them in the parts libraryACS712ELCTR-05B-T
SOIC-8-40℃~+85℃ 1.2mΩ 185mV/A 2.1kVrms 3.5us 5A 5V 80kHz Support SOIC-8 Current Sensors ROHSALLEGROCurrent SensorsACS712ELCTR-20A-T
SOIC-8-40℃~+85℃ 1.2mΩ 100mV/A 2.1kVrms 20A 3.5us 5V 80kHz Support SOIC-8 Current Sensors ROHSAllegro MicroSystems, LLCCurrent SensorsACS712ELCTR-30A-T
SOIC-8-40℃~+85℃ 1.2mΩ 2.1kVrms 30A 50kHz 5V 5us 66mV/A Support SOIC-8 Current Sensors ROHSALLEGROCurrent SensorsACS712ELCTR-05B-T-JSM
SOP-8-40℃~+150℃ 1.5mΩ 120kHz 185mV/A 2.5kVrms 4.5V~5.5V 4us 5A Bidirectional detection、Under-voltage lockout、Power-on reset Support SOP-8 Current Sensors ROHSJSMSEMICurrent Sensors