Skip to the content

Open-source KiCad boards

107,410 boards

Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.

  • 2 layers35.6 × 31.5 mmEsp to rs3232, the printed circuit board in 3D

    Esp to rs3232

    smarthomefans/RS232toESP

    Hardware module convert RS232 to wifi UDP

    21 parts2MIT
  • 2 layers15.6 × 33.9 mmAttiny85 dev board, the printed circuit board in 3D

    Attiny85 dev board

    SMN321/tinyDevboard

    Prototype of a devboard for the ATtiny85

    22 parts2GPL-3.0
  • 4 layers352.3 × 159.3 mmTubender PCB, the printed circuit board in 3D

    Tubender PCB

    smvumbaco/Tubender-FA24

    Generate Hardware - Tubender Fall 2024

    264 parts2
  • 2 layers101.6 × 152.4 mmShotTimer, the printed circuit board in 3D

    ShotTimer

    SnakeDoc/ShotTimer

    A Shot Timer for tracking shot times, splits and more.

    104 parts2MIT
  • 2 layers45 × 45 mmESwitch, the printed circuit board in 3D

    ESwitch

    snalvc/ESwitch

    A high-side N-MOSFET electrical switch module

    23 parts2MIT
  • 2 layers222.6 × 67.2 mmSobek, the printed circuit board in 3D

    Sobek

    snark013/sobek

    40% ortolinear keyboard

    105 parts2CC0-1.0
  • 2 layers52 × 30 mmESP32C6 gasometer, the printed circuit board in 3D

    ESP32C6 gasometer

    sneumeister/Gas-o-Meter2

    Automatically track your (energy) gas consumption based on counter wheel magnet

    13 parts2Apache-2.0
  • 2 layers400 × 30 mmPdu board, the printed circuit board in 3D

    Pdu board

    SniperCZE/sms-gateway

    Open SW/HW 1U SMS gateway based on raspberry pi and SIM800L.

    26 parts2MIT
  • 2 layers104 × 29 mmPowerDistributorMini, the printed circuit board in 3D

    PowerDistributorMini

    SoaringCircuits/PowerDistributorMini

    The board and terminals are designed for a much higher electrical load than should ever be needed in a glider, at least 10 Amps per channel and in total.

    24 parts2
  • 4 layers95 × 56 mmJag v1, the printed circuit board in 3D

    Jag v1

    soerenmeier/jag-board

    Jag board is an attempt to make a pcb which can be used to control different kinds of rc vehicles. At first the focus will be on rc cars, which can be controlled via a web interface and a webcam.

    70 parts2Apache-2.0
  • 4 layers75 × 50 mmDIY SPO2-KiCAD Project, the printed circuit board in 3D

    DIY SPO2-KiCAD Project

    Soham3126/DIY-SPO2-KiCAD-Project

    A low-cost, non-invasive Pulse Oximeter (SpO2) and Heart Rate monitor based on the MAX30102 sensor and Arduino. This project features real-time PPG signal processing, I2C communication, and a custom PCB design for…

    19 parts2
  • 4 layers112 × 57 mmUniversalboxArm1-0, the printed circuit board in 3D

    UniversalboxArm1-0

    Solartraveler/UniversalboxArm

    PCB for experimenting with a STM32

    170 parts2
  • 2 layers177.4 × 174.4 mmLED MATRIX MAX7219, the printed circuit board in 3D

    LED MATRIX MAX7219

    SolderedElectronics/8x8-LED-matrix-Purple-MAX7219-board-hardware-design

    Hardware design, BOM, gerbers and 3D files for 8x8-LED-matrix-Purple-MAX7219-board designed by Soldered Electronics.

    2,212 parts2
  • 2 layers162 × 164 mmGNSS GPS L86-M33 breakout with easyC panel, the printed circuit board in 3D

    GNSS GPS L86-M33 breakout with easyC panel

    SolderedElectronics/GNSS-GPS-L86-M33-breakout-qwiic-hardware-design

    Hardware design, BOM, gerbers and 3D files for GNSS-GPS-L86-M33-breakout-qwiic designed by Soldered Electronics.

    684 parts2
  • 2 layers189.4 × 177.4 mmHall effect sensor analog, the printed circuit board in 3D

    Hall effect sensor analog

    SolderedElectronics/Hall-effect-sensor-breakout-with-analog-output-hardware-design

    Hardware design, BOM, gerbers and 3D files for Hall-effect-sensor-breakout-with-analog-output designed by Soldered Electronics.

    1,348 parts2
  • 2 layers89.2 × 88.4 mmLIN breakout, the printed circuit board in 3D

    LIN breakout

    SolderedElectronics/LIN-Transceiver-NCV7329-MASTER-breakout-hardware-design

    Hardware design, BOM, gerbers and 3D files for LIN-Transceiver-NCV7329-MASTER-breakout designed by Soldered Electronics.

    252 parts2
  • 2 layers177.4 × 202 mmMicro SD breakout, the printed circuit board in 3D

    Micro SD breakout

    SolderedElectronics/microSD-card-reader-breakout-hardware-design

    Hardware design, BOM, gerbers and 3D files for microSD-card-reader-breakout designed by Soldered Electronics.

    1,244 parts2
  • 2 layers177.4 × 211.6 mmPMS7003 sensor adapter, the printed circuit board in 3D

    PMS7003 sensor adapter

    SolderedElectronics/PMS7003-sensor-adapter-hardware-design

    Hardware design, BOM, gerbers and 3D files for PMS7003-sensor-adapter designed by Soldered Electronics.

    2,020 parts2
  • 2 layers190.8 × 193.4 mmEasyC adapter, the printed circuit board in 3D

    EasyC adapter

    SolderedElectronics/qwiic-adapter-hardware-design

    Hardware design, BOM, gerbers and 3D files for qwiic-adapter designed by Soldered Electronics.

    2,044 parts2
  • 2 layers116 × 52 mmBASE, the printed circuit board in 3D

    BASE

    somaBits/somabits.github.io

    On Soma Bits and how to build them.

    27 parts2CC0-1.0
  • 2 layers62.5 × 100 mmCtrl pad, the printed circuit board in 3D

    Ctrl pad

    Somebud0180/Ctrl_pad

    A 3x3 macropad with an encoder and OLED display

    23 parts2
  • 2 layers45 × 100 mmGaggiaBoard V3, the printed circuit board in 3D

    GaggiaBoard V3

    SomeLucky1/CoffeeHat

    Basic espresso machine controls based on Arduino Nano extension board.

    80 parts2CC0-1.0
  • 2 layers169.2 × 98.2 mmPower, the printed circuit board in 3D

    Power

    sonicavionics/4in-power

    99 parts2MIT