

Jag v1
Jag board is an attempt to make a pcb which can be used to control different kinds of rc vehicles. At first the focus will be on rc cars, which can be controlled via a web interface and a webcam.
- Size
- 95 × 56 mm
- Copper layers
- 4
- Thickness
- 4.69 mm
- Parts
- 70
- Nets
- 82
- Pads
- 280
- Tracks, vias
- 584, 112
- Pours
- 17
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 21 Jun 2024
- Updated
- 21 Jun 2024
Overview
Jag v1 is an open-source printed circuit board by soerenmeier, from the soerenmeier/jag-board repository on GitHub, published under the Apache-2.0 licence. It is a 4-layer board of 95 × 56 mm with 70 parts on 82 nets, routed with 584 tracks and 112 vias.
It is built around the ATGM336H-5N31, DRV8837CDSG and LM2576HVS-5, with the AMS1117-3.3, AT24C256CN and LSM6DSR among its other parts. Its parts include 19 capacitors, 15 connectors, 12 resistors, 8 ICs and 4 diodes. It belongs with the STM32 boards of this library.
Main components
6ATGM336H-5N31
SMD,10.1x9.7mm-148dBm -40℃~+85℃ 2.5m 2.7V~3.6V 25mA@3.3V 35s GPS、BDS UART、I2C SMD,10.1x9.7mm GNSS Modules ROHS杭州中科微GNSS ModulesDRV8837CDSG
WSON-8-EP(2x2)-40℃~+85℃ 1 1.8V~7V 1A 1Ω Yes WSON-8-EP(2x2) Brushed DC Motor Drivers ROHSTexas InstrumentsBrushed DC Motor DriversLM2576HVS-5
TO-263-5-40℃~+125℃ 1 4V~60V 52kHz Buck Buck TO-263-5 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAT24C256CN
DIP-8-40℃~+105℃ 1.7V~5.5V 100 Years 1MHz 1mA 1uA 2,000,000 Cycles 256Kbit 500ns、900ns 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C DIP-8 EEPROM ROHSHGSEMIEEPROMLSM6DSR
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 9KB Accelerometer Gyroscope SPI、I2C、MIPI I3C X,Y,Z X,Y,Z ±16g ±4000dps LGA-14(2.5x3) Accelerometers ROHSSTMicroelectronicsAccelerometers
README
README.mdJag Board
Jag board is an attempt to make a pcb which can be used to control different kinds of rc vehicles. At first the focus will be on rc cars, which can be controlled via a web interface and a webcam.
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100nF | Capacitor_SMD:C_0402_1005Metric | C3, C4, C9, C11, C15, C18 |
| 5 | 300 | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R5 |
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2, H3, H4 |
| 2 | 0.1uF | Capacitor_Tantalum_SMD:CP_EIA-3216-10_Kemet-I | C7, C8 |
| 2 | 18pF | Capacitor_SMD:C_0402_1005Metric | C16, C17 |
| 2 | 30pF | Capacitor_SMD:C_0402_1005Metric | C13, C14 |
| 2 | 33K | Resistor_SMD:R_0402_1005Metric | R10, R12 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R6, R7 |
| 2 | Servo 3 Jumper | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP2 |
| 1 | 1.5k | Resistor_SMD:R_0402_1005Metric | R11 |
| 1 | 100uF | Capacitor_SMD:CP_Elec_6.3x5.8 | C1 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C10 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | C6 |
| 1 | 1uF | Capacitor_SMD:C_0402_1005Metric | C12 |
| 1 | 220uF | Capacitor_SMD:CP_Elec_10x10 | C2 |
| 1 | 22uF (tantu) | Capacitor_Tantalum_SMD:CP_EIA-6032-28_Kemet-C | C5 |
| 1 | 33K | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C19 |
| 1 | 47nH | Inductor_SMD:L_0603_1608Metric | L2 |
| 1 | 68uH | jag_board:YSPI1050 | L1 |
| 1 | 7.5K | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | AT24C256C | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U8 |
| 1 | ATGM336H-5N | jag_board:ATGM336H-5N | U3 |
| 1 | Battery | jag_board:Batt Connector | J1 |
| 1 | Battery Con 2 | jag_board:Batt Connector | J2 |
| 1 | Crystal @ 32.768kHz 12.5pF | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y2 |
| 1 | Crystal @ 8MHz 20pF | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | DC Motor 1 | jag_board:Batt Connector | J13 |
| 1 | DRV8837C | Package_SON:WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm | U6 |
| 1 | Debug | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J3 |
| 1 | EEPROM 64K | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | Esc 1 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J11 |
| 1 | Esc 2 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J12 |
| 1 | Ext LED1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | Ext LED2 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | GPS Antenna | jag_board:C434807 | J14 |
| 1 | LED1 | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | LED2 | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | LM2576HVS-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U1 |
| 1 | LOGO | jag_board:jaguar_43mm | G*** |
| 1 | LOGO | jag_board:jaguar | G*** |
| 1 | LSM6DSR | jag_board:LSM6DSR | U2 |
| 1 | Power LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | Raspberry Pie | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J4 |
| 1 | STM32F302C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U7 |
| 1 | Schottky | Diode_SMD:D_SMA | D4 |
| 1 | Servo 1 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | Servo 2 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | Servo 3 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J9 |
| 1 | Servo 4 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J10 |
| 1 | USB C | jag_board:USB_C_MOLEX | J15 |
Similar boards
- 2 layers77 × 57.8 mm

- 2 layers75.5 × 61 mm

- 4 layers100 × 50 mm

- 4 layers100 × 100 mm

X16fpga
eshankiyer/x16-fpga-board
Commander X16-compatible computer on one 100x100 mm 4-layer board: Spartan-6 + iCE40 (official VERA), SDRAM, two expansion slots. KiCad, JLCPCB fab files, Verilog gateware.
224 parts - 4 layers101 × 101 mm

HydroponicFlowerControl
OpenHydroponic/rootmaster
RootMaster is an open-source hydroponics system designed to help you grow plants efficiently using a soilless solution.
260 partsCERN-OHL-W-2.0 - 2 layers100 × 100 mm

Explorer
anyshake/explorer
🌏 Detecting seismic wave using 3 geophones and 3-axis accelerometer, pack & send data to AnyShake Observer over RS232 / RS485 serial.
266 parts100 - 4 layers57.1 × 50 mm

- 4 layers119.2 × 85 mm

Questions
How big is the Jag v1 PCB?
It measures 95 × 56 mm and has 4 copper layers, 4.69 mm thick.
What parts does the Jag v1 use?
70 parts, built around the ATGM336H-5N31, DRV8837CDSG, LM2576HVS-5 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Jag v1 KiCad files?
From the soerenmeier/jag-board repository on GitHub, at the commit this page was made from: the board is pcb-v1/jag-v1.kicad_pcb and its schematic pcb-v1/jag-v1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Jag v1 design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).