Skip to the content

Open-source KiCad boards

107,410 boards

Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.

  • 2 layers100 × 42 mmC100 rev e, the printed circuit board in 3D

    C100 rev e

    jan1s/hw-stm32-nixieclock

    Hardware of stm32f10x based nixieclock project

    51 parts4
  • 2 layers11 × 21.9 mm18650-interlude, the printed circuit board in 3D

    18650-interlude

    Jana-Marie/18650-interlude

    A very simple board to measure the current from a 18650 battery cell for power profiling.

    4 parts4
  • 2 layers68.6 × 73.7 mmLm324 soldering station, the printed circuit board in 3D

    Lm324 soldering station

    JanoVel/lm324_soldering_station

    The KiCad project of the lm324 soldering station described in this post: http://electronics.vlzqz.com/analog-closed-loop-controlled-soldering-station.html

    40 parts4MIT
  • 4 layers100 × 100 mmRsyn1, the printed circuit board in 3D

    Rsyn1

    jaromir-sukuba/rsyn

    Resistance synthesizer

    90 parts4MIT
  • 2 layers259.7 × 96.9 mmThe sirens, the printed circuit board in 3D

    The sirens

    jasonhazel/the-sirens

    38/44/48/56 key split keyboard

    122 parts4CC-BY-4.0
  • 2 layers50.8 × 25.4 mmTimeTimerLight, the printed circuit board in 3D

    TimeTimerLight

    jasonrohrer/jason-rohrer

    A repository for my non-project work.

    16 parts4
  • 2 layers20.3 × 69.9 mmSmartWatchRedux E SMT, the printed circuit board in 3D

    SmartWatchRedux E SMT

    JayesonLS/SmartWatchRedux

    Modern replacements for the DS1216 SmartWatch variants

    6 parts4
  • 2 layers80 × 25 mmOpenSmartFocuser, the printed circuit board in 3D

    OpenSmartFocuser

    jayjar291/OpenSmartFocuser

    OpenSmartFocuser is an open-source telescope focuser project with: - ESP32-S3 firmware (display/menu, motor control, serial command handling) - an INDI driver scaffold for host-side integration - hardware design files…

    9 parts4
  • 2 layers192.3 × 119.6 mmAlipt Keyboard Right, the printed circuit board in 3D

    Alipt Keyboard Right

    JayWhyOkay/splice-split-keyboard

    An experimental split 'Alice' Keyboard (Depreciated)

    88 parts4MIT
  • 4 layers60.5 × 60 mmAmiga RGB video splitter, the printed circuit board in 3D

    Amiga RGB video splitter

    jbilander/Amiga_RGB_video_splitter

    Extend your amiga RGB video signal to two display units - screens, monitors, etc, simultaneously

    36 parts4CC-BY-SA-4.0
  • 4 layers97 × 26.9 mmDenise to FPGA, the printed circuit board in 3D

    Denise to FPGA

    jbilander/Denise_to_FPGA

    A small adapter-board that connects 12-bit RGB, 14 MHz CLK, PIXELSW and SYNC-signals on Denise to a FPGA-board via a 5V-tolerant buffer.

    21 parts4CC-BY-SA-4.0
  • 4 layers38 × 38 mmReGary, the printed circuit board in 3D

    ReGary

    jbilander/ReGary

    A drop in replacement PCB for the Fat Gary chip

    39 parts4CC-BY-SA-4.0
  • 4 layers80 × 30 mmLogic board, the printed circuit board in 3D

    Logic board

    jbush001/HeadphoneGuitarPracticeAmp

    Portable headphone amplifier/effects processor for electric guitar practice.

    55 parts4Apache-2.0
  • 2 layers208.2 × 43.6 mmDuePrint3, the printed circuit board in 3D

    DuePrint3

    jcwebber93/DuePrint3

    Stratasys to Duet 3 Interface Board

    49 parts4
  • 2 layers38.9 × 16.5 mmLPC824 RFM9x, the printed circuit board in 3D

    LPC824 RFM9x

    jdesbonnet/RFMxx_LPC812_PCB

    PCB board to experiment with HopeRF RFM69 and RFM98 radio modules. Uses ARM Cortex-M0+ LPC812 as controller.

    16 parts4
  • 4 layers345 × 213.3 mmBoom-1-Top, the printed circuit board in 3D

    Boom-1-Top

    jdotw/OpInst-Bass-1

    Three-voice analog synth with a digital control surface using CEM3340, AS3320 and similar discrete analog components.

    1,029 parts4
  • 2 layers99.7 × 98.4 mmRemote3, the printed circuit board in 3D

    Remote3

    JeanRenier/Remoting-a-microBIT-X

    A set of ESP32 based controllers to remote a µBIT-X transceiver over the internet

    182 parts4
  • 2 layers50 × 50 mmHuhnix, the printed circuit board in 3D

    Huhnix

    Jeija/huhnix

    Automatic chicken door system with AVR, DCF77 time signal receiver and ESP8266 WiFi module

    32 parts4
  • 2 layers39 × 48.5 mmJenin usb hub, the printed circuit board in 3D

    Jenin usb hub

    jeninh/jeninhub

    A USB hub with 2 USB-A and 2 USB-C slots. Plugs into your laptop's USB-C slot.

    24 parts4
  • 2 layers17.8 × 108 mmRing modulator, the printed circuit board in 3D

    Ring modulator

    jeremymlong/passive_ring_modulator

    9 parts4MPL-2.0
  • 2 layers41.9 × 20.3 mmQspimux jspi1, the printed circuit board in 3D

    Qspimux jspi1

    jevinskie/flash-adapter-pcbs

    Various PCB adapters for flash memories and devices that use them

    8 parts4MIT
  • 2 layers354.5 × 132.5 mmPanels001, the printed circuit board in 3D

    Panels001

    jibonaronno/documentsA

    It is required to change settings using SCLManager.exe when required for new setup.

    308 parts4
  • 2 layers116.8 × 63.5 mmSavekey plus test device, the printed circuit board in 3D

    Savekey plus test device

    JiggleSoft/atari-2600-memory-card-tool

    Atari 2600/7800 memory card (compatible with Atari 2600/7800 Save Key) tools.

    15 parts4