Skip to the content
4 layers60.5 × 60 mmAmiga RGB video splitter, the printed circuit board in 3D

Amiga RGB video splitter

jbilander/Amiga_RGB_video_splitter4

Extend your amiga RGB video signal to two display units - screens, monitors, etc, simultaneously

Size
60.5 × 60 mm
Copper layers
4
Thickness
1.6 mm
Parts
36
Nets
57
Pads
162
Tracks, vias
290, 59
Pours
6
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
19 May 2025
Updated
15 Feb 2026

Overview

Amiga RGB video splitter is an open-source printed circuit board by jbilander, from the jbilander/Amiga_RGB_video_splitter repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 4-layer board of 60.5 × 60 mm with 36 parts on 57 nets, routed with 290 tracks and 59 vias.

It is built around the 74HCT2G17GW, 74HCT2G14GW and 74LVC1GX04GV, with the KMDGX-9S-BS-1 and PJ-320A among its other parts. Its parts include 8 capacitors, 7 resistors, 7 connectors, 4 ICs and 1 crystal. It belongs with the lEDs and displays and retro computing and games boards of this library.

Main components

5

README

README.md

Amiga_RGB_video_splitter

Extend your amiga RGB video signal to two display units - screens, monitors, etc, simultaneously

BOM Rev. C

ReferenceName/ValuePackage/FootprintNotes
U1THS7374IPWRTSSOP-14_4.4x5mm_P0.65mmTHS7374IPWR
U274HCT2G17TSOP-6_1.65x3.05mm_P0.95mmHCT2G17GV125
U374HCT2G14TSOP-6_1.65x3.05mm_P0.95mmHCT2G14GV125
U474LVC1GX04GV X-TAL DRIVERTSOP-6_1.65x3.05mm_P0.95mmLVC1GX04GV125
Y118pF Crystal 28.6363 MHz (NTSC) or 28.375 MHz (PAL)3.2 mm x 2.5 mmECS-286.3-18-33-JEM-TR (NTSC)
ABM8-28.375MHZ-B2-T (PAL)
J1D-SUB DB23DB23_Female-ConnectorFemale 23 PIN DB23
J2DSUB-15-HDHD_Female_HorizontalVGA connector
J39 Pin Mini Din ConnectorRight Angle TH Mini Circular DIN Receptacle9pin Mini Din
J4PJ-320ADIP 3.5mm Headphone Audio Socket 4Pins Audio interfacePJ-320A
J5MSK12D193Pin Slide Toggle Switch Pitch_2.5mmMSK12D19 SMD
J6MSK12D193Pin Slide Toggle Switch Pitch_2.5mmMSK12D19 SMD
J7Right angle Single-Pin Header0.64 mm square pin angledpin for a flylead back to switchable Agnus pin 41 (or its pad on motherboard, e.g. JP4 on A500 Rev.6A)
JP1Solder_JumperSolder Jumper for setting above pin (J7) to either /XCLKEN or OE-signal (inverted /XCLKEN signal).
C1100uF Radial Pitch_2.5mmCapacitor TH Radial_D5.0mm_P2.50mme.g.
ECA-1AM101
ECE-A0JKA101I
Bend down flush to board before soldering
C2-C6Ceramic Capacitor 0.1uF = 100nF0805e.g. CL21B104KACNFNC
C7-C8Multilayer Ceramic Capacitors MLCC - 32pF060306031A320FAT2A for oscillator circuit
RN1-RN275 Ω RES ARRAY 4 Resistors1206CAT16-75R0F4LF
R1330 Ω1206Series resistor on C-sync line
R2-R410k Ω1206
R5Resistor 2.2M Ω0603Resistor in oscillator-circuit
R6Resistor 1k Ω0603Resistor in oscillator-circuit
R7Resistor 150 Ω1206Damping resistor for XCLK out to minimize reflections and ringing
Housing2 x Plastic Shell CoverFor DB23/DB25 plugAliexpress
4 x PinHeaderPinHeader Board Weight/Level Support3-pin 2.54 mm pitch single rowMove the plastic guard to leave ~7.5 mm of pin before soldering in order to hold board in perfect level inside the housing


If you use jumper-wire from JP1-pin then you bridge it either with the left pad or the right pad depending on your setup:

text
1. Motherboard has PAL oscillator and Adapter has NTSC oscillator = bridge JP1-pin with XCLKEN-pad (PAD 1)
2. Motherboard has NTSC oscillator and Adapter has PAL oscillator = bridge JP1-pin with OE-pad (PAD 3)

Please note, using a jumper-wire is completely optional, You can switch ECS Agnus in Early Startup menu or with software such as Degrader and then you only control the external XLCK-crystal enable or disable via the switch on the adaptor. However it can be more convenient to have both tasks controlled from one single switch, hence connecting a jumper-wire.



Suitable SCART-lead to use with the adapter (originally for the SEGA Mega Drive 2, (Genesis 2) with AC coupling inside)
https://www.aliexpress.com/item/1005007360209844.html






Filter OFF vs. Filter ON
With the THS7374's filter activated you can clearly see that the vertical jailbars are gone (right picture).

When ordering from JLCPCB select:

Specify Layer Sequence: Yes

text
L1(Top layer):    F_Cu.gbr
L2(Inner layer1): GND_Cu.gbr
L3(Inner layer2): VCC_Cu.gbr
L4(Bottom layer): B_Cu.gbr

Remove Order Number:

text
Specify a location

This will notify JLC where to put the order number, they will replace the "JLCJLCJLCJLC" silkscreen label.


Parts

36
QtyValueFootprintReferences
50.1uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC2, C3, C4, C5, C6
310kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR2, R3, R4
232pFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC7, C8
2MSS22D18 3Pin Slide Toggle Switch Pitch_2.5mmAmiga_RGB_video_splitter:PinHeader_1x03_P2.5mm_VerticalJ5, J6
2R_Pack04 75 ΩAmiga_RGB_video_splitter:RESCAF80P320X160X60-8NRN1, RN2
1100uF Radial Pitch_2.5mmCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC1
1150Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR7
11kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR6
12.2MResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR5
1330Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1
174HCT2G14Package_SO:TSOP-6_1.65x3.05mm_P0.95mmU3
174HCT2G17Package_SO:TSOP-6_1.65x3.05mm_P0.95mmU2
174LVC1GX04Package_SO:TSOP-6_1.65x3.05mm_P0.95mmU4
1CL=16pFCrystal:Crystal_SMD_SeikoEpson_FA238-4Pin_3.2x2.5mmY1
1Conn_01x01Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalJ7
1DB15_Female_HighDensity_MountingHolesConnector_Dsub:DSUB-15-HD_Female_Horizontal_P2.29x1.98mm_EdgePinOffset3.03mm_Housed_MountingHolesOffset4.94mmJ2
1DB23_Female-ConnectorAmiga_RGB_video_splitter:DSUB-23_Female_EdgeMount_P2.77mmJ1
1KMDGX-9S-BS-1Amiga_RGB_video_splitter:KMDGX9SBS1J3
1PJ-320AAmiga_RGB_video_splitter:PJ-320AJ4
1SolderJumper_3_OpenJumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabelsJP1
1THS7374IPWRPackage_SO:TSSOP-14_4.4x5mm_P0.65mmU1

The 30 most common of 36 parts.

Similar boards

  • 4 layers34.6 × 25 mmAmiga DB23 video adapter, the printed circuit board in 3D

    Amiga DB23 video adapter

    jbilander/Amiga_DB23_video_adapter

    A PCB for creating Amiga SCART or Amiga VGA cables. You can also use this adapter to feed a new clock to the Amiga via XCLK making your machine true PAL/NTSC switchable

    32 parts42CC-BY-SA-4.0
  • 2 layers83.3 × 78.2 mmOdyssey 2 rgb, the printed circuit board in 3D

    Odyssey 2 rgb

    abzman/small-useful-PCBs

    65 parts20Unlicense
  • 4 layers76.3 × 88.1 mmExtra av out, the printed circuit board in 3D

    Extra av out

    marqs85/ossc_pro_hw

    OSSC Pro HW files

    78 parts31CERN-OHL-P-2.0
  • 4 layers78 × 49 mmReAgnus MegAChip, the printed circuit board in 3D

    ReAgnus MegAChip

    jbilander/ReAgnus-MegAChip

    A ReAgnus MegaAChip PCB that takes a Gowin FPGA with embedded PSRAM, a PLCC-84 plug and FET level shifters.

    57 parts33CC-BY-SA-4.0
  • 4 layers160 × 185.5 mmClockV2, the printed circuit board in 3D

    ClockV2

    Raphael-Tibbits/ClockV2

    Crystal oscilator clock project

    99 parts
  • 4 layers64 × 88.6 mmSF500, the printed circuit board in 3D

    SF500

    jbilander/SF500

    Spitfire 500, A low-end 14 MHz Accelerator with IDE and 4/8 MB fast RAM for the Amiga 500.

    52 parts82CC-BY-SA-4.0
  • 2 layers25.4 × 18 mmA500 IDE LED board, the printed circuit board in 3D

    A500 IDE LED board

    jbilander/A500_IDE_LED_board

    Amiga 500 Floppy LED to also Display IDE Activity

    10 parts16CC-BY-SA-4.0
  • 2 layers45 × 15 mmA1200 IDE LED fix board, the printed circuit board in 3D

    A1200 IDE LED fix board

    jbilander/A1200_IDE_LED_fix_board

    A small PCB that fixes the IDE Activity LED always lit problem on the A1200.

    6 parts5CC-BY-SA-4.0

Questions

How big is the Amiga RGB video splitter PCB?

It measures 60.5 × 60 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Amiga RGB video splitter use?

36 parts, built around the 74HCT2G17GW, 74HCT2G14GW, 74LVC1GX04GV and KMDGX-9S-BS-1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Amiga RGB video splitter KiCad files?

From the jbilander/Amiga_RGB_video_splitter repository on GitHub, at the commit this page was made from: the board is KiCad/Amiga_RGB_video_splitter.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Amiga RGB video splitter design in my own project?

Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).