
Boards using the 2N2222A
123 boardsBoards in 100 GitHub repositories, designed in KiCad, that use the 2N2222A by Slkor (-55℃~+150℃ 1 NPN 100MHz 100nA 400 40V 5V 600mA 600mV 625mW NPN TO-92 Bipolar (BJT) ROHS). See how each wires it, with its parts, size, README and files; the 2N2222A’s symbol, footprint and pinout are on its own page.
- 2 layers101.5 × 83 mm

- 2 layers279.4 × 203.2 mm

Z180GDC
lynchaj/rhyophyre
Single Board Computer featuring Zilog Z180 processor and NEC µPD7220 Graphics Display Controller
249 parts12 - 2 layers99.1 × 99.1 mm

QL Qsound10x10
alvaroalea/QL_QsoundQprint_clone
A clone board of the Sound card for the Sinclair QL Computer.
23 parts11 - 2 layers156.5 × 67.5 mm

NixieScanDisplay
profdc9/NixieClock
A Nixie clock that uses IN-14 tubes and very generic components that can be easily sourced.
106 parts10 - 2 layers89.3 × 50 mm

MM58167-ISA RTC
jensma-de/MM58167-ISA-RTC
RTC module for the ISA slot. With schematics, project files in kicad and open source software to drive the clock.
29 parts9 - 2 layers97.6 × 76.8 mm

- 2 layers14.6 × 13.6 mm

Chip and transistor
gidim/e61-gauge
An analog temperature gauge for E61 espresso machines. A custom PCB drives a VID6606 stepper motor gauge needle, reading temperature from an NTC thermistor.
15 parts8 - 2 layers147.2 × 58.3 mm

Li IonBatteryProtection
cnobile2012/Li-IonBatteryProtection
Circuit to protect Li-Ion and Li-Po batteries at the cell level.
81 parts6MIT - 2 layers13 × 1.4 mm

- 2 layers158 × 63 mm

Oven controller
codeThatThinks/oven-controller-hw
A Raspberry Pi Zero-powered PID reflow oven controller -- PCB design files
66 parts5 - 2 layers230.5 × 134.6 mm

- 2 layers

WiFi VirtDisk WemosD1mini
welzel-online/WiFi-VirtDisk
The WiFi-VirtDisk is a network-based storage solution that replaces or supplements the classic SD card approach. The hardware consists of an ESP8266 (D1 mini), which is connected to the SPI port (SD card).
14 parts5GPL-2.0 - 2 layers55.6 × 43.2 mm

BallValveController
hansrune/BallValveController
Ball valve controller for irrigation, water automations and leak prevention. Supports CR05 feedback wiring. Based on ESP32c3. ESPEasy and ESPHome based firmware build instructions included
46 parts4 - 2 layers

CoinPCB
keener2u/CoinPCB
Simple ESP8266 breakout board shaped like a challenge coin. Built to be a hackable extendable board for IOT projects and given out for recognition and to spark staff's imagination.
11 parts4 - 2 layers76.2 × 86.4 mm

- 2 layers34.3 × 40.9 mm

HeatPumpControl
hansrune/HeatPumpControl
ESP32c3 board with IR blaster and serial ports for heat pump control over local WiFi with ESPHome or ESPEasy firmwares
34 parts3 - 2 layers101.5 × 67.8 mm

Danger Monitor System Transmitter
JanClyde05/Danger-Monitor-System
ESP32 Based GPS Tracker System using IMU for Motion Tracking Analysis and NRF24L01 for fast rescue information access
17 parts3 - 2 layers33 × 122.1 mm

PCB V0.6.3
ARTS-Laboratory/In-Situ-Water-Quality-Sensor
An in situ water quality sensor for monitoring water quality
34 parts2CC-BY-SA-4.0 - 2 layers40 × 60 mm

- 2 layers59.7 × 62.2 mm

IBolit ngo kicad
MCMarcusAntony/iBOLIT-1.5
Tools added to this board are: - Logic probe included on Top three pin connector. - Lighting and acoustic signals to identify HIGH and LOW status.
38 parts2 - 2 layers61 × 31 mm

Latch mosfet boite lettres
Phil-dav/mailbox-lora-tracker
Weight-sensing mailbox notifier: Heltec ESP32 + LoRa + HX711 load cells
17 parts2MIT - 2 layers400 × 30 mm

Pdu board
SniperCZE/sms-gateway
Open SW/HW 1U SMS gateway based on raspberry pi and SIM800L.
26 parts2MIT - 2 layers100 × 100 mm

- 2 layers52.5 × 64.8 mm
