
MM58167-ISA RTC
jensma-de/MM58167-ISA-RTC
RTC module for the ISA slot. With schematics, project files in kicad and open source software to drive the clock.

Solar MPPT circuit.
12f675-mppt is an open-source printed circuit board by rasberryrabbit, from the rasberryrabbit/PIC12F675MPPT repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 97.6 × 76.8 mm with 45 parts on 27 nets, routed with 230 tracks and 0 vias.
It is built around the PIC12F629-I/P, LM358N and 1N5822-AP, with the 2N2222A and 2N2907A among its other parts. Its parts include 16 resistors, 9 diodes, 6 capacitors, 5 transistors and 4 connectors. It belongs with the power boards and the PIC boards of this library.
Solar MPPT circuit.
This is simple MPPT for solar panel.
New 3.2 firmware from 16F676 project.
Test is ok as expected. ( jan 18 2019 )
It's 50W limit design. Consider D6,D1,D2,L1 with more high power solar panel.
11 mili-ohm N-ch logic level FET(BUK9511 or BUK9508) used for current sensor. It can replace by 11 mili-ohm or lower Rds-on resistance logic level FET.
Transistor 2N2222A -> BC547 or compatible(reverse pin order)
Transistor 2N2907A -> BC557 or compatible(reverse pin order)
L1 100~330uH
LM358N can replace by other pin-compatible regular OP-AMP. TLC272 is more works better.
D8-D9 used for 3.6v Reference. Each has about 1.8v voltage drop.
Q1 gate voltage is 3.6v. It's depend on FET specification.
Q1, Q2 can skip heat spreader with low POWER Solar panel. No heat with 10W panel.
(Note) Sometimes MPPT stalls no output. It caused by low FET bootstrap voltage.
It's very rare condition. It may fixed by R9 change.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 10k | Resistors_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R3, R11, R13, R16 |
| 4 | 1k | Resistors_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R1, R6, R7, R10 |
| 3 | 100k | Resistors_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R2, R4, R8 |
| 3 | 1N5822A | Diodes_THT:D_DO-201AD_P15.24mm_Horizontal | D1, D2, D6 |
| 3 | LED | LEDs:LED_D4.0mm | D4, D8, D9 |
| 2 | 100u | Capacitors_THT:CP_Radial_D12.5mm_P5.00mm | C1, C3 |
| 2 | 2N2222A | TO_SOT_Packages_THT:TO-92_Inline_Wide | Q3, Q4 |
| 2 | BUK9511-55A127 | TO_SOT_Packages_THT:TO-220-3_Vertical | Q1, Q2 |
| 1 | 0.1u | Capacitors_THT:C_Disc_D7.5mm_W4.4mm_P5.00mm | C4 |
| 1 | 10u | Capacitors_THT:CP_Radial_D12.5mm_P5.00mm | C5 |
| 1 | 1N4007 | Diodes_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D5 |
| 1 | 1N4733A 5.1V | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D7 |
| 1 | 1N5819 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D3 |
| 1 | 2.2k | Resistors_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R9 |
| 1 | 2N2907A | TO_SOT_Packages_THT:TO-92_Inline_Wide | Q5 |
| 1 | 3.3k | Resistors_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R15 |
| 1 | 300k | Resistors_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R5 |
| 1 | 330uH | Inductors_THT:L_Toroid_Vertical_L33.0mm_W17.8mm_P12.70mm_Pulse_KM-5 | L1 |
| 1 | 4.7k | Resistors_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R14 |
| 1 | 4.7u 50v | Capacitors_THT:CP_Radial_D12.5mm_P5.00mm | C2 |
| 1 | 47k | Resistors_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R12 |
| 1 | 47u | Capacitors_THT:CP_Radial_D12.5mm_P5.00mm | C7 |
| 1 | LM358N | Housings_DIP:DIP-8_W7.62mm_LongPads | U2 |
| 1 | LM7805_TO220 | TO_SOT_Packages_THT:TO-220-3_Vertical | U1 |
| 1 | O+ | Connectors:1pin | J3 |
| 1 | O- | Connectors:1pin | J4 |
| 1 | PIC12F629-I/P | Housings_DIP:DIP-8_W7.62mm_LongPads | IC1 |
| 1 | S+ | Connectors:1pin | J1 |
| 1 | S- | Connectors:1pin | J2 |
| 1 | Write OP-AMP DIFF | Buttons_Switches_THT:SW_PUSH_6mm | SW1 |

jensma-de/MM58167-ISA-RTC
RTC module for the ISA slot. With schematics, project files in kicad and open source software to drive the clock.

welzel-online/WiFi-VirtDisk
The WiFi-VirtDisk is a network-based storage solution that replaces or supplements the classic SD card approach. The hardware consists of an ESP8266 (D1 mini), which is connected to the SPI port (SD card).

MCMarcusAntony/iBOLIT-1.5
Tools added to this board are: - Logic probe included on Top three pin connector. - Lighting and acoustic signals to identify HIGH and LOW status.

morris6/Modulo-Two_ARINC-429_Converter
Converting a Modulo-Two Serial Stream to Arinc-429 Serial Words

electricalhog/Discrete_Opamp
Off-the-shelve based FET input opamp designed in ECE5204 and brought to PCB

UAA-F14/PCBs-Design
Power electronics PCB coursework — SCR controller, buck converter, Class D amplifier, DC-AC inverter, and a protected power supply Resources

It measures 97.6 × 76.8 mm and has 2 copper layers, 1.6 mm thick.
45 parts, built around the PIC12F629-I/P, LM358N, 1N5822-AP and 2N2222A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the rasberryrabbit/PIC12F675MPPT repository on GitHub, at the commit this page was made from: the board is 12f675-mppt.kicad_pcb and its schematic 12f675-mppt.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).