2 layers100 × 100 mm
DONUT PAD
adonutartist/Nemos-Hackpad-DONUT-PAD
My macropad that works like a game controller or a gamepad!
29 parts1
Hardware
1,802 boardsKiCad boards from 760 GitHub repositories tagged “hardware”, the most starred first; open any of them in PCBKit.
- 2 layers60 × 39 mm
- 2 layers66 × 58.4 mm
- 2 layers40 × 70 mm
KinetiCoreDC
axpaul/KinetiCoreDC
Compact STM32G0-based DC motor controller board featuring TI DRV8874 H-bridge drivers, RS485 communication, optoisolated I/O, and hardware power protection.
183 parts1CERN-OHL-S-2.0 - 2 layers60.3 × 88.1 mm
BotBattle
butros10games/BattleBot
Remote robot control system built with Python, WebSockets, custom hardware and 3D models.
17 parts1Apache-2.0 - 4 layers65 × 56.5 mm
Tangnano9k kr260-hat
calperxd/tangnano9k-kr260-hat
FPGA HAT for the AMD Kria KR260 based on the Tang Nano 9K (Gowin GW1NR-9, FT2232H, 16-bit parallel link on J21): KiCad 10 schematic, 4-layer PCB and JLCPCB production files
181 parts1 - 2 layers51 × 76 mm
- 2 layers70.7 × 70.7 mm
Whistler mic array
ccc909/Whistler
Open-source 16-channel USB MEMS microphone array: KiCad PCB design, XMOS XU316 (xcore.ai) USB Audio Class 2 firmware with DFU, BOM and JLCPCB-ready production files. CERN-OHL-S.
96 parts1CERN-OHL-S-2.0 - 4 layers100 × 80 mm
Emb multirail smps
CGainsWorks/emb-multirail-smps
Compact multi-output switch-mode power supply in Altium: synchronous buck, boost and LDO stages on a 4-layer board, with loop compensation, thermal analysis and EMC pre-compliance.
79 parts1MIT - 2 layers212.2 × 69 mm
Nullwing pcb
CityRunner/nullwing-keyboard
Through hole mechanical keyboard with rotary encoder
85 parts1 - 4 layers254 × 134.6 mm
Z280-S100
cm68/Z280-S100
16-bit Zilog Z280 CPU card for the IEEE-696 S-100 backplane; glue logic in two ATF1508AS CPLDs
61 parts1CERN-OHL-P-2.0 - 2 layers80 × 85.7 mm
Grouped
DAlexis/gps-timestamper
This will be a hardware project providing GPS timestamping.
118 parts1GPL-3.0 - 2 layers75.2 × 59.6 mm
MyHackpad
Dee-24r/d-pad
The design for my first personal macropad. It contains the schematic and pcb designs, case design, and firmware. My hackpad has 5 keys, a rotary encoder, an OLED dsiplay screen and 3 rgb led lights.
17 parts1 - 2 layers255.5 × 116.4 mm
- 2 layers44 × 33 mm
STM32-USBb
diegomrno/STM32-USBb
Experimental PCB based on an STM32 microcontroller with USB type B
32 parts1 - 2 layers64.9 × 89.1 mm
FV-1 EEPROM flasher hardware
e-zsche/FV-1-standalone-programmer
Standalone programmer for assembling and programming FV-1 programs onto 24LC32A EEPROMS
22 parts1 - 2 layers27.5 × 35.3 mm
PCB 2
Ekips-Prime-Pro/Charger
This is the PCB of the Charger for Spike Prime batteries
20 parts1Apache-2.0 - 2 layers12 × 30 mm
Electric greetings
electricui/electricui-helloboard
Cute arduino compatible development board for introducing people to Electric UI
19 parts1 - 2 layers130.2 × 29.8 mm
- 4 layers82.9 × 53.8 mm
ESP32 IoT Project
EngMeesh/ESP32_IoT_Dev_Board
A custom 4-layer IoT development board based on the ESP32-C3, featuring integrated LiPo battery management, a CP2102N USB-UART bridge, MicroSD support, and onboard environmental/audio sensors for embedded engineering…
92 parts1MIT - 2 layers72 × 100 mm
Teebeutel Expansion
entropia/Teebeutel-Expansion
Teebeutel (eng. Teabag) is an electronic, Entropia themed con-badge for the GPN20, featuring an ESP32 microprocessor running micropython.
759 parts1 - 2 layers72 × 121 mm
Teebeutel
entropia/Teebeutel-Hardware
Teebeutel (eng. Teabag) is an electronic, Entropia themed con-badge for the GPN20, featuring an ESP32 microprocessor running micropython.
201 parts1 - 4 layers15.2 × 30.5 mm
RP2040
EPSILON0-dev/RP2040-Breakout-Board
Minimal RP2040 breakout board with USB Micro-B, 16 MB QSPI flash, boot and reset buttons, and breadboard-friendly GPIO headers.
32 parts1MIT - 2 layers348.5 × 142.5 mm
Keeb
FabioCanavarro/MochaDeck
Full hardware design files for a custom mechanical keyboard. Contains the KiCad schematics, BOMs, and 3D .step files.
165 parts1