2 layers21.6 × 45.7 mm
Interfaces and adapters
7,328 boards- 2 layers27.7 × 44.7 mm
GNICE RF SX1280 TCXO F27- breakout board
jonieboii/Breakout-board-for-G-NiceRF-Lora1280F27-board
This is a simple breakout board designed for the GNice RF LoRa SX1280 module.
6 parts3 - 4 layers50.8 × 83.8 mm
- 2 layers16.5 × 31.8 mm
SX1503-Breakout
jspark311/SX1503-Breakout
A breakout board for the Semtech i2c GPIO expander. The SX1503 is an i2c GPIO expander with support for 16 extra pins, 2 voltage translation banks, and a simple PLD capability.
6 parts3 - 2 layers19.8 × 16 mm
- 2 layers54 × 35 mm
Controller
kamilix2003/Phase-Shifter
Interface for RF phase shifter as part of phased antenna array
67 parts3MIT - 2 layers87.6 × 100.8 mm
EtherKraken
karmakrafts/EtherKraken
A RP3A0 SiP based controller with 34 programmable IOs, Cortex M0 co-processor, 2MB of flash, SPI, I²C, UART and 100Base-T connectivity.
84 parts3Apache-2.0 - 4 layers50.8 × 81.3 mm
Esp32-s3-with ken interface
kawashimaken/general-purpose-ken-interface
A modular, multi-MCU prototyping platform with a unified pin-assignment standard and horizontally-stackable expansion boards.
41 parts3MIT - 2 layers50.4 × 50.4 mm
Bluepill ethernet
kellerkindt/bluepill_sensor
Bluepill stm31f103 ethernet sensor extension board with SW written in Rust
47 parts3Apache-2.0 - 4 layers60 × 60 mm
Neo Geo Adapter
kuro68k/Neo-Geo-Adapter
Connect Sega Saturn and Playstation controllers to a Neo Geo
32 parts3GPL-3.0 - 4 layers53 × 32 mm
Ubiquitous waddle
leonwip/ubiquitous-waddle
Dual channel CANnectivity CAN FD to USB-C adapter
44 parts3CERN-OHL-P-2.0 - 4 layers70 × 143 mm
IoBoard
Loic74650/ioBoard
A relay (and more!) board with Ethernet connectivity and MQTT support
206 parts3GPL-3.0 - 2 layers74 × 72 mm
- 2 layers95 × 30 mm
MAP append
MakersAsylumIndia/MAPone
A really bare bones Arduino using ATMega 328P DIP, SPI and Serial Interfaces and a few LEDs. Arduino stripped down to bare basics so everyone can afford it.
47 parts3 - 2 layers30.5 × 17.8 mm
At86rf233-breakout
maribu/at86rf233-breakout
A Breakout Board for the AT86RF233 (Basic Application Schematic in the Datasheet)
22 parts3CC0-1.0 - 2 layers26.7 × 30.6 mm
- 2 layers22 × 26.4 mm
- 2 layers100 × 74 mm
- 2 layers12.7 × 25.4 mm
Mlx90640-breakout
melexis/i2c-stick
Demonstrator for Melexis products with an I2C slave interface.
12 parts3MIT - 4 layers60 × 56 mm
- 2 layers48.7 × 23.9 mm
Md opn2c
Mikejmoffitt/md-opn2c
Adapter for OPN2C (YM3438) use on Megadrive in place of OPN2 (YM2612).
50 parts3 - 4 layers94.3 × 81.8 mm
YukaLink revA
Misaka0x2730/YukaLink
Dual targets USB+ETH ARM JTAG/SWD debugger (BlackMagic port) based on RP2350. JTAG and SWD interfaces are implemented on PIO.
321 parts3GPL-3.0 - 4 layers68.9 × 31.9 mm
TOFE AXIOM adapter
mithro/HDMI2USB-TOFE-AXIOM-adapter
Adapter which allows the expansion cards from the AXIOM be used on a TOFE compatible board.
21 parts3CC-BY-SA-4.0 - 2 layers43 × 26 mm
LIN MFSW Adapter
mka1ugin/LIN_MFSW_Adapter
Аппаратно адаптер выполнен на микроконтроллере STM32F103C8T6, схема и печатная плата разработаны в среде KiCad. Печатная плата односторонняя, габаритные размеры 43 x 26 мм.
29 parts3