Skip to the content

Open-source KiCad boards

107,410 boards

Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.

  • 2 layers80 × 45 mmKerstboom, the printed circuit board in 3D

    Kerstboom

    sensemakersamsterdam/xmas2024

    esp32 software for 2024 xmas tree project

    50 parts2GPL-3.0
  • 2 layers156.8 × 76.8 mm2p3s pwr pack, the printed circuit board in 3D

    2p3s pwr pack

    sensorable/batt-pack

    A 6-cell battery pack for Sensorable Open Source Camera

    25 parts2
  • 2 layers26 × 40 mmNervous ECG, the printed circuit board in 3D

    Nervous ECG

    sensors-inl/Nervous-ECG

    ECAD design files, firmware source code and standalone application for the ECG sensor of the Nervous project.

    65 parts2MIT
  • 2 layers105 × 87 mmStarbie, the printed circuit board in 3D

    Starbie

    Senvor/Starbie

    A tiny motion-controlled digital pet with RGB mood lighting, basically a pocket-sized Tamagotchi. Totally not a Starboy.

    17 parts2
  • 4 layers65.8 × 56.1 mmMosaicG5 RPi HAT, the printed circuit board in 3D

    MosaicG5 RPi HAT

    septentrio-gnss/mosaicG5-HAT

    MosaicG5-HAT: an open source Raspberry Pi HAT based on Septentrio's mosaic-G5

    55 parts2
  • 4 layers22 × 42 mmMoTi, the printed circuit board in 3D

    MoTi

    septentrio-gnss/moTi

    moTi: Is an M.2 Key B open source HW for mosaic G5-T GNSS modules of Septentrio

    30 parts2
  • 2 layers88.8 × 76 mmArch Bridge, the printed circuit board in 3D

    Arch Bridge

    SeraphimlabsLLC/Arch_Bridge

    DCC-EX to Loconet accessory bus interface

    102 parts2AGPL-3.0
  • 2 layers78 × 79 mmNri g13-shifter, the printed circuit board in 3D

    Nri g13-shifter

    serdzz/rp2350-sim800l-ppp

    Embassy firmware for Waveshare RP2350-Plus + SIM800L: AT setup via atat, IP over PPP (embassy-net-ppp), sockets via embassy-net. Optional USB CDC logger.

    38 parts2Apache-2.0
  • 2 layers155 × 140 mmControl board, the printed circuit board in 3D

    Control board

    Sergio5714/experimental-teg-testbed-firmware

    Firmware for STM32 MCU of testbed data acquisition and control system

    89 parts2
  • 2 layers92.1 × 81.2 mmTeste estatico, the printed circuit board in 3D

    Teste estatico

    Serra-Rocketry/thrust-stand

    [Propulsion] Hardware and software to build and operate a rocket motor thrust stand (PCB, sensors, capture code). Does NOT store test data — raw data goes to solid-propulsion or liquid-propulsion.

    11 parts2GPL-3.0
  • 2 layers62 × 58 mmArdustat, the printed circuit board in 3D

    Ardustat

    SeryiBaran/ardustat

    Термостат на Arduino

    16 parts2
  • 2 layers52 × 30 mmCoppertone buffer, the printed circuit board in 3D

    Coppertone buffer

    seunghyukchoe/copper-mcp

    Local-first PCB automation for KiCad with safe MCP tools and deterministic autorouting research.

    26 parts2Apache-2.0
  • 2 layersSold, the printed circuit board in 3D

    Sold

    sevkin/solderino

    паяльник на ардуино (тысячи их)

    11 parts2WTFPL
  • 2 layers66 × 99.7 mmAirMon, the printed circuit board in 3D

    AirMon

    SG-O/airMon

    ESP32 based air quality monitor PCB

    130 parts2CC-BY-4.0
  • 4 layers80 × 40 mmTuner time, the printed circuit board in 3D

    Tuner time

    SG295/ece477_guitartuner

    Automatic Guitar Tuner Project for ECE477 (Senior Design) @ Purdue University

    112 parts2
  • 2 layers145 × 98 mmStmshieldfull, the printed circuit board in 3D

    Stmshieldfull

    sgenomics/pcbs

    There are my personal PCBs... contact me for licensing information.

    178 parts2
  • 2 layers55 × 40 mmE900M30S shield, the printed circuit board in 3D

    E900M30S shield

    sgofferj/E900M30S-shield

    Breakout board for eByte E22 SPI modules with CM4 footprint

    5 parts2CC-BY-SA-4.0
  • 2 layers30.7 × 34.9 mmKnoepfchen, the printed circuit board in 3D

    Knoepfchen

    shack/knoepfchen

    A small PCB with debounced buttons and switch to put on breadboards

    16 parts2MIT
  • 2 layers96.8 × 181.5 mmShadystake, the printed circuit board in 3D

    Shadystake

    Shadytel/shadystake

    40 parts2
  • 4 layers70.8 × 110 mmPipes sub, the printed circuit board in 3D

    Pipes sub

    shannon-greenlight/pipes

    8 Harmonic tracking oscillator

    303 parts2
  • 2 layers21 × 128 mmMosaic x3, the printed circuit board in 3D

    Mosaic x3

    shashwtd/mosaic-x3

    Imagine if github contribution chart came to life as a frame which you could hang on your wall for decor. This is mosaic, you plug it in, connect your github account and tadaaa you now have a frame that mimicks your…

    34 parts2
  • 2 layers40.6 × 33 mmQwiic GPS RTK - ublox NEO M8P, the printed circuit board in 3D

    Qwiic GPS RTK - ublox NEO M8P

    shaun-lloyd/dev-ardupilot-obal

    ArduPi is an open hardware Raspberry Pi hat to run Ardupilot.

    103 parts2CC0-1.0
  • 2 layers102 × 92 mmMacropad, the printed circuit board in 3D

    Macropad

    Sheepy3/Sheepypad

    open source Macropad for art, gaming... whatever you want, man.

    16 parts2GPL-3.0