Skip to the content

Open-source KiCad boards

107,410 boards

Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.

  • 4 layers71.9 × 91 mmKlipper, the printed circuit board in 3D

    Klipper

    tobetter/3DPrinterShield

    "3D Printer Shield" is a board to run 3D printer using ODROID single board computer, technically this board is designed to control the motor driver modules with TMC2209 (UART) or TMC2130 (SPI) through the on-board GPIO…

    111 parts4GPL-3.0
  • 2 layers16 × 8.5 mmBuckboost, the printed circuit board in 3D

    Buckboost

    TobleMiner/LiIon-buck-boost-3V3

    Simple full voltage range single cell LiIon to 3.3 V buck-boost converter

    8 parts4MIT
  • 2 layers58.9 × 25.6 mmLTC4162-board, the printed circuit board in 3D

    LTC4162-board

    TobleMiner/smol-mppt

    A tiny, LTC4162 based MPPT multi-chemistry* charger

    71 parts4
  • 4 layers70 × 50 mmSkibidi phone usb hub, the printed circuit board in 3D

    Skibidi phone usb hub

    tobycm/skibidi-phone-usb-hub

    a very skibidi usb hub for my google pixel 7. powered by the fe1.1s, providing 1 upstream usb c port, 2 downstream usb c ports, and 2 downstream usb a ports!!

    34 parts4MIT
  • 2 layers63.5 × 44.5 mmMidi bff, the printed circuit board in 3D

    Midi bff

    todbot/qtpy_midibff

    QTPy MIDI BFF

    18 parts4GPL-3.0
  • 2 layers27.9 × 41.7 mmModbus Adapter, the printed circuit board in 3D

    Modbus Adapter

    tomasmcguinness/esp32-modbus-serial-adapter

    The hardware folder contains a KiCad PCB design, designed around the ESP32-C6-MINI-1. Both the antenna and non-antenna (U1) versions will work here due to the location of the ESP32.

    23 parts4
  • 2 layers50 × 50 mmM5 Moter, the printed circuit board in 3D

    M5 Moter

    tomorrow56/M5Stack_Motor_Driver

    27 parts4GPL-3.0
  • 2 layers50 × 50 mmM5 PowerSw, the printed circuit board in 3D

    M5 PowerSw

    tomorrow56/M5Stack_Power_Switch

    Add a physical switch to disconnect the battery.

    18 parts4MIT
  • 2 layers33 × 23.9 mmESPTiny1614, the printed circuit board in 3D

    ESPTiny1614

    tomtor/ESPTiny

    KiCad ATtiny84/x14/x02 (SMD) and ESP-01 (ESP 8266) PCB boards

    24 parts4GPL-3.0
  • 2 layers40.5 × 21 mmSingle sided radio interface, the printed circuit board in 3D

    Single sided radio interface

    tomwardill/cm108radiowidget

    A CM108 based widget for interacting with radios via software

    23 parts4MIT
  • 2 layers100 × 45 mmDMX PWM LED Driver, the printed circuit board in 3D

    DMX PWM LED Driver

    tpanajott/DMX512_LedDimmer

    Wireless DMX512 controller with remote LED driver boards

    57 parts4
  • 4 layers54.4 × 31 mmPoolMonitor, the printed circuit board in 3D

    PoolMonitor

    tpanajott/PoolMonitor

    A pool monitor with accompaning PCB

    28 parts4
  • 4 layers110 × 100 mmFidget, the printed circuit board in 3D

    Fidget

    transistorfet/fidget

    An FPGA board that can interface to the Computie expansion bus using an iCE40HX1K

    99 parts4GPL-3.0
  • 16 layers114.3 × 100 mmPlc77-glitcher, the printed circuit board in 3D

    Plc77-glitcher

    travisgoodspeed/plc77-glitcher

    Port of an antique smart card glitcher to modern Kicad.

    36 parts4
  • 2 layers95 × 85 mmNUC980, the printed circuit board in 3D

    NUC980

    TreeNewbeer/Coonix

    Coonix is a funny project about building a application platform in Allwinner-v3s processor.

    172 parts4
  • 2 layers140 × 47 mmMIXER V2 PCB, the printed circuit board in 3D

    MIXER V2 PCB

    trio09/Mixer_analog_DJB3

    Analogic mixer open hardware 2020

    90 parts4
  • 4 layers149.2 × 113.9 mmZ80, the printed circuit board in 3D

    Z80

    tristanvandeweg/z80

    A z80 based computer, designed from scratch

    128 parts4GPL-2.0
  • 2 layersMcu, the printed circuit board in 3D

    Mcu

    trlsmax/stm32_ccd_camera

    A STM32 CCD camera

    92 parts4GPL-3.0
  • 2 layers20 × 60 mmTs13 dev kit, the printed circuit board in 3D

    Ts13 dev kit

    tropicsquare/devboards

    Repository collects hw resources for development boards which are available for the TROPIC01 chip

    72 parts4
  • 2 layers30.5 × 63.5 mmClassicControllerPico, the printed circuit board in 3D

    ClassicControllerPico

    tt3333/ClassicControllerPico

    Classic Controller Pico is a program that allows Raspberry Pi Pico to be recognized as Wii classic controller.

    12 parts4GPL-3.0
  • 2 layers426.4 × 128.7 mmBackplane, the printed circuit board in 3D

    Backplane

    TU-Darmstadt-APQ/DIN_41612_Backplane

    19″ DIN 41612 Backplane. The basis for all rack mountable electronics used by APQ.

    146 parts4CERN-OHL-W-2.0
  • 4 layers208.4 × 105 mmLogicBoard 3GE Repro, the printed circuit board in 3D

    LogicBoard 3GE Repro

    tullulah/VectrexPCBRepro

    OpenHardware project to reproduce the original PCB of the Vectrex (3GE Revision)

    169 parts4GPL-3.0