Skip to the content

Open-source KiCad boards

107,410 boards

Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.

  • 2 layers69.3 × 80 mmHexy, the printed circuit board in 3D

    Hexy

    sqfmi/hexy

    Hexy by SQFMI

    97 parts10MIT
  • 2 layers55 × 44 mmCff3000-pcb, the printed circuit board in 3D

    Cff3000-pcb

    sre/cff3000-pcb

    CFF3000 GPIO Interface

    22 parts10
  • 2 layers50 × 50 mmI2c tiny usb, the printed circuit board in 3D

    I2c tiny usb

    sre/i2c-tiny-usb

    Customized Fork of Till Harbaums i2c-tiny-usb project

    36 parts10
  • 4 layers225.7 × 88.2 mmPipra, the printed circuit board in 3D

    Pipra

    ssbb/pipra

    30-key low profile electro-capacitive wireless split keyboard.

    202 parts10CERN-OHL-W-2.0
  • 2 layers130 × 75 mmQ17-SIGMA PSU, the printed circuit board in 3D

    Q17-SIGMA PSU

    stefaweb/audio-psu

    Some power supply PCBs I developed.

    84 parts10GPL-3.0
  • 2 layers46.8 × 22.6 mmIdentity disk, the printed circuit board in 3D

    Identity disk

    stoggi/chcon-badge-2018

    Hardware and Firmware for the CHCon 2018 badge

    14 parts10MIT
  • 2 layers37.5 × 97.5 mmDouble gain, the printed circuit board in 3D

    Double gain

    Supermagnum/double-gain

    A small PCB that uses two TL082BCP op amps to amplify a signal from a contact microphone.

    39 parts10CC-BY-4.0
  • 2 layers86 × 44.5 mmKiwi EasyBoardv1.2, the printed circuit board in 3D

    Kiwi EasyBoardv1.2

    SWAT-engineering/kiwi-air-monitor

    Kiwi monitor is an open source CO2/Humidity/Temperature sensor intended for monitoring the quality of the air in a room. Kiwi was created to support teachers with a notification to ventilate their classroom.

    21 parts10GPL-3.0
  • 2 layers22.9 × 63.5 mmEsp rust board, the printed circuit board in 3D

    Esp rust board

    swayerloren/KICAD_ENGINE

    AI-assisted KiCad PCB design workflow for schematics, PCB layouts, DRC, BOM/CPL, and fabrication outputs using Codex or Claude.

    96 parts10MIT
  • 2 layers42 × 42 mmFsk oscillator, the printed circuit board in 3D

    Fsk oscillator

    swharden/QRSS-hardware

    A collection of resources related to QRSS hardware (TX and RX)

    40 parts10
  • 2 layers285 × 94.6 mmNodu, the printed circuit board in 3D

    Nodu

    swiftrax/Nodu

    Universal sixty-percent mechanical keyboard with flex cutouts and minimal layouts. QMK / VIA supported

    130 parts10CC0-1.0
  • 4 layers100 × 100 mmPlantomation V2, the printed circuit board in 3D

    Plantomation V2

    Synthron/Plantomation

    DIY plant watering system

    203 parts10
  • 2 layers143 × 85 mmZf vga, the printed circuit board in 3D

    Zf vga

    tangent3D/Z-FIGHTER

    Homebrew Z80 hobby computer

    62 parts10MIT
  • 2 layers100 × 255.2 mmKombucha, the printed circuit board in 3D

    Kombucha

    Taro-Hayashi/Kombucha2

    キーキャップをつけて完成です。 こちらのファームウェアを書き込んでください。XIAO RP2040のBのスイッチを押す代わりに、XIAO RP2040に一番近いキーを押しながらUSBケーブルを繋ぐことでRPI-RP2のドライブを出すことが出来ます。 - tarohayashikombuchastickstick.uf2 - 後期型向け tarohayashikombuchastickstick.uf2

    84 parts10
  • 2 layers30.5 × 31.8 mmA7800-Mega Adapter, the printed circuit board in 3D

    A7800-Mega Adapter

    tebl/A7800-Mega-Adapter

    Adapter for using a wired Sega Mega Drive/Genesis controller on an Atari 7800.

    8 parts10
  • 2 layers260.6 × 193.1 mmCool936rightv100, the printed circuit board in 3D

    Cool936rightv100

    telzo2000/cool936

    cool936 is a split keyboard with a qaz layout. qazレイアウトの分割キーボードです。

    88 parts10MIT
  • 4 layers43.2 × 43.2 mmAstra, the printed circuit board in 3D

    Astra

    TheScientist101/astra

    An open source, low cost, extensible brushed drone.

    93 parts10
  • 2 layers119.6 × 106.5 mmTapeLooper MainBoard, the printed circuit board in 3D

    TapeLooper MainBoard

    TheSlowGrowth/TapeLooper

    A digital tape looper module for Eurorack or standalone use, built on the Daisy Seed.

    243 parts10
  • 4 layers36 × 46 mmPcb LR1110, the printed circuit board in 3D

    Pcb LR1110

    TheThingsIndustries/generic-node-te

    Generic Node Tracker Edition

    162 parts10
  • 4 layers26.7 × 56.5 mmThe pico sid, the printed circuit board in 3D

    The pico sid

    ThKattanek/the_pico_sid

    This is a MOS-6581 / MOS-8580 replacement on the base from reSID on the raspberry pi picp or rp2040.

    22 parts10GPL-3.0
  • 4 layers53.3 × 21 mmOpen80017a, the printed circuit board in 3D

    Open80017a

    ThomHPL/Open80017a

    Version 0.2 fixes the footprints. It has not yet been assembled or tested.

    52 parts10CERN-OHL-S-2.0
  • 2 layers67 × 44 mmWifiDoorBell D1-mini, the printed circuit board in 3D

    WifiDoorBell D1-mini

    thorsten-l/ESP8266-WiFi-Doorbell-Gateway

    A gateway for your doorbell button ;-)

    15 parts10Apache-2.0