Skip to the content

Boards using the CAT24C256LI

99 boards

Boards in 81 GitHub repositories, designed in KiCad, that use the CAT24C256LI by onsemi (1,000,000 cycles 1.8V~5.5V 100 Years 256Kbit 400kHz 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C PDIP-8 EEPROM ROHS). See how each wires it, with its parts, size, README and files; the CAT24C256LI’s symbol, footprint and pinout are on its own page.

  • 6 layers160 × 100 mmAdrmu6layer, the printed circuit board in 3D

    Adrmu6layer

    marcoreps/ADRmu

    ADR1000 10V standard

    240 parts149
  • 2 layers65 × 56.5 mmHat, the printed circuit board in 3D

    Hat

    worlickwerx/pi-parport

    retro parallel port for raspberry pi

    24 parts78GPL-2.0
  • 2 layersTopBoard, the printed circuit board in 3D

    TopBoard

    Libre-Talk/Wave

    Smart Speaker satellite

    184 parts22
  • 4 layers158.8 × 104.1 mm8-Bit CPU, the printed circuit board in 3D

    8-Bit CPU

    frenchie/8-Bit-Computer

    An 8-Bit Computer

    323 parts20
  • 4 layers205.5 × 152 mmLTC3, the printed circuit board in 3D

    LTC3

    psas/launch-tower

    CAD files and software for the launch tower computer (LTC)

    507 parts19
  • 4 layers91.7 × 66.8 mmPico expansion board, the printed circuit board in 3D

    Pico expansion board

    eamars/RaspberryPi-Pico-Motor-Expansion-Board

    A raspberry pi pico expansion board designed for OpenTrickler project

    68 parts18GPL-3.0
  • 2 layers71.2 × 22.6 mmNullWiiCon v2, the printed circuit board in 3D

    NullWiiCon v2

    nullstalgia/NullWiiCon

    AVR Firmware to convert Nintendo Extension port controllers to USB for use on Switch and PC

    56 parts9GPL-3.0
  • 2 layers88.9 × 88.9 mmKnob v1, the printed circuit board in 3D

    Knob v1

    bmo/tuning-knob-pcboard

    KiCAD PC Board design for a tuning knob that works with Flex Radio SmartSDR, PowerSDR, and RHR. Uses STM32 hardware.

    25 parts7MIT
  • 2 layers65 × 56.5 mmKlipper Fan Hat, the printed circuit board in 3D

    Klipper Fan Hat

    mikepthomas/Klipper-Fan-Hat

    A Raspberry Pi Hat to control additional fans using the Raspberry Pi as a Secondary MCU in Klipper Firmware.

    65 parts7GPL-3.0
  • 2 layers65 × 56 mmPower monitor hat, the printed circuit board in 3D

    Power monitor hat

    rafw87/hardware-modules

    Set of DIY hardware modules.

    53 parts7CC-BY-SA-4.0
  • 2 layers87.9 × 78.1 mmSneak100 main board v2, the printed circuit board in 3D

    Sneak100 main board v2

    Eryk-Mozdzen/minisumo-sneak100

    Autonomous minisumo robot

    144 parts4
  • 2 layers65 × 56 mmPifire main module nopwr, the printed circuit board in 3D

    Pifire main module nopwr

    nebhead/pifire-main-module-nopwr

    This PCB provides a modular approach to building your PiFire Smart Smoker Controller. This board breaks out the many interfaces that are commonly used to support sensors, relays, displays and other devices.

    41 parts4MIT
  • 4 layers40 × 55 mmCopterCat cm4, the printed circuit board in 3D

    CopterCat cm4

    matveylapin/CopterCat_cm4

    Полётный контроллер для стандарта FMU-v6u. Обычно на дронах для программирования устанавливают полётный контроллер, одноплатный компьютер и иногда arduino.

    164 parts3Apache-2.0
  • 4 layers80 × 40 mmStm32g0, the printed circuit board in 3D

    Stm32g0

    stefan-misik/ws2812b-light

    Minimalist Christmas lights using WS2812B LEDs and ATtiny85 or STM32G070

    84 parts3MIT
  • 2 layers94 × 72 mmThermostat, the printed circuit board in 3D

    Thermostat

    mbtown01/frosti

    "Financially Reactive Open Source Thermostat Initiative" (FROSTI), a RaspberryPi-based hardware+software solution

    65 parts2
  • 2 layers71 × 100.1 mmTimemachine, the printed circuit board in 3D

    Timemachine

    TaniWanKenobi/the-time-machine

    Table of Contents About The Project Built With PCB Design Wiring BOM Contact

    60 parts2
  • 2 layers65 × 76 mmRaspi HAT, the printed circuit board in 3D

    Raspi HAT

    4rynv/VacDepoctrl

    Open source firmware for a automation of vacuum systems controlled using Raspberry pi

    36 parts1
  • 4 layers79.7 × 139.5 mmHh2020v1, the printed circuit board in 3D

    Hh2020v1

    badgeteam/hackerhotel-2020-hardware

    Conference badge for Hackerhotel 2020.

    104 parts1
  • 2 layers71.5 × 86.3 mmBatteryPod, the printed circuit board in 3D

    BatteryPod

    cryptoAlgorithm/BatteryPod

    Battery-powered HomePod power supply replacement aka NotHomePod

    41 parts1
  • 4 layers70 × 40 mmLora daq module, the printed circuit board in 3D

    Lora daq module

    danielkm-ee/lora_daq_module

    This board is powered by the Seeed Studios Wio-E5 LoRA module for use with it's designated antenna.

    81 parts1MIT
  • 4 layers54.5 × 80 mmElectronicload, the printed circuit board in 3D

    Electronicload

    GM4AJK/electronicload

    Electronic Load

    64 parts1
  • 4 layers65 × 56 mmDashHat, the printed circuit board in 3D

    DashHat

    michaelyoyo/piDashHat

    Pi Hat for an automotive dashboard

    154 parts1
  • 4 layers243.8 × 170.2 mmAtx040-main pcb, the printed circuit board in 3D

    Atx040-main pcb

    piotr-binkowski/atx040-main-pcb

    136 parts1