

Klipper Fan Hat
A Raspberry Pi Hat to control additional fans using the Raspberry Pi as a Secondary MCU in Klipper Firmware.
- Size
- 65 × 56.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 65
- Nets
- 59
- Pads
- 202
- Tracks, vias
- 459, 6
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 21 Mar 2023
- Updated
- 8 Dec 2023
Overview
Klipper Fan Hat is an open-source printed circuit board by mikepthomas, from the mikepthomas/Klipper-Fan-Hat repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 65 × 56.5 mm with 65 parts on 59 nets, routed with 459 tracks and 6 vias.
It is built around the DS18B20, CAT24C256LI and IRLML6344. Its parts include 20 resistors, 7 diodes, 6 connectors, 5 transistors and 2 ICs.
Main components
3DS18B20
TO-92-55℃~+125℃ 12bit 3V~5.5V 750ms Single-bus ±0.4℃ TO-92 Temperature Sensors ROHSUMWTemperature SensorsCAT24C256LI
PDIP-81,000,000 cycles 1.8V~5.5V 100 Years 256Kbit 400kHz 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C PDIP-8 EEPROM ROHSonsemiEEPROMIRLML6344
SOT-23-55℃~+150℃ 1 N-channel 1.1V 1.3W 29mΩ@4.5V 30V 46pF 5A 6.8nC@4.5V 650pF SOT-23 MOSFETs ROHSGuangdong HottechMOSFETs
README
README.mdKlipper Fan Hat

A Hat to use with the Raspberry Pi as a Secondary MCU in Klipper:
- SKR Pico compatible input for powering the Pi and Serial communication
- 5 Mosfet outputs (with 2 pin JST-XH connectors standard on most fans used on 3D printers)
- Voltage selector jumpers to power each fan from either 5V or VCC supplied by screw terminal
- I2C and 1-Wire and SPI headers for connecting accesories to the Raspberry Pi
- 6 headers connected to General Purpose GPIO pins for accesories such as Filament Run Out Sensors
- On Board DS18B20 Temperature Sensor
Documentation
Documentation and Setup information here
Parts that I sourced for assembly:
- 1206 Capacitor Set Ali Express
- 1206 LEDs Ali Express
- 1206 Resistor Set Ali Express
- 2510 Axial Fan Ali Express
- Blade Fuse Holder Ali Express
- DIP-8 24C32 EEPROM Ali Express
- DIP-8 Socket Ali Express
- IRLML6344TRPBF Mosfets Ali Express
- JST-XH Connector Set Ali Express
- Jumper Caps Ali Express
- KF301 Screw Terminal Ali Express
- M2.5x14 BHCS Ali Express
- Pin Header Set Amazon
- Raspberry Pi Headers and Spacers Amazon
- DS18B20 Temperature Sensor Ali Express
Parts
65| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 4.7k | Resistor_SMD:R_1206_3216Metric | R4, R17, R18, R19, R20, R21, R22 |
| 7 | LED | LED_SMD:LED_1206_3216Metric_ReverseMount_Hole1.8x2.4mm | D1, D2, D3, D4, D5, D6, D7 |
| 5 | 100 | Resistor_SMD:R_1206_3216Metric | R7, R9, R11, R13, R15 |
| 5 | 10k | Resistor_SMD:R_1206_3216Metric | R8, R10, R12, R14, R16 |
| 5 | Conn_01x02 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | FAN1, FAN2, FAN3, FAN4, FAN5 |
| 5 | IRLML6344 | Package_TO_SOT_SMD:TSOT-23 | Q1, Q2, Q3, Q4, Q5 |
| 5 | V Select | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1, JP2, JP3, JP4, JP5 |
| 4 | MountingHole_2.7mm_M2.5 | MountingHole:MountingHole_2.7mm_M2.5 | MH1, MH2, MH3, MH4 |
| 2 | 3.9k | Resistor_SMD:R_1206_3216Metric | R2, R3 |
| 2 | LOGO | LOGO | G***, G*** |
| 1 | 1 Wire | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J4 |
| 1 | 100n | Capacitor_SMD:C_1206_3216Metric | C1 |
| 1 | 1k | Resistor_SMD:R_1206_3216Metric | R1 |
| 1 | CAT24C256 | Package_DIP:DIP-8_W7.62mm | U1 |
| 1 | DS18B20 | Package_TO_SOT_THT:TO-92_Inline | U2 |
| 1 | Fuse | Fuse:Fuseholder_Blade_Mini_Keystone_3568 | F1 |
| 1 | GPIO | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J6 |
| 1 | I2C | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J3 |
| 1 | ID_WP | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | WP1 |
| 1 | J10 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | GPIO23 |
| 1 | J11 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | GPIO24 |
| 1 | J12 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | GPIO25 |
| 1 | J7 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | GPIO20 |
| 1 | J8 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | GPIO21 |
| 1 | J9 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | GPIO22 |
| 1 | SPI | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | Serial | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J2 |
| 1 | Vin | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J1 |
Similar boards
- 2 layers77 × 77 mm

- 2 layers32 × 58 mm

HB UNI Sen CAP MOIST
stan23/myPCBs
Verschiedene Platinen für HomeMatic, AskSinPP und SmartHome
38 parts21 - 2 layers100 × 100 mm

PcbV10
klaus-liebler/labathome
Der kleine Bruder von lab@home. Ermöglicht das Experimentieren mit PT1...PTn-Gliedern, die intern als RC-Kombination (entkoppelt über Operationsverstärker) ausgeführt sind.
221 parts5MIT - 4 layers70 × 70 mm

1.Electronics
I-M-Robotics-Lab/STM32-Quadcopter
Quadcopter design based on STM32F411CEU Blackpill flight controller. Compatible with INAV 6.0 firmware.
57 parts80GPL-3.0 - 2 layers86 × 86 mm

Production
kerikun11/IR-Station
Infrared Remote Controller with ESP8266 WiFi-module. You can control your home appliances with your smartphone or laptop.
128 parts54MIT - 2 layers99.8 × 99.8 mm

Stmbl 5.0
freakontrol/stmbl
THE AUTHORS OF THIS SOFTWARE ACCEPT ABSOLUTELY NO LIABILITY FOR ANY HARM OR LOSS RESULTING FROM ITS USE. IT IS EXTREMELY UNWISE TO RELY ON SOFTWARE ALONE FOR SAFETY.
432 parts53GPL-3.0 - 2 layers55 × 55 mm

LeafNode v3.1
leafai-io/leaf-node-v3.x
Modular node for sensor monitoring and device control in grow environments.
91 parts47 - 2 layers61.4 × 103.3 mm

HB Dis EP-42BW
jp112sdl/HB-Dis-EP-42BW
4.2" ePaper Display mit 10 Tasterkanälen für Homematic
45 parts18
Questions
How big is the Klipper Fan Hat PCB?
It measures 65 × 56.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Klipper Fan Hat use?
65 parts, built around the DS18B20, CAT24C256LI and IRLML6344. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Klipper Fan Hat KiCad files?
From the mikepthomas/Klipper-Fan-Hat repository on GitHub, at the commit this page was made from: the board is KiCad/Klipper Fan Hat.kicad_pcb and its schematic KiCad/Klipper Fan Hat.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Klipper Fan Hat design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).