2 layers81 × 72.8 mm
GPS INS PCB
siddarthiyer/GPS-aided-Inertial-Navigation-System-Module
Upper 6 bits - Module ID - max 0x3F Lower 5 bits - Command ID - max 0x1F CAN ID = (Module ID Default Module ID : 0x200 (Standard)
29 parts2
GPS
61 boardsKiCad boards from 37 GitHub repositories tagged “gps”, the most starred first; open any of them in PCBKit.
- 2 layers80 × 85.7 mm
Grouped
DAlexis/gps-timestamper
This will be a hardware project providing GPS timestamping.
118 parts1GPL-3.0 - 4 layers60 × 31 mm
GarageDoor pro
nikolaus018/garageDoor-pro
ESP32-C3 + GPS board that opens the garage door when you leave and arrive: firmware, KiCad PCB and perfboard build
46 parts1MIT - 2 layers52 × 36.5 mm
- 4 layers20.5 × 23 mm
Ublox breakout
TobleMiner/ublox-M8030-KT-breakout
Breakout for the bare UBX-M8030-KT chip. Supports pin compatible chips from M6, M7 and M8 generations. JLCSMT assembly supported
32 parts1 - 4 layers40.8 × 40.8 mm
- 4 layers61.6 × 95.8 mm
In car dashboard
andreiii04/in-car-dashboard
Custom STM32 in-car telemetry display: G-meter, GPS speed and cabin weather on a 2.8" TFT, with each drive logged to SD.
51 partsMIT - 2 layers65 × 23.5 mm
Picise
ckuhtz/picise
Prototype for a time / location GNSS accessory for a Raspberry Pi 40-pin GPIO.
39 partsCC-BY-SA-4.0 - 2 layers47.5 × 65.5 mm
- 4 layers28 × 28 mm
Kestrel gps
HeyPCB/kestrel-gps
Kestrel GPS: u-blox MAX-M10S under a 25 mm ceramic patch with an LIS3MDL compass, for Betaflight, INAV and ArduPilot. 28 x 28 mm 4-layer KiCad 10 board, DRC clean, with gerbers, BOM, CPL and STEP.
14 partsCERN-OHL-S-2.0 - 4 layers60 × 120 mm
Theoros
Majorwhiskey/gps-lora
Theoros is a USB-C GPS logger and LoRa tracker built on the ESP32-S3. It logs 1 Hz u-blox M10 fixes to microSD, shows status on an OLED and sends AES-128-CCM encrypted position over 868 MHz LoRa.
88 partsCERN-OHL-P-2.0 - 2 layers139.6 × 70 mm
Quectel LC76G
ugo-silato/Quectel_LCx6G_GNSS
Driver for Quectel LC26G, LC26G-T, LC76G and LC86G GNSS modules (GPS, GLONASS, Galileo, BeiDou, QZSS): NMEA, PAIR/PQTM commands, UART or I2C. Tested on LC76G with Arduino Uno R3 and R4.
53 partsMIT - 4 layers52 × 57.8 mm
ZED F9P
Will946/GNSS
u-blox ZED-F9P RTK GNSS breakout board with dual-band L1/L2 reception and centimeter-level positioning accuracy.
65 partsMIT - 2 layers77.5 × 48.3 mm
Vx8 gps prototype v1.0
4x1md/vx8_gps
DIY GPS module for Yaesu VX-8DR/VX-8DE handheld transceiver.
32 parts66MIT - 2 layers43.5 × 43.5 mm
Vx8 gps prototype v3.0
4x1md/vx8_gps
DIY GPS module for Yaesu VX-8DR/VX-8DE handheld transceiver.
33 parts66MIT - 2 layers
- 2 layers28 × 28 mm
- 4 layers53 × 23 mm
SparkFun RTK Facet - External Connector
sparkfun/SparkFun_RTK_Facet
The hardware and enclosure for the popular centimeter level RTK Facet GNSS receiver with built in display.
38 parts23 - 2 layers7.2 × 10 mm
- 6 layers10 × 10 mm
- 2 layers17 × 12 mm
Custom screen
mathieupommery/Keyring-GPSTRACKER
Small gps keyring with a lot of possibilities
18 parts5 - 2 layers17 × 12 mm
Custom screen
mathieupommery/Keyring-GPSTRACKER
Small gps keyring with a lot of possibilities
19 parts5 - 2 layers34.9 × 17.2 mm
Custom screen
mathieupommery/Keyring-GPSTRACKER
Small gps keyring with a lot of possibilities
43 parts5 - 2 layers69.5 × 119 mm
Backplane
Queens-Rocket-Engineering-Team/Avionics-23-26
QRET Avionics hardware, firmware, and documentation for 2023 to 2025.
18 parts4