Skip to the content
2 layers17 × 12 mmCustom screen, the printed circuit board in 3D

Small gps keyring with a lot of possibilities

Size
17 × 12 mm
Copper layers
2
Thickness
1 mm
Parts
18
Nets
14
Pads
75
Tracks, vias
78, 45
Pours
11
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
9 Jun 2024
Updated
27 Oct 2026

Overview

Custom screen is an open-source printed circuit board by mathieupommery, from the mathieupommery/Keyring-GPSTRACKER repository on GitHub. It is a 2-layer board of 17 × 12 mm with 18 parts on 14 nets, routed with 78 tracks and 45 vias.

It is built around the PESD5V0S1UL-QYL and RB521S-30. Its parts include 7 capacitors, 4 resistors, 4 diodes, 2 ICs and 1 connector. It belongs with the radio and wireless boards and the STM32 boards of this library.

Main components

2

README

README.md

Keyring-GPSTRACKER (v12.0)

An ultra-compact, highly integrated modular GPS logger built around the STM32G0B1KE and a custom u-blox MIA-M10Q implementation. This project is designed as a fully functional, wearable GNSS tracker featuring worldwide offline geographical awareness, high-frequency SD card logging, Bluetooth connectivity, extreme power management (2µA shutdown draw), and modular waterproof enclosures.

Key Features

  • Configurable High-Speed Logging: Records tracks directly to the internal MicroSD card in .GPX or .CSV format. The logging frequency is adjustable, supporting real-time capture from 1Hz up to 10Hz.
  • Worldwide Offline Awareness & Navigation: Anywhere in the world, the device can instantly identify the closest city (name, direction, population) or the nearest mountain peak. It provides precise directional pointers by fusing data from the GPS, the MMC5603 compass, and the ICM-42688-P IMU.
  • Topological Barometer Calibration: Future firmware implementation of an offline map of topological elevation points stored on the SD card, allowing ultra-precise, automatic recalibration of the barometer altitude.
  • BLE Smartphone Connectivity: An external DA14531 Bluetooth Low Energy (BLE) module will handle seamless, low-power synchronization and configuration with a smartphone app.
  • Plug & Play USB: Acts as a USB Mass Storage Class (MSC) over USB-C. Simply plug the tracker into a computer to access the MicroSD card and retrieve your tracks without removing the card.
  • Extreme Low Power: Fully active power draw is around ~30mA. In shutdown mode, with only 1 LDO running for the STM32, the system draws just 2µA.

Modular Hardware Ecosystem (4 Custom PCBs)

The project relies on an ecosystem of four custom PCBs (two 6-layer boards and two 2-layer boards) connected via ultra-compact 5-pin board-to-board connectors.

1. Mainboard (6-Layer)

The core of the tracker, engineered to maximize available I/O ports while maintaining a tiny footprint.

  • MCU: STM32G0B1KE (chosen for native USB FS 2.0, ultra-low power shutdown modes, and only 1 VDD pin).
  • Internal Sensors: MMC5603 (compass), ICM-42688-P (IMU), and DPS368 (barometer).
  • Storage & Connectivity: MicroSD card slot operating in SPI mode + external DA14531 BLE module support.
  • Power & Charging: LTC4065 LiPo battery charger with USB-C connector.

v12side v12top

BLE Expansion Module (DA14531)

To keep the mainboard ultra-compact while allowing wireless smartphone communication, wireless connectivity is offloaded to a dedicated mini extension PCB. Connected directly to the back of the mainboard via a board-to-board connector, this add-on integrates the ultra-low-power Renesas DA14531 CodeLess BLE module.

Mainboard Back - Without BLE Module backv12withda14531

2. Custom GNSS Receiver Board (6-Layer)

A custom BGA adaptation of the u-blox MIA-M10Q receiver with a dedicated SAW filter and a top-mounted ceramic patch antenna. Designed as a footprint clone of the PA1010D, but utilizing a far superior engine capable of 10Hz updates across all constellations simultaneously.

gpstop gpsbottom

3. Display & Waterproof Extension Panel (Breakaway 2-Layer PCB)

To optimize manufacturing, all auxiliary modules are designed as a single snap-away (breakaway) panelized 2-layer PCB so they can be produced together in one manufacturing run. Once snapped apart, the panel yields three distinct functional boards:

  • 0.42" OLED Carrier Board: Adapts a 0.42-inch SSD1306 OLED screen to the custom 5/6-pin board-to-board (B2B) connector format. It also breaks out the I2C bus to an external JST SM05B connector and includes an external GPIO breakout for a hardware button.
  • 0.49" OLED Carrier Board: Identical architecture to the 0.42" version (B2B adaptation, JST SM05B I2C breakout, button GPIO), but specifically dimensioned to mount a slightly larger 0.49-inch SSD1306 OLED screen.
  • Waterproof Dive Extension Board: Designed specifically to mount inside the waterproof enclosure for deep-water excursions. It adds a TE Connectivity 30-bar external pressure sensor (effectively turning the tracker into a compact dive computer) and a magnetic Hall-effect switch for contactless power/stop-mode toggling through the solid sealed case.

auxpcbside2 auxpcbside1

Smart Power Architecture

Power is cleanly isolated and distributed via 3 independent ultra-low IQ LDOs, controlled by the MCU:

  • LDO 1 (Always-on / MCU baseline): Powers the STM32 directly. Responsible for the 2µA deep shutdown consumption.
  • LDO 2 (Switched): Dedicated exclusively to the GNSS module.
  • LDO 3 (Switched): Powers the SSD1306 display, the MicroSD card, external sensors (including the BLE module), and internal sensors.

Enclosure System: Standard vs. Waterproof (Dive Mode)

The tracker features a modular, tool-free swap enclosure system depending on your activity:

1. Standard Compact Case

The daily-use enclosure. It is ultra-compact, non-waterproof, and provides direct access to the OLED display, physical buttons, MicroSD card slot, and USB-C port for charging and mass-storage data transfer.

balise

2. Waterproof Dive Case

Similar to a GoPro housing, this heavy-duty case is designed for underwater excursions down to several hundred meters.

  • How it works: You remove the mainboard from the standard case, connect it to the Waterproof Extension Board (with the 30-bar sensor and Hall switch already mounted inside the dive case), turn it on, and seal the enclosure.
  • Note: While in this temporary dive case, USB charging and physical MicroSD card access are blocked to ensure 100% water tightness. Power state is managed entirely through the external magnetic Hall sensor.
watercase1

Open Source

This project is fully open source! Feel free to explore the schematics, layouts, and firmware. If you find this project interesting or build your own, please consider leaving a ⭐ on the repository!

Parts

18
QtyValueFootprintReferences
34.7kResistor_SMD:R_0201_0603MetricR8, R9, R10
3PESD5V0S1UL-QYLsamacsys2:PESD5V0S1ULQYLD2, D5, D6
2100nCapacitor_SMD:C_0201_0603MetricC19, C23
21uCapacitor_SMD:C_0201_0603MetricC14, C15
1100RResistor_SMD:R_0201_0603MetricR13
110uCapacitor_SMD:C_0402_1005MetricC16
12.2uCapacitor_SMD:C_0402_1005MetricC17
14.7uCapacitor_SMD:C_0402_1005MetricC18
1RB521S-30samacsys2:SODFL1608X70ND4
1SM05B-SURS-TF_LF__SN_samacsys2:SM05BSURSTFLFSNJ3
1~samacsys2:ssd1306_5pointU5
1~samacsys2:ssd1306_0.42_fpcU2

More from mathieupommery/Keyring-GPSTRACKER

5
  • 6 layers22.7 × 19 mmHardware V11, the printed circuit board in 3D

    Hardware V11

    mathieupommery/Keyring-GPSTRACKER

    Small gps keyring with a lot of possibilities

    71 parts5
  • 2 layers34.9 × 17.2 mmCustom screen, the printed circuit board in 3D

    Custom screen

    mathieupommery/Keyring-GPSTRACKER

    Small gps keyring with a lot of possibilities

    43 parts5
  • 2 layers17 × 12 mmCustom screen, the printed circuit board in 3D

    Custom screen

    mathieupommery/Keyring-GPSTRACKER

    Small gps keyring with a lot of possibilities

    19 parts5
  • 6 layers10 × 10 mmCustom gps, the printed circuit board in 3D

    Custom gps

    mathieupommery/Keyring-GPSTRACKER

    Small gps keyring with a lot of possibilities

    15 parts5
  • 2 layers7.2 × 10 mmAux flex pcb, the printed circuit board in 3D

    Aux flex pcb

    mathieupommery/Keyring-GPSTRACKER

    Small gps keyring with a lot of possibilities

    15 parts5

Similar boards

  • 2 layers20.3 × 50.8 mmRp2354a micro devboard, the printed circuit board in 3D

    Rp2354a micro devboard

    esehehelp/rp2354a_micro_devboard

    rp2354a micro devboard

    65 partsMIT
  • 4 layers67.6 × 49.5 mmLinux Version Purple, the printed circuit board in 3D

    Linux Version Purple

    raybello/KICAD-PCBs

    Repository for KICAD PCB Designs

    321 parts
  • 2 layers19.2 × 37.1 mmRP ROM, the printed circuit board in 3D

    RP ROM

    Yarnadori/RP-ROM

    35 partsMIT
  • 2 layers80 × 80 mmUser interface, the printed circuit board in 3D

    User interface

    Squantor/DiySolderingStation

    Do it yourself soldering station

    91 parts7MIT
  • 4 layers18.7 × 19.5 mmSAU G0, the printed circuit board in 3D

    SAU G0

    oldgerman/SAU-G0

    迷你低功耗温湿度计,可定时自动唤醒记录数据保存并串口导出文本表格

    95 parts5
  • 4 layers14.8 × 14.6 mmNanoslime, the printed circuit board in 3D

    Nanoslime

    higvr-tony/nanoslime

    【硬件、固件与生产】NanoSlime 超小型 SlimeVR 兼容追踪器:电路板、生产文件与板级固件

    71 partsCERN-OHL-S-2.0
  • 2 layers27.9 × 16.5 mmPowerSSO-24 breakout, the printed circuit board in 3D

    PowerSSO-24 breakout

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    18 parts1.2k

Questions

How big is the Custom screen PCB?

It measures 17 × 12 mm and has 2 copper layers, 1 mm thick.

What parts does the Custom screen use?

18 parts, built around the PESD5V0S1UL-QYL and RB521S-30. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Custom screen KiCad files?

From the mathieupommery/Keyring-GPSTRACKER repository on GitHub, at the commit this page was made from: the board is Hardware/all_pcb_screen_gps/0.42inch/custom_screen.kicad_pcb and its schematic Hardware/DA14531_extension_BLE/aux_flex_pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Custom screen design in my own project?

Its repository states no licence, so its author keeps all rights: ask mathieupommery before reusing the design.