
Adapter relay
rtyle/ping4pow
Monitor (ping) network resources as a condition for powering a connected device.
KiCad boards from 79 GitHub repositories tagged “esphome”, the most starred first; open any of them in PCBKit.

rtyle/ping4pow
Monitor (ping) network resources as a condition for powering a connected device.

rubenbaldewsing/ODROID-H3-mITX-adapter
Adapter board for mounting the ODROID H3(+) onto mITX formfactor. Including onboard LAN management, UART (BIOS) terminal and other features.


akashihi/P11
ESPHome interface for Panasonic air conditioners and heat pumps (CN-CNT)

Atomicbeast101/smart-doorbell
A KiCad-designed smart doorbell PCB that utilizes the existing doorbell transformer to power the board, the doorbell button wiring to detect actions, and controls the chime.

caccia78/PlancH
Open source desk button panel for Home Assistant: ESP32-S3, ESPHome, OLED display, 10 buttons and RGB backlight. KiCad sources, Gerbers and a 3D-printable stand.

Derisis13/es-pir-esence
small pcb for connecting an ESP8266 module to a PIR sensor.

Diode663/ESP32_4-20mA_Sensor
Single-channel industrial 4-20 mA current-loop reader for ESPHome / Home Assistant. ESP32-S3 + INA226, USB-C powered, 24 V loop supply with a constant-current limiter. KiCad 10, generated from Python.

Djuke-DIYAudio/indoor-sensor
Affordable indoor sensor for measuring CO2, temperature, humidity and pressure

dmatscheko/water_kettle
ESP32-S3 running ESPHome on a custom KiCad PCB for the base of a SEVERIN WK 3479 water kettle

hpralfi/comfoair-esp32
ESP32-Platine, um Zehnder ComfoAir, StorkAir WHR und Wernig G90 über RS232 in Home Assistant einzubinden (ESPHome, ohne Cloud)

JamesSilvia20/xiao-garage-door
Make any garage door opener smart with a $5 Seeed XIAO ESP32-C6: open-source PCB (JLCPCB/PCBWay ready), ESPHome firmware for Security+ 1.0/2.0 and dry-contact openers, beginner tutorials, Home Assistant + Apple Home.

KHit6/RF-WiFi-Bridge
A simple hardware design to bridge between 433 MHz devices and WiFi

KHit6/temperator
Smart connected device to measure 8 temperatures and 2 AC currents

Matyas604/Voice-assistant-for-HA
A voice assistant that connects to Home Assistant, allowing you to send and receive voice commands through it. This enables Home Assistant to perform actions based on voice commands.

mikelawrence/ESPHome-Parking-Assistant
Use a TFMini LiDAR module and a RGB light strip so you can park your car in the same spot everytime!

moinsen-dev/open-bed-climate
Open-source, local-first bed climate system: water-cooled/heated mat, standard parts, DIY kits, Home Assistant. Design phase.

Plokkke/sauter-marapi-esphome
ESPHome / Home Assistant pilot wire (fil pilote) controller for the Sauter Marapi tactile towel radiator — KiCad PCB, reverse engineering notes. Study phase, untested.

Plokkke/viessmann-optolink-esphome
ESPHome / Home Assistant Optolink adapter for Viessmann Vitodens 222-W (Vitotronic 200 HO1B): DIY IR interface on an ESP32-C3, through-hole KiCad PCB with mains supply, 3D-printed enclosure.

Qeteshpony/AC-Controller
Universal WiFi-Based remote control for IoT Devices

Qeteshpony/LED-Bar-Controller
Small controller for 2-color LED Bars

r-hmn/micronova_stove_esphome
Project with PCB and Arduino- and ESPHOME-code for reading ARTEL IDRO15 PelletStove

scottdube/deskhack
Reverse-engineered LOGICDATA COMPACT-e-3-VAL (ErgoSwiss hydraulic desk) handset bus: height readback + ESP32/ESPHome control through a $3 optocoupler tap. First public decode of the COMPACT-e-3's 9-bit serial protocol.

scottdube/my-rat-ratgdo
DIY local Security+ 2.0 garage control for Home Assistant — my rat-ratgdo (D1 Mini ESP32) variant: on-board LM2596, battery-backup tap, SHT3x temp/humidity, and a piezo buzzer.