

Wasserkocher
ESP32-S3 running ESPHome on a custom KiCad PCB for the base of a SEVERIN WK 3479 water kettle
- Size
- 59.7 × 127.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 67
- Nets
- 72
- Pads
- 222
- Tracks, vias
- 471, 88
- Pours
- 236
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 7 Jul 2026
- Updated
- 7 Jul 2026
Overview
Wasserkocher is an open-source printed circuit board by dmatscheko, from the dmatscheko/water_kettle repository on GitHub. It is a 2-layer board of 59.7 × 127.3 mm with 67 parts on 72 nets, routed with 471 tracks and 88 vias.
It is built around the ESP32-S3-WROOM-1-N8R2, TUHS3F05 and AZ1117CH-3.3TRG1, with the PCA9306DCTT, TS04-66-50-BK-100-SMT-TR and WS2812B-2020 among its other parts. Its parts include 14 capacitors, 14 resistors, 7 diodes, 7 switches and 3 ICs. It belongs with the home automation and IoT boards and the ESP32 boards of this library.
Main components
12ESP32-S3-WROOM-1-N8R2
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 97mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesTUHS3F05
DIP-6AC-DC Power ModulesCoselAZ1117CH-3.3TRG1
SOT-223-20℃~+125℃@(Tj) 0.003%Vout 1 1.2V@(800mA) 1.35A 10V 3.3V 4mA 70dB@(120Hz) Fixed Over Current Protection、Over Temperature Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsPCA9306DCTT
SM-8-40℃~+85℃ 1 1.2V~3.3V 1.8V~5.5V 2 Automatic direction detection、Output enable high-impedance Bidirectional Level translator Push-Pull、Open-drain SMBus、I2C SM-8 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level ShiftersTS04-66-50-BK-100-SMT-TR
-Tactile SwitchesCUIWS2812B-2020
SMD,2.2x2mm0.6mA 0.84mm 120us 160mcd 200mcd 2kHz 2mm 2mm 300ns 470.4nm 515.6nm 520mcd 5V 622.5nm 800Kbit/s Built-in power-on reset circuit、Built-in power-on reset circuit、Integrated intelligent reverse connection protection function Top-mount SMD,2.2x2mm RGB LEDs(Built-in IC) ROHSWorldsemiRGB LEDs(Built-In IC)ERJ-P08J102V
1206-55℃~+155℃ 1kΩ 660mW Thick Film Resistor ±200ppm/℃ ±5% 1206 Chip Resistor - Surface Mount ROHSPanasonicChip Resistor - Surface MountERJ-8GEYJ512V
1206-55℃~+155℃ 250mW 5.1kΩ Thick Film Resistor ±200ppm/℃ ±5% 1206 Chip Resistor - Surface Mount ROHSPanasonicChip Resistor - Surface MountSTPS2L30A
SMA(DO-214AC)1 Independent 200uA@30V 2A 30V 450mV@2A 75A SMA(DO-214AC) Schottky Diodes ROHSSTMicroelectronicsSchottky DiodesX2P2104KN1B0130120060ES0
插件,P=10mm-40℃~+110℃ 100nF 275V X2 ±10% Plugin,P=10mm Safety Capacitors ROHSSTESafety CapacitorsERJ-8GEYJ104V
1206100kΩ 250mW Thick Film Resistor ±5% 1206 Chip Resistor - Surface Mount ROHSPanasonicChip Resistor - Surface MountMOV-10D561K
插件,P=7.5mm180pF@1kHz 2.5kA 350V 460V 560V 7.5mm 70J 925V 插件,P=7.5mm Varistors ROHSBournsVaristors
README
README.mdSmart Water Kettle
Replacement electronics for the base of a SEVERIN WK 3479 water kettle: an ESP32-S3 running ESPHome on a custom KiCad PCB. It adds precise target temperatures, a keep-warm mode and full Home Assistant integration — and keeps working completely standalone when Wi-Fi or Home Assistant are down.
TODO — open points in the PCB design
- Check that the fuse in the design is the correct one.
- Add an inrush current limiting resistor before the capacitor. (The built prototype has one retrofitted with wires, but the PCB design still needs to be changed accordingly.)
- Add a capacitor relief (discharge) resistor if the power supply does not have one built in.
Donor hardware
The PCB needs a SEVERIN WK 3479 base with
- either the original kettle,
- or (because much more cleanable, beautiful and socket compatible) a GASTROBACK Tea Aroma Plus 42434 kettle.
Conversion
Features
- Target temperature 20–100 °C, adjustable in configurable steps (default 5 °C) or via presets (40 / 60 / 80 / 100 °C). The target survives reboots and power cuts.
- Keep-warm mode with 2 °C hysteresis for a configurable duration (0–15 min, 0 = off).
- Remaining-time estimate from the smoothed heating rate, shown on the display and in Home Assistant.
- Boil detection: when the temperature stagnates above 65 °C the water is boiling and the kettle shuts off — even if the sensor never quite reads 100 °C.
- Kettle detection: lifting the kettle stops heating immediately (the NTC reading goes out of its plausibility window).
- Safety layers
- over-temperature / dry-run shutdown at 110 °C (latched error with an alarm that ignores the mute switch, must be acknowledged manually),
- absolute heating timeout (5 min + keep-warm duration),
- a redundant 2 s watchdog that re-checks all of the above and forces the relay off in any non-heating state,
- relay is always off after boot, minimum 5 s between relay switches.
- Local UI: SSD1306 OLED (target, current temperature, status, countdown), four illuminated buttons (WS2812B), piezo beeps for confirmation / completion / errors, and a bouncing screensaver after 5 min of idling.
- Standalone-friendly networking: never reboots because Wi-Fi or the Home Assistant API are unreachable, fallback access point ("Wasserkocher Fallback") with captive portal, built-in web UI on port 80, OTA updates.
- Power tuning: 80 MHz CPU clock, Wi-Fi modem sleep, event-driven sensors that only publish real changes.
Controls
| Button | Action |
|---|---|
| On/Off | Start / stop heating; acknowledge a latched error |
| Program | Cycle through the presets 40 → 60 → 80 → 100 °C |
| Plus | Raise the target temperature by the configured step |
| Minus | Lower the target temperature by the configured step |
Home Assistant entities
Water temperature, target temperature, remaining time, heating rate,
status text and heater state, plus a stop button and configuration
entities for temperature step, keep-warm duration, button/display
brightness and sound on/off. Entity names and display texts are German —
both are defined centrally in the substitutions: block of
water_kettle.yml and easy to translate.
Repository layout
esphome_config/
water_kettle.yml ESPHome configuration (firmware)
pcb_design/
board.af Board design working file
kicad_project/ KiCad project: schematic, board, project librariesAll symbols, footprints and 3D models used by the schematic and board are
bundled under pcb_design/kicad_project/libraries/, so the KiCad project
(KiCad ≥ 9) opens without any external library setup. Generated files
(Gerber exports, backups, caches, autorouter files) are not tracked — see
.gitignore.
Hardware overview
- MCU: ESP32-S3-WROOM-1 (ESP-IDF framework)
- Power: TUHS3F05 AC/DC module (mains → 5 V), USB-C connector for flashing
- Heater switching: Omron G2RL-1A-E relay (5 V coil)
- Sensing: 100 kΩ NTC (B ≈ 3950, 150 kΩ pull-up) read via ADC, converted with the Steinhart–Hart equation
- UI: SSD1306 128×64 OLED (I²C, PCA9306 level translator), four tactile switches with one WS2812B-2020 RGB LED each, piezo buzzer
Pin map
| GPIO | Function | GPIO | Function |
|---|---|---|---|
| GPIO1 | On/Off LED (WS2812B) | GPIO8 | Program LED |
| GPIO2 | Plus LED | GPIO10 | On/Off button |
| GPIO3 | I²C SCL (OLED) | GPIO11 | Plus button |
| GPIO4 | I²C SDA (OLED) | GPIO12 | Minus button |
| GPIO5 | Piezo buzzer (PWM) | GPIO13 | Program button |
| GPIO6 | NTC temperature (ADC) | GPIO21 | Heater relay |
Building & flashing
-
Install ESPHome (≥ 2025.2, required for the
cpu_frequencyoption). -
Create
esphome_config/secrets.yaml(gitignored) with your credentials:yaml wifi_ssid: "..." wifi_password: "..." ap_password: "..." ota_password: "..." -
Compile and flash (first time via USB, afterwards OTA):
sh esphome run esphome_config/water_kettle.yml
⚠️ Safety warning
This project switches mains voltage (230 V) right next to water. Build and use it only if you are qualified to work with mains-powered appliances. The firmware's software protections do not replace proper hardware safety measures (fusing, creepage distances, the base's thermal protection). Everything here is provided as-is, without any warranty — use at your own risk.
Parts
67| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 0.1 uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4, C5, C6, C7, C11, C12, C14 |
| 6 | 10K | Resistor_SMD:R_1206_3216Metric | R2, R7, R9, R10, R12, R13 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H7, H8, H9, H10 |
| 4 | TS04-66-50-BK-100-SMT-TR | LIB_TS04-66-50-BK-100-SMT-TR:TS046650BK100SMTTR | S1, S2, S3, S4 |
| 4 | WS2812B-2020 | 4684:LED_WS2812B-2020_PLCC4_2.0x2.0mm_4684 | D6, D7, D8, D9 |
| 3 | 10 uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C10, C13 |
| 2 | 0R | Resistor_SMD:R_1206_3216Metric | R1, R14 |
| 2 | 1K | Resistor_SMD:R_1206_3216Metric | R6, R15 |
| 2 | 230V AC L | DMA_FOOTPRINTS:MountingHole_1.7mm_Pad | H3, H4 |
| 2 | 5.1K | Resistor_SMD:R_1206_3216Metric | R3, R4 |
| 2 | D_Schottky | Diode_SMD:D_SMA | D1, D2 |
| 2 | SW_Push | Button_Switch_SMD:SW_Tactile_SPST_NO_Straight_CK_PTS636Sx25SMTRLFS | SW1, SW2 |
| 1 | 0.1 uF 275VAC | Capacitor_THT:C_Rect_L13.0mm_W6.0mm_P10.00mm_FKS3_FKP3_MKS4 | C8 |
| 1 | 1 uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2 |
| 1 | 100K | Resistor_SMD:R_1206_3216Metric | R16 |
| 1 | 10D561K | Varistor:RV_Disc_D12mm_W5.8mm_P7.5mm | RV1 |
| 1 | 200K | Resistor_SMD:R_1206_3216Metric | R11 |
| 1 | 230V AC HEATER L | DMA_FOOTPRINTS:MountingHole_1.7mm_Pad | H5 |
| 1 | 230V AC HEATER N | DMA_FOOTPRINTS:MountingHole_1.7mm_Pad | H6 |
| 1 | 230VAC L | DMA_FOOTPRINTS:MountingHole_2x_1.4mm_5.08P_Pad | H1 |
| 1 | 230VAC N | DMA_FOOTPRINTS:MountingHole_2x_1.4mm_5.08P_Pad | H2 |
| 1 | 2A 250V T | Fuse:Fuse_2512_6332Metric | F1 |
| 1 | 3.3v 1A | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_1.0x1.0mm | TP1 |
| 1 | 400BXW18MEFR16X16 | Capacitor_THT:CP_Radial_D16.0mm_P7.50mm | C9 |
| 1 | CPT-9019S-SMT-TR | LIB_CPT-9019S-SMT-TR:CPT9019SSMTTR | LS1 |
| 1 | Do not populate | DMA_FOOTPRINTS:PinHeader_1x04_P2.54mm_Vertical_not_populated | J2 |
| 1 | ESP32-S3-WROOM-1 | PCM_Espressif:ESP32-S3-WROOM-1 | U1 |
| 1 | G2RL-1A-E-HA DC5 | LIB_G2RL-1A-E-HA_DC5:G2RL1AEASIDC12 | K1 |
| 1 | GND | TestPoint:TestPoint_Pad_1.0x1.0mm | TP4 |
| 1 | NRVA4007T3G | Diode_SMD:D_SMA | D5 |
| 1 | NTC Conn | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | PCA9306DCTT | LIB_PCA9306DCTT:SOP65P400X130-8N | IC1 |
| 1 | Q_NPN_BEC | Package_TO_SOT_SMD:SOT-23-3 | Q1 |
| 1 | RXD | TestPoint:TestPoint_Pad_1.0x1.0mm | TP3 |
| 1 | TUHS3F05 | LIB_TUHS3F05:TUHS3F05 | PS1 |
| 1 | TXD | TestPoint:TestPoint_Pad_1.0x1.0mm | TP2 |
| 1 | USB4940-00-A | LIB_USB4940-00-A:USB494000A | J1 |
Similar boards
- 8 layers163.5 × 123.5 mm

- 2 layers88.8 × 45.7 mm

PI Build
wbsipz/hardware-design-portfolio
Hardware design portfolio featuring power electronics, embedded control, and PCB projects.
33 parts - 2 layers48 × 65.5 mm

Open telegraph
animesh-chouhan/open-telegraph
A pocket-size Morse key. One button, one RGB LED, an ESP32-S3, and a battery. Plug it in over USB-C or pair it over Bluetooth and it types Morse into any device as a standard keyboard. Fully open, down to the copper.
52 parts5CERN-OHL-S-2.0 - 4 layers142 × 90 mm

- 2 layers94 × 82 mm

- 2 layers44 × 71 mm

- 2 layers100 × 100 mm

ENRTENADOR ATMEGA1284P
iSebass/MicrocontroladoresTeoria-Practicas
Este repositorio ha sido creado como un recurso de apoyo para el curso de Microcontroladores impartido en la Universidad del Valle. En este espacio colaboraremos con el Dr. en Ingeniería Sergio Arenas y el Ing.
149 parts1 - 2 layers98 × 70 mm

Questions
How big is the Wasserkocher PCB?
It measures 59.7 × 127.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Wasserkocher use?
67 parts, built around the ESP32-S3-WROOM-1-N8R2, TUHS3F05, AZ1117CH-3.3TRG1 and PCA9306DCTT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Wasserkocher KiCad files?
From the dmatscheko/water_kettle repository on GitHub, at the commit this page was made from: the board is pcb_design/kicad_project/wasserkocher.kicad_pcb and its schematic pcb_design/kicad_project/wasserkocher.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Wasserkocher design in my own project?
Its repository states no licence, so its author keeps all rights: ask dmatscheko before reusing the design.
