Skip to the content
1234567

TLV75533PDRV

Texas InstrumentsExtended

-40℃~+125℃@(Tj) 1 238mV@(500mA) 25uA 3.3V 46dB@(100kHz) 5.5V 500mA 71.5uVrms Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Input under-voltage protection、Output discharge、Built-in soft-start Positive WSON-6-EP(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
ti/TLV75533PDRV
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
WSON-6-EP(2x2)
Pins
6
In stock
17,441 at JLCPCB (C2861750)
Used on
26 open-source boards

Overview

The TLV75533PDRV is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Texas Instruments in a WSON-6-EP(2x2) package with 7 pins. -40℃~+125℃@(Tj) 1 238mV@(500mA) 25uA 3.3V 46dB@(100kHz) 5.5V 500mA 71.5uVrms Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Input under-voltage protection、Output discharge、Built-in soft-start Positive WSON-6-EP(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (Regulator_Linear:TLV75533PDRV, from KiCad's library) and its footprint (Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm, from KiCad's library), ready for a KiCad board. 17,441 are in stock at JLCPCB (part C2861750). 26 open-source boards in 23 repositories on GitHub use it.

Symbol

1OUT3GND4EN6IN
Regulator_Linear:TLV75533PDRVFrom KiCad's library

Footprint

1234567
Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mmFrom KiCad's library

From the datasheet

13
Supply, least
1.45 V · VIN, recommended operating min · p. 4
Supply, most
5.5 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
6 V · VIN, absolute max · p. 4
Junction, hottest
150 °C · Junction temperature, absolute max · p. 4
Takes working
25 µA · Ground current, typical at TJ = 25°C, IOUT = 0mA · p. 5
Takes asleep
100 nA · Shutdown current, typical with VEN ≤ 0.4V · p. 5
Gives
500 mA · Output current, recommended max · p. 4
Current limit
720 mA · Output current limit, typical at VOUT = 0.9 x nominal output · p. 5
Dropout
150 mV · Dropout, typical at 500mA, −40°C to +85°C · p. 6
Dropout
238 mV · Dropout, max at 500mA, −40°C to +125°C · p. 6
Junction to air (DRV)
100.2 K/W · Junction-to-ambient thermal resistance, JEDEC PCB · p. 5
Junction to case (DRV)
108.5 K/W · Junction-to-case top thermal resistance, JEDEC PCB · p. 5
Junction to board (DRV)
64.3 K/W · Junction-to-board thermal resistance, JEDEC PCB · p. 5

What it is and has

4
Soft-start
Built-in, with monotonic VOUT rise · p. 1
Current limit
Foldback · p. 1
Output discharge
Active · p. 1
Package
2mm × 2mm WSON-6 (DRV) · p. 1

Around it

2
cap 1µF or larger
between IN and GND; Required; effective capacitance at the pin must be greater than 0.47uF. · p. 3
cap 1µF or larger
between OUT and GND; Required; ceramic output capacitor supported; effective capacitance at the pin must be greater than 0.47uF. · p. 3

Specifications

45
ParameterConditionsAs printedPage
Supply voltage VINOver operating free-air temperature rangemin -0.3 · max 6 V4
Enable voltage VENOver operating free-air temperature rangemin -0.3 · max 6 V4
Output voltage VOUTMaximum is VIN + 0.3 V or 6.0 V, whichever is smallermin -0.3 V4
Operating junction temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±1000 Vmax 1000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±500 Vmax 500 V4
Input voltage VINmin 1.45 · max 5.5 V4
Output voltage VOUTmin 0.6 · max 5 V4
Enable voltage VENmin 0 · max 5.5 V4
Output current IOUTmin 0 · max 500 mA4
Input capacitor CINmin 1 uF4
Output capacitor COUTmin 1 · max 200 uF4
Enable toggle frequency fENmax 10 kHz4
Junction temperature TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJADRV (WSON), 6 PINS; JEDEC PCBtyp 100.2 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)DRV (WSON), 6 PINS; JEDEC PCBtyp 108.5 °C/W5
Junction-to-board thermal resistance RθJBDRV (WSON), 6 PINS; JEDEC PCBtyp 64.3 °C/W5
Junction-to-top characterization parameter ψJTDRV (WSON), 6 PINS; JEDEC PCBtyp 10.4 °C/W5
Junction-to-board characterization parameter ψJBDRV (WSON), 6 PINS; JEDEC PCBtyp 64.8 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)DRV (WSON), 6 PINS; JEDEC PCBtyp 34.7 °C/W5
Output accuracy−40°C ≤ TJ ≤ +85°C, DRV packagemin -1 · max 1 %5
Output accuracyVOUT ≥ 1V; −40°C ≤ TJ ≤ +125°Cmin -1.5 · max 1.5 %5
Line regulation (ΔVOUT)ΔVINVOUT + 0.5V ≤ VIN ≤ 5.5V, VOUT > 1.5Vtyp 2 mV5
Load regulation ΔVOUT/ΔIOUTDRV package; 0.1mA ≤ IOUT ≤ 500mAtyp 0.044 V/A5
Ground current IGNDTJ = 25°C, IOUT = 0mAmin 14 · typ 25 · max 31 uA5
Ground current IGND−40°C ≤ TJ ≤ +85°C, IOUT = 0mAmax 33 uA5
Ground current IGND−40°C ≤ TJ ≤ +125°C, IOUT = 0mAmax 40 uA5
Shutdown current ISHDNVEN ≤ 0.4V, 1.4V ≤ VIN ≤ 5.5V, −40°C ≤ TJ ≤ +125°Ctyp 0.1 · max 1 uA5
Output current limit ICLVIN = VOUT + VDO(MAX) + 0.25V; VOUT = 0.9 x VOUT, 1.5V < VOUT ≤ 4.5Vmin 560 · typ 720 · max 865 mA5
Short-circuit current limit ISCVOUT = 0Vtyp 355 mA5
Dropout voltage VDODRV package; 3.3V ≤ VOUT < 5.0V; IOUT = 500mA, −40°C ≤ TJ ≤ +85°Ctyp 150 · max 215 mV6
Dropout voltage VDODRV package; 3.3V ≤ VOUT < 5.0V; IOUT = 500mA, −40°C ≤ TJ ≤ +125°Cmax 238 mV6
Power-supply rejection ratio PSRRf = 1kHz, VIN = VOUT + 1V, IOUT = 50mAtyp 52 dB6
Power-supply rejection ratio PSRRf = 100kHz, VIN = VOUT + 1V, IOUT = 50mAtyp 46 dB6
Power-supply rejection ratio PSRRf = 1MHz, VIN = VOUT + 1 V, IOUT = 50mAtyp 52 dB6
Undervoltage lockout VUVLOVIN risingmin 1.21 · typ 1.3 · max 1.44 V6
Undervoltage lockout hysteresis VUVLO,HYSTVIN fallingtyp 40 mV6
Startup time tSTRtyp 550 us6
EN pin high voltage (enabled) VHImin 1 V6
EN pin low voltage (enabled) VLOmax 0.3 V6
Enable pin current IENEN = 5.5Vtyp 10 nA6
Thermal shutdown TSDShutdown, temperature increasingtyp 165 °C6
Thermal shutdown TSDReset, temperature decreasingtyp 155 °C6
Pulldown resistance RPULLDOWNVIN = 5.5Vtyp 120 Ω6

Pins, by the datasheet

7
1 OUT
Regulated output voltage; connect a capacitor of 1uF or larger to ground. · p. 3
2 NC
No internal connection. · p. 3
3 GND
Ground pin. · p. 3
4 EN
Drive above VHI to enable the regulator; drive below VLO for shutdown. · p. 3
5 NC
No internal connection. · p. 3
6 IN
Input supply; connect a capacitor of 1uF or larger to ground. · p. 3
Pad Thermal pad
Internally connected to GND; connect to a large-area ground plane. · p. 3

Open-source boards using it

26See all 26
  • 4 layers65 × 49.8 mm2.5in IDE SSD no lengthmatch, the printed circuit board in 3D

    2.5in IDE SSD no lengthmatch

    dosdude1/2.5-inch-ide-ssd

    A custom-designed IDE SSD for use in any machine that utilizies a 2.5" IDE hard disk.

    91 parts334GPL-3.0
  • 2 layers41.6 × 47.3 mmHomekey, the printed circuit board in 3D

    Homekey

    lollokara/HomeKey-ESP32-PCB

    HomeKey-ESP32-PCB A miniaturized, wall-mountable HomeKey reader board

    71 parts20
  • 6 layers26 × 25 mmTektag, the printed circuit board in 3D

    Tektag

    teklabsdigital/TekTag

    Biosensor for telehealth, patient monitoring, fall detection, dementia geofencing and cardiograms

    93 parts18
  • 4 layers52.5 × 59.7 mmESPHome Indoor Multi Sensor, the printed circuit board in 3D

    ESPHome Indoor Multi Sensor

    mikelawrence/esphome-indoor-multi-sensor-hardware

    ESPHome Indoor Multi-Sensor hardware. This design supports Radar/PIR Presence, Temperature, Humidity, Pressure, Light, CO2, CO, VOC, NOX and PM sensors.

    113 parts14CERN-OHL-P-2.0
  • 2 layers31 × 17 mmUsbCarrierMM8108, the printed circuit board in 3D

    UsbCarrierMM8108

    JeffersonSchostakovich/halowBoards

    MM8108-based adapters in different form factors for EU availability of sub-GHz halow 802.11ah hardware - mainly for decentralised networking (Reticulum mesh) and distributed IoT experimentation purposes.

    23 parts8
  • 2 layers46 × 15.2 mmTots, the printed circuit board in 3D

    Tots

    mimok/yast-hw

    Hardware source files of the YAST security token from OTS Security

    29 parts6CC-BY-4.0
  • 4 layers35.6 × 17.8 mmIcebreaker bitsy, the printed circuit board in 3D

    Icebreaker bitsy

    murkyshelf/fpga_dev_board

    99 parts2Apache-2.0
  • 4 layers26.4 × 50.8 mmIOT, the printed circuit board in 3D

    IOT

    yuanyong2024/IoT-feather

    a IoT evb board that based on Quectel BG95 modem and in adafruit feather form factor

    111 parts2

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TLV75533PDRV?

Yes. The symbol is Regulator_Linear:TLV75533PDRV and the footprint Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TLV75533PDRV?

WSON-6-EP(2x2), with 7 pins. Its footprint is drawn on this page.

Where is the TLV75533PDRV datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TLV75533PDRV?

JLCPCB lists it as part C2861750, with 17,441 in stock; the sellers' links on this page open their listings.

What can replace the TLV75533PDRV?

Parts like it in the library: the TLV76733DRVR by Texas Instruments, the LP5912-3.3DRVR by Texas Instruments, the TLV75733PDRV by Texas Instruments and the LP5912-3.3DRVT by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TLV75533PDRV?

26 boards in 23 repositories on GitHub; the most starred are listed on this page, with their KiCad files.