Skip to the content
1234567

TLV76733DRVR

Texas InstrumentsExtended

-40℃~+125℃@(Tj) 1 1.4V@(1A) 16V 1A 3.3V 46dB@(1MHz) 50uA 60uVrms Fixed Over Current Protection、Over Temperature Protection、Soft Start Positive WSON-6(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
ti/TLV76733DRVR
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
WSON-6(2x2)
Pins
7
In stock
35,854 at JLCPCB (C2848334)
Used on
33 open-source boards

Overview

The TLV76733DRVR is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Texas Instruments in a WSON-6(2x2) package with 7 pins. -40℃~+125℃@(Tj) 1 1.4V@(1A) 16V 1A 3.3V 46dB@(1MHz) 50uA 60uVrms Fixed Over Current Protection、Over Temperature Protection、Soft Start Positive WSON-6(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (Regulator_Linear:TLV76733DRVx, from KiCad's library) and its footprint (Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm, from KiCad's library), ready for a KiCad board. 35,854 are in stock at JLCPCB (part C2848334). 33 open-source boards in 27 repositories on GitHub use it.

Symbol

1OUT2SNS3GND4EN6IN7PAD
Regulator_Linear:TLV76733DRVxFrom KiCad's library

Footprint

1234567
Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mmFrom KiCad's library

From the datasheet

17
Supply, least
2.5 V · VIN, recommended operating min · p. 5
Supply, most
16 V · VIN, recommended operating max · p. 5
Supply, absolute maximum
18 V · VIN, absolute max · p. 5
Works from
-40 °C · Operating temperature min · p. 1
Works up to
125 °C · Operating temperature max · p. 1
Junction, hottest
150 °C · Operating junction temperature absolute max · p. 5
Takes working
60 µA · IQ typical, fixed output, IOUT = 0 mA · p. 6
Takes asleep
1.5 µA · Shutdown current typical, VEN ≤ 0.4 V, VIN = 16 V · p. 6
Gives
800 mA · Output current max, 2.5 V ≤ VIN < 3 V · p. 5
Gives
1 A · Output current max, VIN ≥ 3 V · p. 5
Current limit
1.1 A · Output current limit min, VOUT = 0.9 × nominal, VIN ≥ 3 V · p. 6
Current limit
810 mA · Output current limit min, VOUT = 0.9 × nominal, 2.5 V ≤ VIN < 3 V · p. 6
Dropout
900 mV · Dropout typical, IOUT = 1 A, VIN ≥ 3 V, DRV · p. 6
Dropout
800 mV · Dropout typical, IOUT = 800 mA, 2.5 V ≤ VIN < 3 V · p. 6
Junction to air (DRV (WSON))
77.7 K/W · Junction-to-ambient thermal resistance · p. 6
Junction to board (DRV (WSON))
40.8 K/W · Junction-to-board thermal resistance · p. 6
Junction to case (DRV (WSON))
92.3 K/W · Junction-to-case top thermal resistance · p. 6

What it is and has

4
Protection
Foldback current limit and thermal protection · p. 1
Soft start
500µs typical · p. 1
Output accuracy
1% over load and temperature · p. 1
Package
6-pin 2mm × 2mm WSON · p. 1

Around it

2
cap 1 µF
between IN and GND; Nominal input capacitance; place as close to IN and GND as possible. · p. 5
cap 2.2 µF
between OUT and GND; Nominal output capacitance; table range 1–220 uF. Place as close to OUT and GND as possible. · p. 5

Specifications

43
ParameterConditionsAs printedPage
Voltage VINWith respect to GNDmin -0.3 · max 18 V5
Voltage VSNSMaximum VIN + 0.3 V or 18 V, whichever is smallermin -0.3 V5
Voltage VENWith respect to GNDmin -0.3 · max 18 V5
Operating junction (TJ) TJmin -50 · max 150 °C5
Storage (TSTG) TSTGmin -65 · max 150 °C5
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pinsmin -3000 · max 3000 V5
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pinsmin -1000 · max 1000 V5
Input voltage VINmin 2.5 · max 16 V5
Enable voltage VENmin 0 · max 16 V5
Output voltage VOUTFamily output rangemin 0.8 · max 14.6 V5
Output current IOUT2.5 V ≤ VIN < 3 Vmin 0 · max 0.8 A5
Output current IOUTVIN ≥ 3 Vmin 0 · max 1 A5
Output capacitor(1) COUTNominal value in typ fieldmin 1 · typ 2.2 · max 220 uF5
Output capacitor ESR COUT ESRmin 2 · max 500 mΩ5
Input capacitor CINNominal value in typ fieldtyp 1 uF5
Junction temperature TJmin -40 · max 125 °C5
Junction-to-ambient thermal resistance RθJADRV (WSON), 6 PINStyp 77.7 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)DRV (WSON), 6 PINStyp 92.3 °C/W6
Junction-to-board thermal resistance RθJBDRV (WSON), 6 PINStyp 40.8 °C/W6
Junction-to-top characterization parameter ΨJTDRV (WSON), 6 PINStyp 4.3 °C/W6
Junction-to-board characterization parameter ΨJBDRV (WSON), 6 PINStyp 40.8 °C/W6
Junction-to-case (bottom) thermal resistance RθJC(bot)DRV (WSON), 6 PINStyp 18.9 °C/W6
Nominal output accuracy VOUTTJ = 25°Cmin -0.5 · max 0.5 %6
Output accuracy over temperature VOUTVIN ≥ 3.0 V, 1 mA ≤ IOUT ≤ 1 Amin -1 · max 1 %6
Output accuracy over temperature VOUT2.5 V ≤ VIN < 3.0 V, 1 mA ≤ IOUT ≤ 800 mAmin -1 · max 1 %6
Line regulation(1) ΔVOUT(ΔVIN)VOUT(NOM) +1.5 V ≤ VIN ≤ 16 V, IOUT = 10 mAmax 0.02 %/V6
Load regulation ΔVOUT(ΔIOUT)1 mA ≤ IOUT ≤ 1 A, VIN ≥ 3.0 Vtyp 0.1 · max 0.5 %/A6
Load regulation ΔVOUT(ΔIOUT)1 mA ≤ IOUT ≤ 800 mA, 2.5 V ≤ VIN < 3.0 Vtyp 0.1 · max 0.5 %/A6
Dropout voltage(2) VDOVIN ≥ 3.0V, IOUT = 1 A, DRV packagetyp 0.9 · max 1.4 V6
Dropout voltage(2) VDO2.5 V ≤ VIN < 3.0 V, IOUT = 800 mAtyp 0.8 · max 1.3 V6
Output current limit ICLVOUT = 0.9 x VOUT(NOM), VIN ≥ 3.0Vmin 1.1 · max 1.6 A6
Output current limit ICLVOUT = 0.9 x VOUT(NOM), 2.5 V ≤ VIN < 3.0 Vmin 0.81 · max 1.6 A6
Short-circuit current limit ISCVOUT = 0 V, DRV packagemin 150 · typ 250 · max 350 mA6
Quiescent current IQFixed output devices, IOUT = 0 mAtyp 60 · max 95 uA6
Ground current IGNDIOUT = 1 A, VIN ≥ 3.0 Vtyp 1.5 mA6
Shutdown current ISHUTDOWNVEN ≤ 0.4 V, VIN = 16 Vtyp 1.5 · max 3 uA6
Enable pin logic high VEN(HIGH)2.5 V ≤ VIN ≤ 16 Vmin 1.2 V6
Enable pin logic low VEN(LOW)2.5 V ≤ VIN ≤ 16 Vmax 0.4 V6
Enable pullup current IENVEN = 0 Vtyp 400 nA6
Output pulldown current IPULLDOWNVIN = 16 V, VOUT = 2.5 V, VEN=0Vtyp 1.2 mA6
Power-supply rejection ratio PSRRVIN = 3.3 V, VOUT = 1.8 V, IOUT = 300 mA, f = 120 Hztyp 70 dB6
Output noise voltage VnBW = 10 Hz to 100 kHz, VIN = 3.3 V, VOUT = 0.8 V, IOUT = 100 mAtyp 60 uVRMS6
UVLO threshold rising VUVLO+VIN risingtyp 2.2 · max 2.4 V6

Pins, by the datasheet

7
1 OUT
Output; place the recommended output capacitor as close to OUT and GND as possible. · p. 4
2 SNS
Output sense; connect to OUT or to the load for remote sensing. Do not float. · p. 4
3 GND
Ground; must be grounded. · p. 4
4 EN
High enables and low disables the device. Internal pullup permits leaving it floating; it may also connect to IN. · p. 4
5 GND
Ground; must be grounded. · p. 4
6 IN
Input; place the recommended input capacitor as close to IN and GND as possible. · p. 4
Pad Thermal pad
Connect to ground or leave floating; connect to a large-area ground plane for best thermal performance. · p. 3

Open-source boards using it

33See all 33
  • 6 layers31.2 × 33 mm4in1-mini, the printed circuit board in 3D

    4in1-mini

    OpenDrone-hw/OpenESC-20x20

    Open-source 4-in-1 AM32 ESC for FPV drones. 20x20 mm, 2-6S, one MCU per motor, CERN-OHL-S-2.0.

    191 parts279CERN-OHL-S-2.0
  • 4 layers55 × 55 mmCaw bms, the printed circuit board in 3D

    Caw bms

    noxrick91/caw-bms

    锂电池管理系统

    154 parts228GPL-3.0
  • 4 layers50 × 42 mmCawDrive, the printed circuit board in 3D

    CawDrive

    noxrick91/caw-drive

    三相直流无刷电机驱动器硬件

    112 parts108GPL-3.0
  • 6 layers41.6 × 80.4 mm4in1-panel, the printed circuit board in 3D

    4in1-panel

    OpenDrone-hw/OpenESC-30x30

    Open-source 4-in-1 AM32 ESC for FPV drones. 30.5x30.5 mm, 2-8S, one MCU per motor, CERN-OHL-S-2.0.

    404 parts85CERN-OHL-S-2.0
  • 2 layers40.6 × 108 mmUseq1, the printed circuit board in 3D

    Useq1

    Emute-Lab-Instruments/uSEQ

    Hardware & firmware of the uSEQ Live Coding CV & Gate Sequencer

    172 parts44
  • 6 layers40.5 × 43 mmVENDETTAESC, the printed circuit board in 3D

    VENDETTAESC

    Caped-Crussader/VENDETTAFC

    A fully open-source, custom-designed 4-in-1 ESC and F7 Flight Controller stack for FPV multirotors, designed from scratch in KiCad.

    236 parts31CERN-OHL-S-2.0
  • 8 layers35 × 35 mmOpenAIO, the printed circuit board in 3D

    OpenAIO

    OpenDrone-hw/OpenAIO

    Open-source AIO for 2-6S toothpick quads: flight controller, 4-in-1 AM32 ESC and ExpressLRS receiver, 25.5x25.5 mm.

    343 parts19CERN-OHL-S-2.0
  • 4 layers155 × 103 mmMEMLNaut 0 3, the printed circuit board in 3D

    MEMLNaut 0 3

    MusicallyEmbodiedML/MEMLNaut

    138 parts6

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TLV76733DRVR?

Yes. The symbol is Regulator_Linear:TLV76733DRVx and the footprint Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TLV76733DRVR?

WSON-6(2x2), with 7 pins. Its footprint is drawn on this page.

Where is the TLV76733DRVR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TLV76733DRVR?

JLCPCB lists it as part C2848334, with 35,854 in stock; the sellers' links on this page open their listings.

What can replace the TLV76733DRVR?

Parts like it in the library: the TLV75733PDRV by Texas Instruments, the TLV76733DRVT by Texas Instruments, the AMS1117-3.3 by Advanced Monolithic Systems and the AMS1117-3.3 by UMW. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TLV76733DRVR?

33 boards in 27 repositories on GitHub; the most starred are listed on this page, with their KiCad files.