

CawDrive
三相直流无刷电机驱动器硬件
- Size
- 50 × 42 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 112
- Nets
- 143
- Pads
- 430
- Tracks, vias
- 964, 297
- Pours
- 268
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 4 Oct 2023
- Updated
- 5 Feb 2026
Overview
CawDrive is an open-source printed circuit board by noxrick91, from the noxrick91/caw-drive repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 50 × 42 mm with 112 parts on 143 nets, routed with 964 tracks and 297 vias.
It is built around the TJA1051T/3/1J, MT6835GT-STD-R and WAFER-SH1.0-2PWB, with the TLV76733DRVR, TPH3R704PL,L1Q and 0.1UF 50V 5*11 among its other parts. Its parts include 37 capacitors, 26 resistors, 10 ICs, 7 transistors and 5 diodes. It belongs with the STM32 boards of this library.
Main components
9TJA1051T/3/1J
SOIC-8-150mil-40℃~+150℃ 110mA 4.5V~5.5V 5Mbps CAN FD Transceiver SOIC-8-150mil CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversMT6835GT-STD-R
TSSOP-16-40℃~+125℃ 0°~360° 1.2mm 22mA 3V~5.5V 4.4mm 5mm Magnetic rotary position sensor No SPI Zero position programming、Fault diagnosis、Angle nonlinearity compensation、Self-calibration TSSOP-16 Position Sensors ROHSNOVOSENSEPosition SensorsWAFER-SH1.0-2PWB
SMD,P=1mm,卧贴-40℃~+85℃ 1 1A 1mm 1x2P 2 2P 3.15mm 4.35mm 4.3mm 50V Auxiliary Solder Pin Beige Brass LCP SH Surface Mount, Right Angle Tin SMD,P=1mm,卧贴 Wire To Board Connector ROHSXUNPUWire To Board ConnectorTLV76733DRVR
WSON-6(2x2)-40℃~+125℃@(Tj) 1 1.4V@(1A) 16V 1A 3.3V 46dB@(1MHz) 50uA 60uVrms Fixed Over Current Protection、Over Temperature Protection、Soft Start Positive WSON-6(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTPH3R704PL,L1Q
DSOP-8-EP-5.0mm1 N-channel 2.4V 2.5nF 27nC@10V 40V 6mΩ@4.5V 80pF 81W 92A DSOP-8-EP-5.0mm MOSFETs ROHSToshibaMOSFETs0.1UF 50V 5*11
插件,5x11mm1000hrs@105℃ 100nF 11mm 1A@100kHz 2mm 50V 5mm 插件,5x11mm Aluminum Electrolytic Capacitors - Leaded ROHSCXAluminum Electrolytic Capacitors - LeadedCSTNE16M0V530000R0
SMD3213-3P-40℃~+85℃ 15pF 16MHz 40Ω SMD3213-3P Ceramic Resonators ROHSMurataCeramic ResonatorsWAFER-SH1.0-4PWB
SMD,P=1mm,卧贴-40℃~+85℃ 1 1A 1mm 1x4P 3.15mm 4 4.3mm 4P 50V 6.35mm Auxiliary Solder Pin Beige Brass LCP SH Surface Mount, Right Angle Tin SMD,P=1mm,卧贴 Wire To Board Connector ROHSXUNPUWire To Board ConnectorWAFER-SH1.0-6PWB
SMD,P=1mm,卧贴-40℃~+85℃ 1 1A 1mm 1x6P 3.15mm 4.3mm 50V 6 6P 8.35mm Auxiliary Solder Pin Beige Brass LCP SH Surface Mount, Right Angle Tin SMD,P=1mm,卧贴 Wire To Board Connector ROHSXUNPUWire To Board Connector
README
README.mdParts
112| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 0.1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C2, C3, C4, C5, C6, C11, C12, C13, C14, C17, C18 |
| 11 | 10uF/50V | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C20, C21, C22, C23, C24, C25, C26, C29, C36, C37, C38 |
| 9 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9 |
| 8 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R3, R5, R6, R10, R16, R17, R22 |
| 6 | TPH3R704PL | Rick_MOSFET:TPHR8504PL,L1Q | Q7, Q8, Q9, Q10, Q11, Q12 |
| 5 | MountingHole_Pad | CawDrive_Connector:POWER_PAD | H5, H6, H7, H8, H9 |
| 5 | WAFER-SH1.0-2PWB | Rick_Connector:CONN-SMD_2P-P1.00_XUNPU_WAFER-SH1.0-2PWB | U5, U6, U10, U11, U12 |
| 4 | 510Ω | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7, R9, R11, R15 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.5mm_Pad_Via | H1, H2, H3, H4 |
| 3 | 1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C7, C31, C32 |
| 3 | 22uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C16, C34, C35 |
| 2 | 0.1uF/50V | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C15, C33 |
| 2 | 0.1uF/50V | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C10, C19 |
| 2 | 0Ω | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4, R24 |
| 2 | 10K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R23, R25 |
| 2 | 10k 0.1% | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R20 |
| 2 | 5mΩ 1% | Resistor_SMD:R_1210_3225Metric_Pad1.30x2.65mm_HandSolder | R18, R19 |
| 1 | 0.1uF/50V | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C30 |
| 1 | 10k NTC | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R21 |
| 1 | 10k ±0.1% | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R14 |
| 1 | 120Ω 1% | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R26 |
| 1 | 1uF/50V | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C28 |
| 1 | 2.2uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C9 |
| 1 | 22uH_±20%_1.4A | Rick_Inductor:LQH5BPB220MT0L_IND-SMD_L5.0-W5.0 | L2 |
| 1 | 39nH | Inductor_SMD:L_0402_1005Metric_Pad0.77x0.64mm_HandSolder | L1 |
| 1 | 3k 0.1% | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R12 |
| 1 | 47nF/50V | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C27 |
| 1 | 54.9k ±0.1% | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R13 |
| 1 | 75k 0.1% | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R8 |
| 1 | CSTNE16M0V530000R0 | Rick_Crystal:Crystal_SMD3213-3P | X1 |
| 1 | DRV8323RSRGZR | Rick_Drive:DRV8323RS_QFN-48-EP(7x7) | U7 |
| 1 | DRV_STA_LED | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D2 |
| 1 | D_Schottky_Small | Diode_SMD:D_SOD-123 | D3 |
| 1 | ENCODER_STA_LED | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D6 |
| 1 | G*** | Library:kibuzzard-692C9AA1 | kibuzzard-692C9AA1 |
| 1 | G*** | Library:kibuzzard-692C9A5B | kibuzzard-692C9A5B |
| 1 | LOGO | Library:guaik_logo_black_7x7 | G*** |
| 1 | MCU_STA_LED | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D1 |
| 1 | MT6835GT-STD | Rick_Sensor:MT6835GT-STD | U9 |
| 1 | NMOS | Package_TO_SOT_SMD:SOT-723 | Q1 |
| 1 | PWR_STA_LED | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D4 |
| 1 | SMAJ36CA/TR13 | Rick_Diode:SMAJ36CA_TR13_SMA(DO-214AC) | TV1 |
| 1 | STM32F446RETx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U8 |
| 1 | TJA1051T/3/1J | Rick_CAN:TJA1051T31J_SOIC-8_L4.9-W3.9-P1.27-LS6.0-BL | U1 |
| 1 | TLV76733DRVR | Rick_Regulator_Linear:TLV76733DRVR_SON65P200X200X80-7N | U2 |
| 1 | WAFER-SH1.0-4PWB | Rick_Connector:CONN-SMD_4P-P1.00_WAFER-SH1.0-4PWB | CN3 |
| 1 | WAFER-SH1.0-6PWB | Rick_Connector:CONN-SMD_6P-P1.00_XUNPU_WAFER-SH1.0-6PWB | CN2 |
More from noxrick91/caw-drive
1- 2 layers21.5 × 19 mm

Similar boards
- 4 layers55 × 55 mm

- 4 layers44 × 43 mm

Pico mini
Ncerzzk/luckyfox_pico_mini_FC
A flight controller hardware based on LucyFox Pico Mini Board
50 partsGPL-3.0 - 2 layers74 × 27.5 mm

V485 feeder
gabrielyoung92/gabs_microSMT_PickAndPlace
Independent reorganisation of MicroSMT feeder and PNPv3 files, previews and documentation, with upstream attribution and ChatGPT assistance.
70 parts1 - 2 layers170.1 × 96.9 mm

SmartPrintCoreH7x
BoltzRnD/SmartPrintCoreH7x
STM32H7 based Robust and Open Source 3D Printer Mainboard
567 parts89 - 4 layers53.5 × 38 mm

- 4 layers46 × 47 mm

STMF051 Electric Speed controller
MatthiasGeorgImhof/STMF051_Electric_Speed_controller
An ESC (electronic speed controller) and serveo breakout board using 8 PWM inputs lines (1&2 ESC, 3-8 servos 1-6)
164 parts - 2 layers110 × 60 mm

LargeMD
Tomoshibi-technology/RCJ-Japan2024-Circuit
RoboCup JapanOpen 2024とEindohoven 2024に向けての回路開発
149 parts1MIT - 4 layers76 × 108 mm

Questions
How big is the CawDrive PCB?
It measures 50 × 42 mm and has 4 copper layers, 1.6 mm thick.
What parts does the CawDrive use?
112 parts, built around the TJA1051T/3/1J, MT6835GT-STD-R, WAFER-SH1.0-2PWB and TLV76733DRVR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the CawDrive KiCad files?
From the noxrick91/caw-drive repository on GitHub, at the commit this page was made from: the board is PCB/CawDrive.kicad_pcb and its schematic PCB/CawDrive.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the CawDrive design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).