Skip to the content
1234567

TLV75733PDRV

Texas InstrumentsExtended

-40℃~+125℃@(Tj) 1 1A 25uA 3.3V 425mV@(1A) 45dB@(100kHz) 5.5V 71.5uVrms Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Input under-voltage protection、Output discharge、Built-in soft-start Positive WSON-6(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
ti/TLV75733PDRV
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
WSON-6(2x2)
Pins
7
In stock
3,096 at JLCPCB (C2868428)
Used on
19 open-source boards

Overview

The TLV75733PDRV is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Texas Instruments in a WSON-6(2x2) package with 7 pins. -40℃~+125℃@(Tj) 1 1A 25uA 3.3V 425mV@(1A) 45dB@(100kHz) 5.5V 71.5uVrms Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Input under-voltage protection、Output discharge、Built-in soft-start Positive WSON-6(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (Regulator_Linear:TLV75733PDRV, from KiCad's library) and its footprint (Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm, from KiCad's library), ready for a KiCad board. 3,096 are in stock at JLCPCB (part C2868428). 19 open-source boards in 17 repositories on GitHub use it.

Symbol

1OUT3GND4EN6IN
Regulator_Linear:TLV75733PDRVFrom KiCad's library

Footprint

1234567
Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mmFrom KiCad's library

From the datasheet

12
Supply, least
1.45 V · VIN, recommended operating minimum · p. 4
Supply, most
5.5 V · VIN, recommended operating maximum · p. 4
Supply, absolute maximum
6 V · VIN, absolute maximum · p. 4
Junction, hottest
150 °C · Junction temperature, absolute maximum · p. 4
Takes working
25 µA · Ground current, typical at TJ = 25°C · p. 5
Takes asleep
100 nA · Shutdown current, typical, VEN ≤ 0.4V · p. 5
Gives
1 A · Output current, recommended maximum · p. 4
Current limit
1.55 A · Output current limit, typical, VIN = VOUT + VDO(MAX) + 0.25V · p. 5
Dropout
300 mV · Typical at IOUT = 1A, 3.3V output, –40°C ≤ TJ ≤ +85°C · p. 6
Junction to air (DRV (SON))
100.2 K/W · JEDEC junction-to-ambient thermal resistance · p. 5
Junction to board (DRV (SON))
64.3 K/W · JEDEC junction-to-board thermal resistance · p. 5
Junction to case (DRV (SON))
108.5 K/W · JEDEC junction-to-case top thermal resistance · p. 5

What it is and has

7
Soft start
Internal soft start with monotonic VOUT rise · p. 1
Protection
Foldback current limit · p. 1
Output discharge
Active output discharge · p. 1
Package
2mm × 2mm WSON-6 (DRV) · p. 1
Protection
Foldback current limit, shutdown, thermal protection · p. 13
Enable
Active high; connect EN to IN if shutdown is not required · p. 13
Output discharge
Internal 120Ω pulldown when disabled · p. 13

Around it

4
cap 1µF or larger
between IN and GND; Required; effective capacitance at the pin must exceed 0.47uF. · p. 3
cap 1µF or larger
between OUT and GND; Required; effective capacitance at the pin must exceed 0.47uF. · p. 3
cap 0.47μF or larger
between OUT and GND; Required for stability; use X5R or X7R ceramic. Place close to the device. · p. 16
cap 1µF or greater
between IN and GND; Input capacitor; place close to the device. Higher capacitance may be needed for fast load transients or a distant input source. · p. 16

Specifications

45
ParameterConditionsAs printedPage
Supply voltage VINOver operating free-air temperature rangemin -0.3 · max 6 V4
Enable voltage VENOver operating free-air temperature rangemin -0.3 · max 6 V4
Output voltage VOUTMaximum is VIN + 0.3V or 6.0V, whichever is smallermin -0.3 V4
Operating junction temperature range TJmin -40 · max 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±1000 Vmax 1000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±500 Vmax 500 V4
Input voltage VINmin 1.45 · max 5.5 V4
Output voltage VOUTmin 0.6 · max 5 V4
Enable voltage VENmin 0 · max 5.5 V4
Output current IOUTmin 0 · max 1 A4
Input capacitor CINmin 1 uF4
Output capacitor COUTmin 1 · max 200 uF4
Enable toggle frequency fENmax 10 kHz4
Junction temperature TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJADRV (SON), 6 PINS; JEDECtyp 100.2 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)DRV (SON), 6 PINS; JEDECtyp 108.5 °C/W5
Junction-to-board thermal resistance RθJBDRV (SON), 6 PINS; JEDECtyp 64.3 °C/W5
Junction-to-top characterization parameter ψJTDRV (SON), 6 PINS; JEDECtyp 10.4 °C/W5
Junction-to-board characterization parameter ψJBDRV (SON), 6 PINS; JEDECtyp 64.8 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)DRV (SON), 6 PINS; JEDECtyp 34.7 °C/W5
Output accuracy–40°C ≤ TJ ≤ 85°C, VOUT ≥ 1Vmin -1 · max 1 %5
Output accuracyVOUT ≥ 1V; –40°C ≤ TJ ≤ +125°Cmin -1.5 · max 1.5 %5
Line regulation (ΔVOUT)ΔVINVOUT + 0.5V ≤ VIN ≤ 5.5Vtyp 2 mV5
Load regulation ΔVOUT/ΔIOUTDRV package; 0.1mA ≤ IOUT ≤ 1A, VIN ≥ 2.4Vtyp 0.044 V/A5
Ground current IGNDTJ = 25°Ctyp 25 · max 31 uA5
Ground current IGND–40°C ≤ TJ ≤ +85°Cmax 33 uA5
Ground current IGND–40°C ≤ TJ ≤ +125°Cmax 40 uA5
Shutdown current ISHDNVEN ≤ 0.4V, 1.45V ≤ VIN ≤ 5.5Vtyp 0.1 · max 1 uA5
Output current limit ICLVIN = VOUT + VDO(MAX) + 0.25V; VOUT = 0.9 x VOUT, 1.5V < VOUT ≤ 4.5Vmin 1.2 · typ 1.55 · max 1.78 A5
Short circuit current limit ISCVOUT = 0V, VIN = VOUT + VDO(MAX) + 0.25Vtyp 755 mA5
Dropout voltage VDODRV package; IOUT = 1A, –40°C ≤ TJ ≤ +85°C; 3.3V ≤ VOUT < 5.0Vtyp 300 · max 425 mV6
Dropout voltage VDODRV package; IOUT = 1A, –40°C ≤ TJ ≤ +125°C; 3.3V ≤ VOUT < 5.0Vmax 475 mV6
Power supply rejection ratio PSRRf = 1kHz, VIN = VOUT + 1V, IOUT = 50mAtyp 52 dB6
Power supply rejection ratio PSRRf = 100kHz, VIN = VOUT + 1 V, IOUT = 50mAtyp 46 dB6
Power supply rejection ratio PSRRf = 1MHz, VIN = VOUT + 1V, IOUT = 50mAtyp 52 dB6
Undervoltage lockout VUVLOVIN risingmin 1.21 · typ 1.3 · max 1.44 V6
Undervoltage lockout hysteresis VUVLO, HYSTVIN fallingtyp 40 mV6
Startup time tSTRtyp 550 us6
EN pin high voltage (enabled) VHImin 1 V6
EN pin low voltage (enabled) VLOmax 0.3 V6
Enable pin current IENVIN = 5.5V, EN = 5.5Vtyp 10 nA6
Pulldown resistance RPULLDOWNVIN = 3.3V (P version only)typ 95 Ω6
Thermal shutdown TSDShutdown, temperature increasingtyp 165 °C7
Thermal shutdown TSDReset, temperature decreasingtyp 155 °C7

Pins, by the datasheet

7
1 OUT
Regulated output voltage; requires a capacitor of 1uF or larger to ground. · p. 3
2 NC
No internal connection. · p. 3
3 GND
Ground pin. · p. 3
4 EN
Drive above VHI to enable the regulator and below VLO for shutdown. · p. 3
5 NC
No internal connection. · p. 3
6 IN
Input supply; requires a capacitor of 1uF or larger to ground. · p. 3
Pad Thermal pad
Internally connected to GND; connect to a large-area ground plane. · p. 3

Ordering codes, by the datasheet

2
TLV75733PDRVRG4
WSON (DRV) | 6 · 3000 pieces, LARGE T&R; operating temperature -40 to 125°C; marking 1HPH · p. 27
TLV75733PDRVRG4.A
WSON (DRV) | 6 · 3000 pieces, LARGE T&R; operating temperature -40 to 125°C; marking 1HPH · p. 27

Open-source boards using it

19See all 19
  • 4 layers50 × 65 mmFeroFlyF405, the printed circuit board in 3D

    FeroFlyF405

    Ozonised/FeroFlyF405

    FeroFlyF405 an open source STM32F405 based flight controller running INAV

    150 parts44CERN-OHL-P-2.0
  • 2 layers92 × 62.5 mmEthernet, the printed circuit board in 3D

    Ethernet

    rjrouquette/gpsdo

    GPSDO PTP Master

    111 parts11Unlicense
  • 6 layersOpenAquatix Hardware, the printed circuit board in 3D

    OpenAquatix Hardware

    ericvoi/OpenAquatix-Hardware

    OpenAquatix PCB files

    351 parts4CERN-OHL-P-2.0
  • 4 layers53 × 32 mmUbiquitous waddle, the printed circuit board in 3D

    Ubiquitous waddle

    leonwip/ubiquitous-waddle

    Dual channel CANnectivity CAN FD to USB-C adapter

    44 parts3CERN-OHL-P-2.0
  • 4 layers50 × 16 mmSystem board, the printed circuit board in 3D

    System board

    proegssilb/lightsaber-hardware

    PCBs and other files for lightsaber soundboard hardware.

    72 parts2CERN-OHL-S-2.0
  • 4 layers17.5 × 30.5 mmESP32 S3 CAM wifi, the printed circuit board in 3D

    ESP32 S3 CAM wifi

    HexSense-MIT/HS_ESP32_CAM_module

    A custom designed USB camera module, with ESP32-S3R8 + OV2640. This will be used for the HexSenseCAM payload.

    52 parts1
  • 4 layers15.4 × 25.5 mmChiquito, the printed circuit board in 3D

    Chiquito

    devcexx/chiquito

    Smol development / testing board for STM32C071

    17 parts
  • 4 layers1,189 × 841 mmTARS MK2, the printed circuit board in 3D

    TARS MK2

    ISSUIUC/ISS-PCB-Archive

    Archive of PCBs that are more than 1 to 2 years old.

    87 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TLV75733PDRV?

Yes. The symbol is Regulator_Linear:TLV75733PDRV and the footprint Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TLV75733PDRV?

WSON-6(2x2), with 7 pins. Its footprint is drawn on this page.

Where is the TLV75733PDRV datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TLV75733PDRV?

JLCPCB lists it as part C2868428, with 3,096 in stock; the sellers' links on this page open their listings.

What can replace the TLV75733PDRV?

Parts like it in the library: the TLV76733DRVR by Texas Instruments, the TLV76733DRVT by Texas Instruments, the AMS1117-3.3 by Advanced Monolithic Systems and the AMS1117-3.3 by UMW. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TLV75733PDRV?

19 boards in 17 repositories on GitHub; the most starred are listed on this page, with their KiCad files.