Skip to the content
1234567

LP5912-3.3DRVR

Texas InstrumentsExtended

-40℃~+125℃@(Tj) 1 12uVrms 180mV@(500mA) 3.3V 30uA 500mA 6.5V 75dB@(1kHz) Fixed Over Temperature Protection、Reverse connection protection、Soft Start、Short Circuit Protection Positive WSON-6-EP(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
ti/LP5912-3.3DRVR
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
WSON-6-EP(2x2)
Pins
7
In stock
23,622 at JLCPCB (C524780)
Used on
40 open-source boards

Overview

The LP5912-3.3DRVR is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Texas Instruments in a WSON-6-EP(2x2) package with 7 pins. -40℃~+125℃@(Tj) 1 12uVrms 180mV@(500mA) 3.3V 30uA 500mA 6.5V 75dB@(1kHz) Fixed Over Temperature Protection、Reverse connection protection、Soft Start、Short Circuit Protection Positive WSON-6-EP(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (Regulator_Linear:LP5912-3.3DRV, from KiCad's library) and its footprint (Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm, from KiCad's library), ready for a KiCad board. 23,622 are in stock at JLCPCB (part C524780). 40 open-source boards in 36 repositories on GitHub use it.

Symbol

1OUT4EN5GND6IN3PG7EP
Regulator_Linear:LP5912-3.3DRVFrom KiCad's library

Footprint

1234567
Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mmFrom KiCad's library

From the datasheet

12
Supply, least
1.6 V · VIN, recommended operating min · p. 4
Supply, most
6.5 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
7 V · VIN, absolute max · p. 4
Junction, hottest
150 °C · Junction temperature, absolute max · p. 4
Takes working
30 µA · Quiescent current, enabled with no load, typical · p. 5
Takes asleep
200 nA · Shutdown quiescent current, VEN = 0 V, typical · p. 5
Gives
500 mA · Continuous output current, max · p. 4
Current limit
900 mA · Short-circuit current limit at TJ = 25°C, typical · p. 5
Dropout
95 mV · Dropout at 500 mA, 3.3 V output, typical · p. 5
Junction to air (DRV (WSON))
71.2 K/W · Junction-to-ambient thermal resistance, High-K · p. 4
Junction to case (DRV (WSON))
93.7 K/W · Junction-to-case (top) thermal resistance · p. 4
Junction to board (DRV (WSON))
40.7 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

11
Output current
Up to 500 mA · p. 1
Output noise
12 µVRMS typical · p. 1
PSRR
75 dB typical at 1 kHz · p. 1
Output voltage tolerance
±2% for VOUT ≥ 3.3 V · p. 1
Protection
Thermal overload and short circuit · p. 1
Protection
Reverse current · p. 1
Noise bypass capacitor
Not required · p. 1
Output automatic discharge
Fast turnoff · p. 1
Power-good output
140-µs typical delay · p. 1
Soft start
Internal, limits in-rush current · p. 1
Package
WSON (6), 2.00 mm × 2.00 mm · p. 1

Around it

2
cap 1 µF
between IN and GND; Input ceramic capacitor; minimum 0.7 uF specified for stability. · p. 7
cap 1 µF
between OUT and GND; Output ceramic capacitor; stability range 0.7 uF to 10 uF. · p. 7

Specifications

57
ParameterConditionsAs printedPage
Input voltage VINOver operating free-air temperature rangemin -0.3 · max 7 V4
Output voltage VOUTOver operating free-air temperature rangemin -0.3 · max 7 V4
Enable input voltage VENOver operating free-air temperature rangemin -0.3 · max 7 V4
Power Good (PG) pin OFF voltage VPGOver operating free-air temperature rangemin -0.3 · max 7 V4
Junction temperature TJmax 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1000 Vmax 1000 V4
Input supply voltage VINmin 1.6 · max 6.5 V4
Output voltage VOUTmin 0.8 · max 5.5 V4
Enable input voltage VENMaximum is VINmin 0 V4
PG pin OFF voltage VPGmin 0 · max 6.5 V4
Output current IOUTmin 0 · max 500 mA4
Operating junction temperature TJ-MAX-OPmin -40 · max 125 °C4
Junction-to-ambient thermal resistance, High-K RθJADRV (WSON), 6 pins; High-K PCB with two thermal vias under exposed thermal padtyp 71.2 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)DRV (WSON), 6 pinstyp 93.7 °C/W4
Junction-to-board thermal resistance RθJBDRV (WSON), 6 pinstyp 40.7 °C/W4
Junction-to-top characterization parameter ψJTDRV (WSON), 6 pinstyp 2.5 °C/W4
Junction-to-board characterization parameter ψJBDRV (WSON), 6 pinstyp 41.1 °C/W4
Junction-to-case (bottom) thermal resistance RJC(bot)DRV (WSON), 6 pinstyp 11.2 °C/W4
Output voltage tolerance ΔVOUTVOUT(NOM) ≥ 3.3 V; VOUT(NOM) + 0.5 V ≤ VIN ≤ 6.5 V; IOUT = 1 mA to 500 mAmin -2 · max 2 %5
Line regulation ΔVOUTVOUT(NOM) ≥ 1.1V; VOUT(NOM) + 0.5 V ≤ VIN ≤ 6.5 Vtyp 0.8 %/V5
Load regulation ΔVOUTIOUT = 1 mA to 500 mAtyp 0.0022 %/mA5
Short-circuit current limit ISCTJ = 25°C; VOUT pulled to 100 mV below nominal voltagemin 700 · typ 900 · max 1100 mA5
Reverse leakage current IROVEN = VIN = 0 V, VOUT = 5.5 V; measured at IN pintyp 10 · max 150 uA5
Quiescent current IQVEN = 1.3 V, IOUT = 0 mAtyp 30 · max 55 uA5
Quiescent current IQVEN = 1.3 V, IOUT = 500 mAtyp 400 · max 600 uA5
Quiescent current, shutdown mode IQ(SD)VEN = 0 V; –40°C ≤ TJ ≤ 85°Ctyp 0.2 · max 1.5 uA5
Quiescent current, shutdown mode IQ(SD)VEN = 0 V; –40°C ≤ TJ ≤ 125°Ctyp 0.2 · max 5 uA5
Ground current IGVEN = 1.3 V, IOUT = 0 mAtyp 35 uA5
Dropout voltage VDOIOUT = 500 mA, 3.3 V ≤ VOUT(NOM) ≤ 5.5 Vtyp 95 · max 180 mV5
Power Supply Rejection Ratio PSRRƒ = 100 Hz, VOUT ≥ 1.1 V, IOUT = 20 mAtyp 80 dB6
Power Supply Rejection Ratio PSRRƒ = 1 kHz, VOUT ≥ 1.1 V, IOUT = 20 mAtyp 75 dB6
Power Supply Rejection Ratio PSRRƒ = 10 kHz, VOUT ≥ 1.1 V, IOUT = 20 mAtyp 65 dB6
Power Supply Rejection Ratio PSRRƒ = 100 kHz, VOUT ≥ 1.1 V, IOUT = 20 mAtyp 40 dB6
Noise voltage eNIOUT = 1 mA, BW = 10 Hz to 100 kHztyp 12 uVRMS6
Noise voltage eNIOUT = 500 mA, BW = 10 Hz to 100 kHztyp 12 uVRMS6
Thermal shutdown temperature TSDtyp 160 °C6
Thermal shutdown hysteresis THYStyp 15 °C6
OFF Threshold VEN(OFF)VIN = 1.6 V to 6.5 V; VEN falling until device is disabledmax 0.3 V6
ON Threshold VEN(ON)1.6 V ≤ VIN ≤ 6.5 V; VEN rising until device is enabledmin 1.3 V6
Input current at EN pin IENVEN = 6.5 V, VIN = 6.5 Vtyp 2.5 uA6
Input current at EN pin IENVEN = 0 V, VIN = 3.3 Vtyp 0.001 uA6
PG high threshold (% of nominal VOUT) PGHTHtyp 94 %6
PG low threshold (% of nominal VOUT) PGLTHtyp 90 %6
PG pin low-level output voltage VOL(PG)VOUT < PGLTH, sink current = 1 mAmax 100 mV6
PG pin leakage current IlKG(PG)VOUT < PGHTH, VPG = 6.5 Vmax 1 uA6
PG delay time tPGDTime from VOUT > PG threshold to PG togglingtyp 140 us6
Line transients ΔVOUTVIN falling; VOUT(NOM) ≥ 1.1 V; VIN = (VOUT(NOM) + 1.1 V) to (VOUT(NOM) + 0.5 V); VIN tfall = 30 ustyp -1 mV7
Load transients ΔVOUTIOUT = 5 mA to 500 mA; IOUT trise = 10 usmin -45 mV7
Load transients ΔVOUTIOUT = 500 mA to 5 mA; IOUT tfall = 10 usmax 45 mV7
Overshoot on start-up ΔVOUTStated as a percentage of VOUT(NOM)max 5 %7
Turnon time tONTime from VEN > VEN(ON) to VOUT = 95% of VOUT(NOM)typ 200 us7
Output discharge pull-down resistance RADVEN = 0 V, VIN = 3.6 Vtyp 100 Ω7
Input capacitance CINCapacitance for stabilitymin 0.7 · typ 1 uF7
Output capacitance COUTCapacitance for stabilitymin 0.7 · typ 1 · max 10 uF7
Output voltage ESRCapacitance for stabilitymin 5 · max 500 mΩ7

Pins, by the datasheet

6
1 OUT
Regulated output voltage. · p. 3
2 NC
No internal connection; leave open or connect to ground. · p. 3
3 PG
Power-good indicator; requires external pullup. · p. 3
4 EN
Enable input; logic high turns device on, logic low turns device off; internal 3-MΩ pulldown. · p. 3
5 GND
Ground. · p. 3
6 IN
Unregulated input voltage. · p. 3

Open-source boards using it

40See all 40
  • 6 layers26.9 × 26.9 mmOpenFC, the printed circuit board in 3D

    OpenFC

    OpenDrone-hw/OpenFC-Lite-Mini

    Open-source Betaflight flight controller. RP2354A, 20x20 mm, 6-layer, 3-6S, CERN-OHL-S-2.0.

    131 parts147CERN-OHL-S-2.0
  • 6 layers37.9 × 37.9 mmOpenFC, the printed circuit board in 3D

    OpenFC

    OpenDrone-hw/OpenFC-Lite

    Open-source Betaflight flight controller. RP2354B, 30.5x30.5 mm, 6-layer, 3-8S, CERN-OHL-S-2.0.

    164 parts85CERN-OHL-S-2.0
  • 2 layers212.5 × 99.5 mmOssc pro, the printed circuit board in 3D

    Ossc pro

    marqs85/ossc_pro_hw

    OSSC Pro HW files

    499 parts31CERN-OHL-P-2.0
  • 4 layers62.8 × 61.7 mmCf mp3-player, the printed circuit board in 3D

    Cf mp3-player

    will127534/cf-mp3-player

    A simple MP3/WAV/FLAC player using CF card

    119 parts16MIT
  • 8 layers28.9 × 28.9 mmOpenAIO Whoop, the printed circuit board in 3D

    OpenAIO Whoop

    OpenDrone-hw/OpenAIO-Whoop

    Open-source 1S whoop AIO: flight controller, 4-channel brushless ESC, ExpressLRS receiver and analog VTX, 25.5x25.5 mm. Planned.

    249 parts13CERN-OHL-S-2.0
  • 4 layers53 × 40 mmSB main board, the printed circuit board in 3D

    SB main board

    CharlieYu4994/SB_CAN

    为 Voron Design 的 StealthBurner 设计的 CAN 总线工具头板

    95 parts10
  • 8 layers38 × 38 mmKolibri v0.5, the printed circuit board in 3D

    Kolibri v0.5

    bastian2001/Kolibri-FC-Hardware

    Hardware for the Kolibri Flight Controller. 30mm/20mm FC with RP2350 + ELRS onboard

    221 parts8GPL-3.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the LP5912-3.3DRVR?

Yes. The symbol is Regulator_Linear:LP5912-3.3DRV and the footprint Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LP5912-3.3DRVR?

WSON-6-EP(2x2), with 7 pins. Its footprint is drawn on this page.

Where is the LP5912-3.3DRVR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the LP5912-3.3DRVR?

JLCPCB lists it as part C524780, with 23,622 in stock; the sellers' links on this page open their listings.

What can replace the LP5912-3.3DRVR?

Parts like it in the library: the TLV76733DRVR by Texas Instruments, the TLV75533PDRV by Texas Instruments, the TLV75733PDRV by Texas Instruments and the LP5912-3.3DRVT by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the LP5912-3.3DRVR?

40 boards in 36 repositories on GitHub; the most starred are listed on this page, with their KiCad files.