Skip to the content
12345678

THVD1450D

Texas InstrumentsExtended

-40℃~+125℃ 1 1 256 3V~5.5V 3mA 50Mbps Half-Duplex Transceiver ±18kV SOIC-8 RS-485 / RS-422 ICs ROHS

Part id
ti/THVD1450D
Category
RS 485, RS 422 ICs
Package
SOIC-8
Pins
8
In stock
2,836 at JLCPCB (C2671361)
Used on
15 open-source boards

Overview

The THVD1450D is a RS 485, RS 422 IC made by Texas Instruments in a SOIC-8 package with 8 pins. -40℃~+125℃ 1 1 256 3V~5.5V 3mA 50Mbps Half-Duplex Transceiver ±18kV SOIC-8 RS-485 / RS-422 ICs ROHS.

PCBKit's library has its KiCad symbol (Interface_UART:THVD1450D, from KiCad's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 2,836 are in stock at JLCPCB (part C2671361). 15 open-source boards in 13 repositories on GitHub use it.

Symbol

1RO2RE3DE4DI5GND6A7B8VCC
Interface_UART:THVD1450DFrom KiCad's library

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

15
Supply, least
3 V · VCC, recommended operating min · p. 9
Supply, most
5.5 V · VCC, recommended operating max · p. 9
Supply, absolute maximum
7 V · VCC, absolute max · p. 8
Works from
-40 °C · Operating ambient temperature min · p. 9
Works up to
125 °C · Operating ambient temperature max · p. 9
Junction, hottest
150 °C · Junction temperature max · p. 9
Takes working
2.4 mA · VCC, driver and receiver enabled, no load, 5 V, typical · p. 10
Takes at most
3 mA · VCC, driver and receiver enabled, no load, max · p. 10
Takes asleep
100 nA · VCC, driver and receiver disabled, no load, typical · p. 10
A pin gives at most
24 mA · Receiver output source or sink current, absolute max · p. 8
Junction to air (D (SOIC))
114.3 K/W · Junction-to-ambient thermal resistance · p. 9
Junction to case (D (SOIC))
56.7 K/W · Junction-to-case (top) thermal resistance · p. 9
Junction to board (D (SOIC))
57.7 K/W · Junction-to-board thermal resistance · p. 9
Data rate, most
50 Mbit/s · THVD1450 signaling rate max · p. 9
Edge
2 ns · Receiver output rise/fall time, 5 V, typical · p. 11

What it is and has

7
Standard
TIA/EIA-485A · p. 1
Bus loading
1/8 unit load, up to 256 bus nodes · p. 1
Protection
Open-circuit, short-circuit and idle-bus failsafe · p. 1
Hot plug
Glitch-free power-up and power-down · p. 1
Bus I/O ESD protection
±30 kV HBM · p. 1
Bus I/O ESD protection
±18 kV IEC 61000-4-2 contact discharge · p. 1
Bus I/O ESD protection
±25 kV IEC 61000-4-2 air discharge · p. 1

Specifications

66
ParameterConditionsAs printedPage
Supply voltage VCCOver operating free-air temperature rangemin -0.5 · max 7 V8
Bus voltageRange at any bus pin (A, B, Y, or Z) as differential or common-mode with respect to GNDmin -18 · max 18 V8
Input voltageRange at any logic pin (D, DE, or RE)min -0.3 · max 5.7 V8
Receiver output current IOOver operating free-air temperature rangemin -24 · max 24 mA8
Storage temperature rangemin -65 · max 150 ℃8
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; bus pins and GND; ±30 kVmax 30 kV8
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; all other pins; ±8 kVmax 8 kV8
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC JESD22-C101; all pins; ±1.5 kVmax 1.5 kV8
Electrostatic discharge V(ESD)Machine model (MM), per JEDEC JESD22-A115-A; all pins; ±200 Vmax 200 V8
Electrostatic discharge V(ESD)Contact discharge, per IEC 61000-4-2; bus pins and GND; ±18 kVmax 18 kV8
Electrostatic discharge V(ESD)Air-gap discharge, per IEC 61000-4-2; bus pins and GND; ±25 kVmax 25 kV8
Electrical fast transient V(EFT)Per IEC 61000-4-4; bus pins and GND; ±4 kVmax 4 kV8
Supply voltage VCCOver operating free-air temperature rangemin 3 · max 5.5 V9
Input voltage at any bus terminal VImin -15 · max 15 V9
High-level input voltage (driver, driver enable, and receiver enable inputs) VIHMaximum: VCCmin 2 V9
Low-level input voltage (driver, driver enable, and receiver enable inputs) VILmin 0 · max 0.8 V9
Differential input voltage VIDmin -15 · max 15 V9
Output current, driver IOmin -60 · max 60 mA9
Output current, receiver IORmin -8 · max 8 mA9
Differential load resistance RLmin 54 Ω9
Signaling rate: THVD1450, THVD1451, THVD1452 1/tUITHVD1450max 50 Mbps9
Operating ambient temperature TAmin -40 · max 125 ℃9
Junction temperature TJmin -40 · max 150 ℃9
Junction-to-ambient thermal resistance RθJATHVD1450, D (SOIC), 8 PINStyp 114.3 °C/W9
Junction-to-case (top) thermal resistance RθJC(top)THVD1450, D (SOIC), 8 PINStyp 56.7 °C/W9
Junction-to-board thermal resistance RθJBTHVD1450, D (SOIC), 8 PINStyp 57.7 °C/W9
Junction-to-top characterization parameter ΨJTTHVD1450, D (SOIC), 8 PINStyp 12.8 °C/W9
Junction-to-board characterization parameter ΨJBTHVD1450, D (SOIC), 8 PINStyp 57 °C/W9
Power dissipation PDTHVD145x devices; driver and receiver enabled, VCC = 5.5 V, TA = 125°C, 50% duty cycle square wave at 50Mbps; unterminated: RL = 300 Ω, CL = 50 pFtyp 360 mW9
Power dissipation PDTHVD145x devices; driver and receiver enabled, VCC = 5.5 V, TA = 125°C, 50% duty cycle square wave at 50Mbps; RS-422 load: RL = 100 Ω, CL = 50 pFtyp 320 mW9
Power dissipation PDTHVD145x devices; driver and receiver enabled, VCC = 5.5 V, TA = 125°C, 50% duty cycle square wave at 50Mbps; RS-485 load: RL = 54 Ω, CL = 50 pFtyp 330 mW9
Driver differential output voltage magnitude |VOD|RL = 60 Ω, -15 V ≤ Vtest ≤ 15 V; see Figure 20 and footnote (1)min 1.5 · typ 3.5 V10
Driver differential output voltage magnitude |VOD|RL = 60 Ω, -15 V ≤ Vtest ≤ 15 V, 4.5 V ≤ VCC ≤ 5.5 V; see Figure 20min 2.1 V10
Driver differential output voltage magnitude |VOD|RL = 100 Ω; see Figure 21min 2 · typ 4 V10
Driver differential output voltage magnitude |VOD|RL = 54 Ω; see Figure 21min 1.5 · typ 3.5 V10
Change in differential output voltage Δ|VOD|min -200 · max 200 mV10
Common-mode output voltage VOCRL = 54 Ω; see Figure 21; typical: VCC/2min 1 · max 3 V10
Change in steady-state common-mode output voltage ΔVOC(SS)min -200 · max 200 mV10
Short-circuit output current IOSDE = VCC, -7 V ≤ VO ≤ 12 Vmin -250 · max 250 mA10
Bus input current IIDE = 0 V, VCC = 0 V or 5.5 V, VI = 12Vtyp 50 · max 125 uA10
Bus input current IIDE = 0 V, VCC = 0 V or 5.5 V, VI = -7Vmin -100 · typ -65 uA10
Bus input current IIDE = 0 V, VCC = 0 V or 5.5 V, VI = 15Vtyp 60 · max 125 uA10
Bus input current IIDE = 0 V, VCC = 0 V or 5.5 V, VI = -15Vmin -200 · typ -130 uA10
Positive-going input threshold voltage VTH+Over common-mode range of ± 15 V; minimum: see footnote (2)typ -100 · max -20 mV10
Negative-going input threshold voltage VTH-Over common-mode range of ± 15 V; maximum: see footnote (2)min -200 · typ -130 mV10
Input hysteresis VHYSOver common-mode range of ± 15 Vtyp 30 mV10
Output low voltage VOLIOL = 8 mAtyp 0.2 · max 0.4 V10
Output high-impedance current IOZRVO = 0 V or VCC, RE = VCCmin -1 · max 1 uA10
Input current (D, DE, RE) IIN3 V ≤ VCC ≤ 5.5 V, 0 V ≤ VIN ≤ VCCmin -6.2 · max 6.2 uA10
Supply current (quiescent) ICCDriver and receiver enabled; RE = 0 V, DE = VCC, no loadtyp 2.4 · max 3 mA10
Supply current (quiescent) ICCDriver enabled, receiver disabled; RE = VCC, DE = VCC, no loadtyp 2 · max 2.5 mA10
Supply current (quiescent) ICCDriver disabled, receiver enabled; RE = 0 V, DE = 0 V, no loadtyp 700 · max 960 uA10
Supply current (quiescent) ICCDriver and receiver disabled; RE = VCC, DE = 0 V, D = open, no loadtyp 0.1 · max 1 uA10
Thermal shutdown temperature TSDtyp 170 ℃10
Differential output rise/fall time tr, tfDriver: THVD1450; RL = 54 Ω, CL = 50 pF; see Figure 22; typical at 25°C, VCC = 5 Vmin 1 · typ 3 · max 6 ns11
Propagation delay tPHL, tPLHDriver: THVD1450; RL = 54 Ω, CL = 50 pF; see Figure 22; typical at 25°C, VCC = 5 Vmin 3 · typ 10 · max 20 ns11
Pulse skew, |tPHL – tPLH| tSK(P)Driver: THVD1450; RL = 54 Ω, CL = 50 pF; see Figure 22max 3.5 ns11
Disable time tPHZ, tPLZDriver: THVD1450; typical at 25°C, VCC = 5 Vtyp 15 · max 25 ns11
Enable time tPZH, tPZLDriver: THVD1450; RE = 0 V; see Figures 23 and 24; typical at 25°C, VCC = 5 Vtyp 20 · max 50 ns11
Enable time tPZH, tPZLDriver: THVD1450; RE = VCC; see Figures 23 and 24; typical at 25°C, VCC = 5 Vtyp 2.5 · max 10 us11
Output rise/fall time tr, tfReceiver: THVD1450; CL = 15 pF; see Figure 25; typical at 25°C, VCC = 5 Vtyp 2 · max 6 ns11
Propagation delay tPHL, tPLHReceiver: THVD1450; CL = 15 pF; see Figure 25; typical at 25°C, VCC = 5 Vtyp 25 · max 40 ns11
Pulse skew, |tPHL – tPLH| tSK(P)Receiver: THVD1450; CL = 15 pF; see Figure 25max 3.5 ns11
Disable time tPHZ, tPLZReceiver: THVD1450; typical at 25°C, VCC = 5 Vtyp 14 · max 28 ns11
Enable time tPZH(1), tPZL(1)Receiver: THVD1450; DE = VCC; see Figure 26; typical at 25°C, VCC = 5 Vtyp 50 · max 110 ns11
Enable time tPZH(2), tPZL(2)Receiver: THVD1450; DE = 0V; see Figure 27; typical at 25°C, VCC = 5 Vtyp 4 · max 14 us11

Pins, by the datasheet

8
1 R
Receive data output. · p. 5
2 RE
Receiver enable, active low, with 2-MΩ internal pull-up. · p. 5
3 DE
Driver enable, active high, with 2-MΩ internal pull-down. · p. 5
4 D
Driver data input. · p. 5
5 GND
Device ground. · p. 5
6 A
Bus I/O port, A, complementary to B. · p. 5
7 B
Bus I/O port, B, complementary to A. · p. 5
8 VCC
3.3-V to 5-V supply. · p. 5

Open-source boards using it

15See all 15
  • 4 layers50 × 50 mmIndustrial Encoder Node, the printed circuit board in 3D

    Industrial Encoder Node

    anushakatikireddy/STM32-Industrial_Encoder_Node

    Compact industrial encoder node designed for reliable position sensing and communication in robotics and motion control applications, developed as a complete hardware solution in KiCad.

    49 parts
  • 4 layers94 × 94 mmWalter feels, the printed circuit board in 3D

    Walter feels

    benmcnelly/walter-hardware

    This repository contains all hardware information about Walter and shields

    154 partsGPL-3.0
  • 4 layers230 × 135 mmVancontroller, the printed circuit board in 3D

    Vancontroller

    Camperlux/vancontroller

    VanController: ESP32-S3 12 V campervan controller board (6 fused relays, 6 PWM dimmers, CAN, RS485, GPS) - KiCad 10 design, manufacturing files and enclosure. Free for non-commercial use.

    259 parts
  • 2 layers50 × 50 mmDigital Humidity Gauge, the printed circuit board in 3D

    Digital Humidity Gauge

    embeddedalpha/Digital-Humidity-Gauge

    🎯 Dry‑bulb Temperature 🎯 Relative humidity 🎯 Barometric pressure 🎯 Saturation vapour pressure 🎯 Actual vapour pressure 🎯 Humidity (mixing) ratio 🎯 Absolute humidity 🎯 Dew‑point temperature 🎯 Wet‑bulb…

    68 parts
  • 4 layers61.9 × 84.4 mmFastStepper, the printed circuit board in 3D

    FastStepper

    harp-tech/device.faststepper

    A fast moving stepper motor controller device, with acceleration, jerk control, and end stop support

    141 parts
  • 4 layers104 × 104 mmHomeAutomation pi, the printed circuit board in 3D

    HomeAutomation pi

    PragyanSenDeka/RaspberryPiPicoBasedHomeAutomationPCB

    Home automation node based on Raspberry Pi Pico W with WiFi and RS485/MODBUS. Features DIP-switch addressing, SHT31 temperature/humidity sensor, QWIIC I2C, RGB LED, buttons, SPI expansion, and a 230V 16A relay.

    58 parts
  • 4 layers100 × 100 mmArtnet node poe, the printed circuit board in 3D

    Artnet node poe

    Tommie1236/artnet-node-poe

    134 partsMIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the THVD1450D?

Yes. The symbol is Interface_UART:THVD1450D and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the THVD1450D?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the THVD1450D datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the THVD1450D?

JLCPCB lists it as part C2671361, with 2,836 in stock; the sellers' links on this page open their listings.

What can replace the THVD1450D?

Parts like it in the library: the SP3485EN-L/TR by MaxLinear, the SP485EEN-L/TR by MaxLinear, the SN75176BD by Texas Instruments and the MAX485ESA+T by Maxim Integrated (Analog Devices). Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the THVD1450D?

15 boards in 13 repositories on GitHub; the most starred are listed on this page, with their KiCad files.