
SP3485EN-L/TR
MaxLinearJLCPCB basic
-40℃~+85℃ 1 1 10Mbps 2mA 3.3V 32 Half-Duplex Transceiver SOIC-8 RS-485 / RS-422 ICs ROHS
- Part id
- maxlinear/SP3485EN-L/TR
- Category
- RS 485, RS 422 ICs
- Package
- SOIC-8
- Pins
- 8
- In stock
- 339,587 at JLCPCB (C8963)
- Used on
- 24 open-source boards
Overview
The SP3485EN-L/TR is a RS 485, RS 422 IC made by MaxLinear in a SOIC-8 package with 8 pins. -40℃~+85℃ 1 1 10Mbps 2mA 3.3V 32 Half-Duplex Transceiver SOIC-8 RS-485 / RS-422 ICs ROHS.
PCBKit's library has its KiCad symbol (Interface_UART:SP3485EN, from KiCad's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 339,587 are in stock at JLCPCB (part C8963). 24 open-source boards in 21 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
8- Supply, absolute maximum
- 6 V · VCC, absolute maximum · p. 2
- Works from
- -40 °C · SP3485EN-L/TR, minimum operating temperature · p. 9
- Works up to
- 85 °C · SP3485EN-L/TR, maximum operating temperature · p. 9
- Takes working
- 1 mA · VCC, typical no-load supply current, driver enabled · p. 3
- Takes working
- 800 µA · VCC, typical no-load supply current, receiver enabled and driver disabled · p. 3
- Takes at most
- 2 mA · VCC, max no-load supply current, driver enabled · p. 3
- Data rate, most
- 10 Mbit/s · Driver maximum data rate · p. 2
- Edge
- 5 ns · Driver typical rise or fall time, 10%–90% · p. 2
What it is and has
9- Interface
- RS-485 and RS-422 transceiver · p. 1
- Supply
- Single +3.3V · p. 1
- Logic compatibility
- +5.0V logic · p. 1
- Enable controls
- Driver/Receiver Enable · p. 1
- Common-mode input voltage range
- -7V to +12V · p. 1
- Bus capacity
- Up to 32 transceivers · p. 1
- Pinout compatibility
- Industry standard 75176 · p. 1
- Protection
- Driver output short-circuit protection · p. 1
- Package
- 8-pin NSOIC · p. 9
Specifications
47| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| VCC VCC | max 6 V | 2 | |
| Input Voltages, Logic | min -0.3 · max 6 V | 2 | |
| Input Voltages, Drivers | min -0.3 · max 6 V | 2 | |
| Input Voltages, Receivers | Rating printed as +/-15V | min -15 · max 15 V | 2 |
| Output Voltages, Drivers | Rating printed as +/-15V | min -15 · max 15 V | 2 |
| Output Voltages, Receivers | min -0.3 · max 6 V | 2 | |
| Storage Temperature | min -65 · max 150 ˚C | 2 | |
| Power Dissipation | 8-pin NSOIC | max 600 mW | 2 |
| Power Dissipation derating | 8-pin NSOIC; above +70ºC | max 6.9 mW/ºC | 2 |
| Differential Output Voltage | SP3485 DRIVER; With Load; R = 50Ω (RS-422); Figure 1; maximum Vcc | min 2 Volts | 2 |
| Differential Output Voltage | SP3485 DRIVER; With Load; R = 27Ω (RS-485); Figure 1; maximum Vcc | min 1.5 Volts | 2 |
| Change in Magnitude of Driver Differential Output Voltage for Complimentary states | SP3485 DRIVER; R = 27Ω or R = 50Ω; Figure 1 | max 0.2 Volts | 2 |
| Driver Common Mode Output Voltage | SP3485 DRIVER; R = 27Ω or R = 50Ω; Figure 1 | max 3 Volts | 2 |
| Input High Voltage | SP3485 DRIVER; Applies to DE, DI, RE | min 2 Volts | 2 |
| Input Low Voltage | SP3485 DRIVER; Applies to DE, DI, RE | max 0.8 Volts | 2 |
| Input Current | SP3485 DRIVER; Applies to DE, DI, RE; maximum printed as +/-10 | max 10 uA | 2 |
| Driver Short Circuit Current VOUT = HIGH | -7V ≤ VO ≤ +12V; Figure 8; maximum printed as +/-250 | max 250 mA | 2 |
| Driver Short Circuit Current VOUT = LOW | -7V ≤ VO ≤ +12V; Figure 8; maximum printed as +/-250 | max 250 mA | 2 |
| Maximum Data Rate | SP3485 DRIVER; RE = VCC, DE = VCC | min 10 Mbps | 2 |
| Driver Input to Output, tPLH tPLH | Figures 2 & 9 | min 20 · typ 40 · max 60 ns | 2 |
| Driver Input to Output, tPHL tPHL | Figures 2 & 9 | min 20 · typ 40 · max 60 ns | 2 |
| Differential Driver Skew | |tDO1- tDO2|, Figures 2 and 10 | typ 2 · max 10 ns | 2 |
| Driver Rise or Fall Time | From 10%-90%; Figures 3 and 10 | typ 5 · max 20 ns | 2 |
| Driver Enable to Output High | Figures 4 and 11 | typ 52 · max 120 ns | 3 |
| Driver Enable to Output Low | Figures 5 and 11 | typ 60 · max 120 ns | 3 |
| Driver Disable Time from Low | Figures 5 and 11 | typ 40 · max 120 ns | 3 |
| Driver Disable Time from High | Figures 4 and 11 | typ 60 · max 120 ns | 3 |
| Differential Input Threshold | SP3485 RECEIVER; -7V ≤ VCM ≤ +12V | min -0.2 · max 0.2 Volts | 3 |
| Input Hysteresis | SP3485 RECEIVER; VCM = 0V | typ 20 mV | 3 |
| Output Voltage LOW | SP3485 RECEIVER; VID = -200mV, 2.5mA | max 0.4 Volts | 3 |
| Three-State (High Impedance) Output Current | SP3485 RECEIVER; 0V ≤ VO ≤ VCC; RE = VCC; maximum printed as +/-1 | max 1 uA | 3 |
| Input Resistance | SP3485 RECEIVER; -7V ≤ VCM ≤ +12V | min 12 · typ 15 kΩ | 3 |
| Input Current (A, B); VIN = 12V | SP3485 RECEIVER; DE = 0V, VCC = 0V or 3.6V, VIN = 12V | max 1 mA | 3 |
| Input Current (A, B); VIN = -7V | SP3485 RECEIVER; DE = 0V, VCC = 0V or 3.6V, VIN = -7V | max -0.8 mA | 3 |
| Short Circuit Current | SP3485 RECEIVER; 0V ≤ VCM ≤ VCC | min 7 · max 60 mA | 3 |
| Maximum Data Rate | SP3485 RECEIVER; RE = 0V, DE = 0V | min 10 Mbps | 3 |
| Receiver Input to Output, tPLH tPLH | Figures 6 and 12 | min 40 · typ 70 · max 100 ns | 3 |
| Receiver Input to Output, tPLH tPLH | TAMB = +25°C, Vcc = 3.3V, Figures 6 and 12 | max 70 ns | 3 |
| Receiver Input to Output, tPHL tPHL | Figures 6 and 12 | min 40 · typ 70 · max 100 ns | 3 |
| Receiver Input to Output, tPHL tPHL | TAMB = +25°C, Vcc = 3.3V, Figures 6 and 12 | max 70 ns | 3 |
| Differential Receiver Skew tRSKEW | tRSKEW = |tRPHL- tRPLH|, Figures 6 and 12 | typ 4 ns | 3 |
| Receiver Enable to Output Low | Figures 7 and 13, S1 closed, S2 open | typ 35 · max 60 ns | 3 |
| Receiver Enable to Output High | Figures 7 and 13, S2 closed, S1 open | typ 35 · max 60 ns | 3 |
| Receiver Disable from Low | Figures 7 and 13, S1 closed, S2 open | typ 35 · max 60 ns | 3 |
| Receiver Disable from High | Figures 7 and 13, S2 closed, S1 open | typ 35 · max 60 ns | 3 |
| Supply Current , No Load | RE, DI = 0V or VCC ; DE = VCC | typ 1000 · max 2000 uA | 3 |
| Supply Current , No Load | RE = 0V, DI = 0V or VCC, DE = 0V | typ 800 · max 1500 uA | 3 |
Pins, by the datasheet
8- 1 RO
- Receiver output. · p. 4
- 2 RE
- Receiver Output Enable Active LOW. · p. 4
- 3 DE
- Driver Output Enable Active HIGH. · p. 4
- 4 DI
- Driver Input. · p. 4
- 5 GND
- Ground Connection. · p. 4
- 6 A
- Non-Inverting Driver Output/Receiver Input. · p. 4
- 7 B
- Inverting Driver Output/Receiver Input. · p. 4
- 8 Vcc
- Positive Supply. · p. 4
Ordering codes, by the datasheet
4- SP3485CN-L
- 8-pin NSOIC · 0°C to +70°C temperature range · p. 9
- SP3485CN-L/TR
- 8-pin NSOIC · 0°C to +70°C temperature range; Tape and Reel · p. 9
- SP3485EN-L
- 8-pin NSOIC · -40°C to +85°C temperature range · p. 9
- SP3485EN-L/TR
- 8-pin NSOIC · -40°C to +85°C temperature range; Tape and Reel · p. 9
- 4 layers85 × 56 mm

- 4 layers85 × 113 mm

- 4 layers267 × 75 mm

Fracture
SharKingStudios/Fracture
An infinitely expandable, velocity sensing split midi keyboard.
208 parts10MIT - 2 layers62 × 208.5 mm

Combined
wr/airwriter
Print to vintage Apple printers from modern devices over AirPrint, or from a vintage Mac over AppleTalk.
154 parts7 - 2 layers100 × 75 mm

Display
DLaxV-Community-Projects-Hub/Open-Shot-Clock
Build your own DIY Shot Clock
209 parts5CERN-OHL-P-2.0 - 4 layers95.6 × 86.1 mm

ELS project
jonasnic/Dreimaskin-ELS
this will contain everything in the Electronic lead screw project
83 parts1 - 2 layers55 × 73.5 mm

Pcb dezentral
petermaerki/puenterswis_heizung_2023_git
Puenterswis Heizungsersatz, Steuerung Anlage mit Oekofen Kaskade Pellematic Maxi PESK
98 parts1 - 2 layers100 × 100 mm

Pcb moduloDidaticoSCADA
wvianna/pcb-moduloDidatico-SCADA-IoT
Projeto de uma PCB para utilização de protocolos: Modbus RTU, Modbus TCP, MQTT, OPC UA pub/sub. Finalidade didática. O firmware também está implementado.
98 parts1
Parts like it
8SP485EEN-L/TR
SOIC-8-40℃~+85℃ 1 1 10Mbps 4.75V~5.25V 900uA Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHSMaxLinearRS-485 / RS-422 ICsSN75176BD
SOIC-80℃~+70℃ 1 1 4.75V~5.25V Transceiver SOIC-8 RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsMAX485ESA+T
SOIC-8-40℃~+85℃ 1 1 2.5Mbps 4.75V~5.25V Transceiver SOIC-8 RS-485 / RS-422 ICs ROHSMaxim Integrated (Analog Devices)RS-485 / RS-422 ICsMAX13487EESA+T
SOIC-8-40℃~+85℃ 1 1 128 4.5mA 4.75V~5.25V 500Kbps Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHSMaxim Integrated (Analog Devices)RS-485 / RS-422 ICsTHVD2450D
SOIC-8-40℃~+125℃ 1 1 256 3V~5.5V 50Mbps Half-Duplex Transceiver ±16kV SOIC-8 RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsTP8485E-SR
SOIC-8-40℃~+125℃ 1 1 1.4mA 250Kbps 256 3V~5.5V Transceiver ±18kV SOIC-8 RS-485 / RS-422 ICs ROHS3PEAKRS-485 / RS-422 ICsSP3078EEN-L/TR
SOIC-8-40℃~+85℃ 1 1 1.5mA 16Mbps 256 3.3V Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHSMaxLinearRS-485 / RS-422 ICsBL3085B
SOIC-8SOP-8L RS-485 / RS-422 ICs ROHSBLRS-485 / RS-422 ICs
Questions
Is there a KiCad symbol and footprint for the SP3485EN-L/TR?
Yes. The symbol is Interface_UART:SP3485EN and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the SP3485EN-L/TR?
SOIC-8, with 8 pins. Its footprint is drawn on this page.
Where is the SP3485EN-L/TR datasheet?
MaxLinear publishes it: the Datasheet link on this page opens it.
Where can I order the SP3485EN-L/TR?
JLCPCB lists it as part C8963, with 339,587 in stock; the sellers' links on this page open their listings.
What can replace the SP3485EN-L/TR?
Parts like it in the library: the SP485EEN-L/TR by MaxLinear, the SN75176BD by Texas Instruments, the MAX485ESA+T by Maxim Integrated (Analog Devices) and the MAX13487EESA+T by Maxim Integrated (Analog Devices). Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the SP3485EN-L/TR?
24 boards in 21 repositories on GitHub; the most starred are listed on this page, with their KiCad files.