
SP485EEN-L/TR
MaxLinearJLCPCB basic
-40℃~+85℃ 1 1 10Mbps 4.75V~5.25V 900uA Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHS
- Part id
- maxlinear/SP485EEN-L/TR
- Category
- RS 485, RS 422 ICs
- Package
- SOIC-8
- Pins
- 8
- In stock
- 304,404 at JLCPCB (C6855)
- Used on
- 5 open-source boards
Overview
The SP485EEN-L/TR is a RS 485, RS 422 IC made by MaxLinear in a SOIC-8 package with 8 pins. -40℃~+85℃ 1 1 10Mbps 4.75V~5.25V 900uA Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHS.
PCBKit's library has its KiCad symbol (JLCPCB-Interface:Transceiver, RS485/422, 10Mbps, SP485EEN-L/TR, from Cdfer) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 304,404 are in stock at JLCPCB (part C6855). 5 open-source boards in 2 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
8- Supply, least
- 4.75 V · VCC, recommended operating min · p. 4
- Supply, most
- 5.25 V · VCC, recommended operating max · p. 4
- Supply, absolute maximum
- 7 V · VCC, absolute max · p. 2
- Works from
- -40 °C · Industrial (_E_), operating ambient min · p. 4
- Works up to
- 85 °C · Industrial (_E_), operating ambient max · p. 4
- Takes working
- 600 µA · VCC, receiver enabled and driver disabled, no load, typical · p. 4
- Data rate, most
- 10 Mbit/s · Receiver maximum data rate, RE = 0V, DE = 0V · p. 3
- Edge
- 15 ns · Driver rise or fall time, typical, RDIFF = 54Ω, CL1 = CL2 = 100pF · p. 3
What it is and has
4- Supply
- 5V only · p. 1
- Technology
- Low power BiCMOS · p. 1
- Interface
- Half-duplex RS-485 / RS-422 · p. 7
- Receiver fail-safe
- Receiver output HIGH when input is left unconnected · p. 7
Specifications
52| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| VCC VCC | max 7 V | 2 | |
| Input Voltages Logic | Upper limit: VCC + 0.5V | min -0.3 V | 2 |
| Input Voltages Drivers | Upper limit: VCC + 0.5V | min -0.3 V | 2 |
| Input Voltages Receivers | ±15V | min -15 · max 15 V | 2 |
| Output Voltages Logic | Upper limit: VCC + 0.5V | min -0.3 V | 2 |
| Output Voltages Drivers | ±15V | min -15 · max 15 V | 2 |
| Output Voltages Receivers | Upper limit: VCC + 0.5V | min -0.3 V | 2 |
| Storage Temperature | min -65 · max 150 ˚C | 2 | |
| Power Dissipation | 8-pin NSOIC; derate 6.60mW/°C above +70°C | max 550 mW | 2 |
| HBM - Human Body Model | A and B pins; ±15kV | max 15 kV | 2 |
| HBM - Human Body Model | All other pins; ±3kV | max 3 kV | 2 |
| IEC61000-4-2 Air Discharge | A and B pins; ±15kV | max 15 kV | 2 |
| IEC61000-4-2 Contact Discharge | A and B pins; ±8kV | max 8 kV | 2 |
| Differential output voltage | With load; R = 50Ω (RS-422); Figure 1; maximum VCC | min 2 V | 2 |
| Differential output voltage | With load; R = 27Ω (RS-485); Figure 1; maximum VCC | min 1.5 V | 2 |
| Change in magnitude of driver differential output voltage for complimentary states | R = 27Ω or R = 50Ω; Figure 1 | max 0.2 V | 2 |
| Driver common-mode output voltage | R = 27Ω or R = 50Ω; Figure 1 | max 3 V | 2 |
| Input high voltage | Applies to DE, DI, RE | min 2 V | 2 |
| Input low voltage | Applies to DE, DI, RE | max 0.8 V | 2 |
| Input current | Applies to DE, DI, RE; maximum magnitude ±10uA | max 10 uA | 2 |
| Driver short circuit current | VOUT = HIGH; -7V ≤ VO ≤ 12V; maximum magnitude ±250mA | max 250 mA | 2 |
| Driver short circuit current | VOUT = LOW; -7V ≤ VO ≤ 12V; maximum magnitude ±250mA | max 250 mA | 2 |
| Maximum data rate | Driver; RE = 5V, DE = 5V; RDIFF = 54Ω, CL1 = CL2 = 100pF | min 10 Mbps | 3 |
| Driver input to output, tPLH tPLH | See Figures 3 & 5, RDIFF = 54Ω, CL1 = CL2 = 100pF | typ 30 · max 60 ns | 3 |
| Driver input to output, tPHL tPHL | See Figures 3 & 5, RDIFF = 54Ω, CL1 = CL2 = 100pF | typ 30 · max 60 ns | 3 |
| Driver skew tSKEW | See Figures 3 and 5, tSKEW = |tDPHL - tDPLH| | typ 5 · max 10 ns | 3 |
| Driver rise or fall time | From 10%-90%; RDIFF = 54Ω; CL1 = CL2 = 100pF; See Figures 3 and 6 | typ 15 · max 40 ns | 3 |
| Driver enable to output high | CL = 100pF, See Figures 4 and 6, S2 closed | typ 40 · max 70 ns | 3 |
| Driver enable to output low | CL = 100pF, See Figures 4 and 6, S1 closed | typ 40 · max 70 ns | 3 |
| Driver disable time from high | CL = 100pF, See Figures 4 and 6, S2 closed | typ 40 · max 70 ns | 3 |
| Driver disable time from low | CL = 100pF, See Figures 4 and 6, S1 closed | typ 40 · max 70 ns | 3 |
| Differential input threshold | -7V ≤ VCM ≤ 12V | min -0.2 · max 0.2 Volts | 3 |
| Input hysteresis | VCM = 0V | typ 20 mV | 3 |
| Output voltage high | VID = 200mV, IO = -4mA | min 3.5 Volts | 3 |
| Output voltage low | VID = 200mV, IO = 4mA | max 0.4 Volts | 3 |
| Three-state ( high impedance) output current | 0.4V ≤ VO ≤ 2.4V; RE = 5V; maximum magnitude ±1uA | max 1 uA | 3 |
| Input resistance | -7V ≤ VCM ≤ 12V | min 12 · typ 15 kΩ | 3 |
| Input current (A, B); VIN = 12V | DE = 0V, VCC = 0V or 5.25V, VIN = 12V | max 1 mA | 3 |
| Input current (A, B); VIN = -7V | DE = 0V, VCC = 0V or 5.25V, VIN = -7V | max -0.8 mA | 3 |
| Short circuit current | Receiver; 0V ≤ VO ≤ VCC | min 7 · max 95 mA | 3 |
| Maximum data rate | Receiver; RE = 0V, DE = 0V | min 10 Mbps | 3 |
| Receiver input to output tPLH | See Figures 3 & 7, RDIFF = 54Ω, CL1 = CL2 = 100pF | min 20 · typ 45 · max 100 ns | 3 |
| Differential receiver skew |tPHL - tPLH| | RDIFF = 54Ω, CL1 = CL2 = 100pF, See Figures 3 and 7 | typ 13 ns | 3 |
| Receiver enable to output low | CRL = 15pF, Figures 2 & 8; S1 Closed | typ 45 · max 70 ns | 3 |
| Receiver enable to output high | CRL = 15pF, Figures 2 & 8; S2 Closed | typ 45 · max 70 ns | 3 |
| Receiver Disable from low | CRL = 15pF, Figures 2 & 8; S1 Closed | typ 45 · max 70 ns | 3 |
| Receiver Disable from high | CRL = 15pF, Figures 2 & 8; S2 Closed | typ 45 · max 70 ns | 3 |
| Supply voltage VCC VCC | min 4.75 · max 5.25 Volts | 4 | |
| Supply current No load | RE, DI = 0V or VCC; DE = VCC | typ 900 uA | 4 |
| Supply current No load | RE = 0V, DI = 0V or 5V; DE = 0V | typ 600 uA | 4 |
| Operating Temperture | Industrial (_E_) | min -40 · max 85 °C | 4 |
| Storage Temperature | min -65 · max 150 °C | 4 |
Pins, by the datasheet
8- 1 RO
- Receiver output. · p. 4
- 2 RE
- Receiver output enable active LOW. · p. 4
- 3 DE
- Driver output enable active HIGH. · p. 4
- 4 DI
- Driver input. · p. 4
- 5 GND
- Ground connection. · p. 4
- 6 A
- Non-inverting driver output / receiver input. · p. 4
- 7 B
- Inverting driver output / receiver input. · p. 4
- 8 VCC
- Positive supply 4.75V ≤ Vcc ≤ 5.25V. · p. 4
Ordering codes, by the datasheet
1- SP485EEN-L/TR
- 8-pin NSOIC · Industrial operating temperature -40°C to 85°C; lead-free; reel packaging · p. 9
Open-source boards using it
5- 4 layers155 × 93 mm

- 4 layers33 × 46.4 mm

- 2 layers73 × 50 mm

- 2 layers

- 4 layers135 × 85 mm

Parts like it
8SP3485EN-L/TR
SOIC-8-40℃~+85℃ 1 1 10Mbps 2mA 3.3V 32 Half-Duplex Transceiver SOIC-8 RS-485 / RS-422 ICs ROHSMaxLinearRS-485 / RS-422 ICsSN75176BD
SOIC-80℃~+70℃ 1 1 4.75V~5.25V Transceiver SOIC-8 RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsMAX485ESA+T
SOIC-8-40℃~+85℃ 1 1 2.5Mbps 4.75V~5.25V Transceiver SOIC-8 RS-485 / RS-422 ICs ROHSMaxim Integrated (Analog Devices)RS-485 / RS-422 ICsMAX13487EESA+T
SOIC-8-40℃~+85℃ 1 1 128 4.5mA 4.75V~5.25V 500Kbps Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHSMaxim Integrated (Analog Devices)RS-485 / RS-422 ICsTHVD2450D
SOIC-8-40℃~+125℃ 1 1 256 3V~5.5V 50Mbps Half-Duplex Transceiver ±16kV SOIC-8 RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsTP8485E-SR
SOIC-8-40℃~+125℃ 1 1 1.4mA 250Kbps 256 3V~5.5V Transceiver ±18kV SOIC-8 RS-485 / RS-422 ICs ROHS3PEAKRS-485 / RS-422 ICsSP3078EEN-L/TR
SOIC-8-40℃~+85℃ 1 1 1.5mA 16Mbps 256 3.3V Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHSMaxLinearRS-485 / RS-422 ICsBL3085B
SOIC-8SOP-8L RS-485 / RS-422 ICs ROHSBLRS-485 / RS-422 ICs
Questions
Is there a KiCad symbol and footprint for the SP485EEN-L/TR?
Yes. The symbol is JLCPCB-Interface:Transceiver, RS485/422, 10Mbps, SP485EEN-L/TR and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the SP485EEN-L/TR?
SOIC-8, with 8 pins. Its footprint is drawn on this page.
Where is the SP485EEN-L/TR datasheet?
MaxLinear publishes it: the Datasheet link on this page opens it.
Where can I order the SP485EEN-L/TR?
JLCPCB lists it as part C6855, with 304,404 in stock; the sellers' links on this page open their listings.
What can replace the SP485EEN-L/TR?
Parts like it in the library: the SP3485EN-L/TR by MaxLinear, the SN75176BD by Texas Instruments, the MAX485ESA+T by Maxim Integrated (Analog Devices) and the MAX13487EESA+T by Maxim Integrated (Analog Devices). Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the SP485EEN-L/TR?
5 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.