

Castor and Pollux
A Juno-inspired dual oscillator
- Size
- 70.8 × 108 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 235
- Nets
- 150
- Pads
- 621
- Tracks, vias
- 992, 358
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 21 Jul 2020
- Updated
- 22 Sep 2025
Overview
Castor and Pollux is an open-source printed circuit board by wntrblm, from the wntrblm/Castor_and_Pollux repository on GitHub. It is a 4-layer board of 70.8 × 108 mm with 235 parts on 150 nets, routed with 992 tracks and 358 vias.
It is built around the ATSAMD21G18A-AU, TL074CPW and MCP4728-E/UN, with the MCP6004-E/P, SK9822 and 74LVC2G74DP,125-JSM among its other parts. Its parts include 69 resistors, 51 capacitors, 15 diodes, 14 ICs and 11 connectors. It belongs with the audio and music boards and the SAM D and SAM boards of this library.
Main components
12ATSAMD21G18A-AU
TQFP-48-40℃~+85℃ 1.62V~3.6V 10bit 12bit 256KB 32 Bit 32KB 38 48MHz ARM Cortex-M0+ Built-in FLASH 上电复位(POR)、欠压检测(BOR/LVD/LVR/LVI)、看门狗复位、内置通用定时器、硬件CRC、日历功能、触控功能 TQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)TL074CPW
TSSOP-14-15V~-5V、5V~15V 0℃~+70℃ 1.4mA 100pA 13V/us 18nV/√Hz@1kHz 18uV/℃ 3MHz 3mV 65pA 80dB Four channels Short-Circuit Protection、Built-in compensation、Latch-up suppression TSSOP-14 FET Input Amplifiers ROHSTexas InstrumentsFET Input AmplifiersMCP4728-E/UN
MSOP-10-40℃~+125℃ 12 2.7V~5.5V 2LSB 4 40nA 6us I2C Integrated buffer、Power-on reset、Power-down mode、Programmable gain Voltage Buffer MSOP-10 Digital to Analog Converters (DAC) ROHSMicrochip TechnologyDigital To Analog Converters (DAC)MCP6004-E/P
PDIP-14-40℃~+125℃ 1.8V~6V 100uA 1MHz 1pA 1pA 23mA 28nV/√Hz@1kHz 2uV/℃ 4 4.5mV 600V/ms 76dB ESD protection Rail-to-Rail Input, Rail-to-Rail Output PDIP-14 Operational Amplifier ROHSMicrochip TechnologyOperational AmplifierSK9822
SMD-6P,5.5x5mm-20℃~+80℃ 2 20mA 30MHz 4.5V~5.5V Built-in PWM SMD-6P,5.5x5mm LED Drivers ROHSOPSCO OptoelectronicsLED Drivers74LVC2G74DP,125-JSM
TSSOP-8-55℃~+125℃ 1 20MHz 32mA 32mA 3ns 3ns 4.5V~5.5V 4pF 4uA 74LVC 8 Asynchronous D-Type Reset、Enable Rising Edge Tri-State TSSOP-8 Flip Flops ROHSJSMSEMIFlip FlopsLD1117-3.3
SOT-223-40℃~+125℃@(Tj) 0.003%Vout 1 1.3V@(1A) 10mA 18V 1A 3.3V 60dB@(120Hz) Fixed Over Current Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSUMWVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLM4040DIM3-10.0/NOPB
SOT-23-40℃~+85℃@(Ta) 10V 110uA 150ppm/℃ 15mA 35uVrms Fixed Parallel ±1% SOT-23 Voltage Reference ROHSTexas InstrumentsVoltage ReferenceUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)RR0510P-103-D
0402-55℃~+125℃ 10kΩ 25V 62.5mW Thin Film Resistor ±0.5% ±25ppm/℃ 0402 Chip Resistor - Surface Mount ROHSSusumuChip Resistor - Surface MountCL21A226MAYNNNE
080522uF 25V X5R ±20% 0805 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSSamsung Electro-MechanicsMultilayer Ceramic Capacitors MLCC - SMD/SMTB72500T0250K060
060325V 300mJ 30A 31V 39V 3mW 67V 90pF@1MHz 0603 Varistors ROHSTDKVaristors
README
README.mdWinterbloom Castor & Pollux
Castor & Pollux is a Roland Juno-inspired oscillator in Eurorack format.
More details available at https://winterbloom.com/store/winterbloom-castor-and-pollux
Repository layout
This repository contains the hardware design files, firmware files, factory setup scripts, and user guide for Castor & Pollux.
- factory/ contains the scripts used to program, test, and calibrate the module after assembly. These scripts are all written in Python.
- firmware/ contains the firmware source code, build scripts, and third-party dependencies. The firmware is written in C using GCC ARM.
- hardware/ contains the hardware design files for the mainboard, jackboard, panel, and programming board. These are all created using KiCAD.
- user_guide/ contains the user's guide source files. These are written in Markdown and published using MkDocs.
License and contributing
Castor & Pollux is open-source hardware and software, however, licensing a project like this is a little complicated. Please take a chance to review the LICENSE file.
We welcome contributions! Please read our Contributing Guide and Code of Conduct.
Parts
235| Qty | Value | Footprint | References |
|---|---|---|---|
| 37 | Graphics | , , , , , , , , , , , , , , , +21 | |
| 25 | 100k | winterbloom:R_0402_HandSolder | R4, R6, R10, R22, R23, R24, R34, R35, R36, R37, R45, R46, R47, R57, R58, R59 +9 |
| 17 | 100n | winterbloom:C_0402_HandSolder | C5, C6, C8, C10, C11, C13, C14, C20, C40, C41, C42, C43, C46, C47, C48, C49 +1 |
| 10 | 10k | winterbloom:R_0402_HandSolder | R16, R21, R25, R26, R27, R39, R44, R48, R49, R50 |
| 10 | 18p | winterbloom:C_0402_HandSolder | C27, C28, C29, C30, C36, C37, C38, C39, C44, C45 |
| 9 | 1k | winterbloom:R_0603_HandSolder | R31, R32, R33, R38, R54, R55, R56, R61, R69 |
| 8 | 10u | winterbloom:C_0603_HandSolder | C4, C15, C24, C25, C26, C33, C34, C35 |
| 8 | 33k | winterbloom:R_0402_HandSolder | R20, R28, R29, R30, R43, R51, R52, R53 |
| 8 | Dotstar | winterbloom:LED_APA102_Dotstar_5050 | D7, D8, D9, D10, D11, D12, D13, D14 |
| 5 | 22u | winterbloom:C_0805_HandSolder | C1, C2, C3, C50, C51 |
| 4 | 2n2 | winterbloom:C_0402_HandSolder | C16, C17, C18, C19 |
| 4 | ESD | winterbloom:C_0603_HandSolder | D3, D4, D5, D6 |
| 4 | TL074 | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U7, U8, U11, U12 |
| 3 | 1u | winterbloom:C_0402_HandSolder | C7, C12, C21 |
| 3 | 2k2 | winterbloom:R_0402_HandSolder | R1, R2, R3 |
| 3 | 30V | winterbloom:D_SOD-123 | D1, D2, D15 |
| 3 | 600R@100MHz | winterbloom:L_0603_HandSolder | FB1, FB2, FB3 |
| 2 | 162k | winterbloom:R_0402_HandSolder | R5, R7 |
| 2 | 196k | winterbloom:R_0402_HandSolder | R9, R11 |
| 2 | 1k | winterbloom:R_0402_HandSolder | R18, R41 |
| 2 | 1n | winterbloom:C_0402_HandSolder | C23, C32 |
| 2 | 200k | winterbloom:R_0402_HandSolder | R17, R40 |
| 2 | 270R | winterbloom:R_0402_HandSolder | R19, R42 |
| 2 | 270p | winterbloom:C_0402_HandSolder | C22, C31 |
| 2 | 48k7 | winterbloom:R_0402_HandSolder | R12, R13 |
| 2 | 61k9 | winterbloom:R_0402_HandSolder | R14, R15 |
| 2 | 74LVC2G74 | Package_SO:TSSOP-8_3x3mm_P0.65mm | U9, U13 |
| 2 | LOGO | LOGO | G***, G*** |
| 2 | MCP6001-OT | Package_TO_SOT_SMD:SOT-23-5 | U10, U14 |
| 2 | MMBT3906 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | OSC OUT | winterbloom:AudioJack_WQP518MA | J7, J8 |
| 2 | Pulse level | winterbloom:Potentiometer_Alpha_R0904N | RV7, RV10 |
| 2 | Ramp | TestPoint:TestPoint_Pad_D1.0mm | TP11, TP12 |
| 2 | Ramp level | winterbloom:Potentiometer_Alpha_R0904N | RV6, RV9 |
| 2 | Sub level | winterbloom:Potentiometer_Alpha_R0904N | RV8, RV11 |
| 1 | -10V | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | ATSAMD21G18A-A | winterbloom:TQFP-48_7x7mm_P0.5mm | U3 |
| 1 | BUTTON | winterbloom:Tactile_Switch_6mm | SW2 |
| 1 | CASTOR DUTY | winterbloom:AudioJack_WQP518MA | J5 |
| 1 | CASTOR PITCH | winterbloom:AudioJack_WQP518MA | J3 |
| 1 | Castor duty | winterbloom:Potentiometer_Alpha_R0904N | RV4 |
| 1 | Castor pitch | winterbloom:Potentiometer_Alpha_R0904N | RV1 |
| 1 | Crossfade | winterbloom:Potentiometer_Alpha_R0904N | RV12 |
| 1 | D+ | TestPoint:TestPoint_Pad_D1.0mm | TP9 |
| 1 | D- | TestPoint:TestPoint_Pad_D1.0mm | TP10 |
| 1 | EXT | winterbloom:Connector_Cortex_Debug_IDC_2x05_P1.27mm_Vertical_Shrouded_SMD | J9 |
| 1 | Eurorack Power | winterbloom:Eurorack_Power_2x5_Shrouded | J1 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | LD1117-3.3 | Package_TO_SOT_SMD:TO-252-3_TabPin2 | U1 |
| 1 | LFO | winterbloom:Potentiometer_Alpha_R0904N | RV3 |
| 1 | LM4040DBZ-10 | Package_TO_SOT_SMD:SOT-23 | U2 |
| 1 | LOGO | winterbloom:Symbol_Winterbloom_40mm | G*** |
| 1 | LOGO | mainboard:castor_and_pollux | G*** |
| 1 | LOGO | winterbloom:ce_5mm | G*** |
| 1 | MCP4728 | Package_SO:MSOP-10_3x3mm_P0.5mm | U5 |
| 1 | MCP6004 | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U6 |
| 1 | MIX | winterbloom:AudioJack_WQP518MA | J10 |
| 1 | POLLUX DUTY | winterbloom:AudioJack_WQP518MA | J6 |
| 1 | POLLUX PITCH | winterbloom:AudioJack_WQP518MA | J4 |
| 1 | Pollux duty | winterbloom:Potentiometer_Alpha_R0904N | RV5 |
| 1 | Pollux pitch | winterbloom:Potentiometer_Alpha_R0904N | RV2 |
| 1 | RESET | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | RESET | winterbloom:Tactile_Switch_4.2mm | SW1 |
| 1 | SQ1 | TestPoint:TestPoint_Pad_D1.0mm | TP8 |
| 1 | SQ2 | TestPoint:TestPoint_Pad_D1.0mm | TP7 |
| 1 | SWCLK | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | SWDIO | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | USB | winterbloom:USB_B_Micro_Receptacle | J2 |
| 1 | USB ALT | winterbloom:SolderWirePad_1x04_SMD_2x5mm | J11 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
The 233 most common of 235 parts.
More from wntrblm/Castor_and_Pollux
3- 2 layers100 × 120 mm

- 2 layers9.8 × 108 mm

- 2 layers9.6 × 4.5 mm

Similar boards
- 4 layers30 × 53.5 mm

Speak to Me
wntrblm/Speak_to_Me
A beautiful stereo headphone amplifier and a delightfully lo-fi speaker
54 parts20 - 4 layers83 × 55 mm

- 2 layers39 × 50 mm

CANInstallHub
charlesrwest/CANInstallHub
A temporary home for the PCB design files for the CANInstallPrototype
53 parts - 6 layers160 × 100 mm

Timing Control V1p1
sOrzada/STASIS_Exposure_Hardware
This is the repository for the exposition hardware of the STASIS project.
103 partsCERN-OHL-W-2.0 - 4 layers45 × 33.5 mm

- 2 layers120 × 102.5 mm

Dsug cctv BOARD
LucasLHenry/spelltwister
This is the third version of the code for the Spelltwister module with CCTV. This version uses the Arduino platform and the RP2040, a chip developed by Raspberry Pi for their RPi Pico board.
251 partsMIT - 2 layers

Andes 12hp
niektb/sluisbrinkie-eurorack-published
Published Modules of the Sluisbrinkie project
141 parts34 - 2 layers53.6 × 53.3 mm

Questions
How big is the Castor and Pollux PCB?
It measures 70.8 × 108 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Castor and Pollux use?
235 parts, built around the ATSAMD21G18A-AU, TL074CPW, MCP4728-E/UN and MCP6004-E/P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Castor and Pollux KiCad files?
From the wntrblm/Castor_and_Pollux repository on GitHub, at the commit this page was made from: the board is hardware/mainboard/mainboard.kicad_pcb and its schematic hardware/expander/expander.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Castor and Pollux design in my own project?
Its repository states no licence, so its author keeps all rights: ask wntrblm before reusing the design.