

Dsug cctv BOARD
This is the third version of the code for the Spelltwister module with CCTV. This version uses the Arduino platform and the RP2040, a chip developed by Raspberry Pi for their RPi Pico board.
- Size
- 120 × 102.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 251
- Nets
- 187
- Pads
- 840
- Tracks, vias
- 2,325, 153
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 15 May 2024
- Updated
- 27 Feb 2025
Overview
Dsug cctv BOARD is an open-source printed circuit board by LucasLHenry, from the LucasLHenry/spelltwister repository on GitHub, published under the MIT licence. It is a 2-layer board of 120 × 102.5 mm with 251 parts on 187 nets, routed with 2,325 tracks and 153 vias.
It is built around the RP2040, 74AHCT1G125SE and MCP6004-E/P, with the AP63205WU, W25Q128JVSIQ and AMS1117-3.3 among its other parts. Its parts include 101 resistors, 66 capacitors, 25 diodes, 20 connectors and 16 ICs. It belongs with the RP2040 boards of this library.
Main components
12RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)74AHCT1G125SE
SOT-353-40℃~+125℃ 1 1 4.5V~5.5V 4.7ns@5V,50pF 40uA 74AHCT 8mA 8mA Schmitt trigger Tri-State Unidirectional SOT-353 Buffers, Drivers, Receivers, Transceivers ROHSDiodes IncorporatedBuffers, Drivers, Receivers, TransceiversMCP6004-E/P
PDIP-14-40℃~+125℃ 1.8V~6V 100uA 1MHz 1pA 1pA 23mA 28nV/√Hz@1kHz 2uV/℃ 4 4.5mV 600V/ms 76dB ESD protection Rail-to-Rail Input, Rail-to-Rail Output PDIP-14 Operational Amplifier ROHSMicrochip TechnologyOperational AmplifierAP63205WU
TSOT-23-6-40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.8V~32V 5V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHSDiodes IncorporatedDC-DC ConvertersW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsCD4051BE
PDIP-16-55℃~+125℃ 125Ω 20MHz 3V~20V 450ns 8 8:1 PDIP-16 Analog Switches, Multiplexers ROHSTexas InstrumentsAnalog Switches, MultiplexersLM4040DIM3-10.0/NOPB
SOT-23-40℃~+85℃@(Ta) 10V 110uA 150ppm/℃ 15mA 35uVrms Fixed Parallel ±1% SOT-23 Voltage Reference ROHSTexas InstrumentsVoltage ReferenceSK6812MINI-E
SMD-40℃~+85℃ 0.6mA 1.78mm 120mcd~240mcd 120° 160mcd~320mcd 1kHz 2.8mm 2000V 3.2mm 3.7V~5.5V 460nm~470nm 515nm~525nm 620nm~625nm 800Kbit/s 815mcd~1275mcd Semi-transparent lens SMD RGB LEDs(Built-in IC) ROHSOPSCO OptoelectronicsRGB LEDs(Built-In IC)MMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)TS-1187A-B-A-B
SMD-4P,5.1x5.1mm-30℃~+85℃ 1.5mm 1.6N 100,000 cycles 12V 5.1mm 5.1mm 50mA Gold No Round Button SPST Surface Mount,Vertical Without Bracket SMD-4P,5.1x5.1mm Tactile Switches ROHSXKB ConnectionTactile SwitchesTYPEC-304-ACP16
SMD-40℃~+85℃ 1 10000 times 16P 20V 3A 7.35mm Black Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSXUNPUUSB Connectors
README
README.mdspelltwister
Spelltwister is a dual function generator with a large palette of modulation algorithms. It has three modes: ENV (slow, single-cycle), LFO (slow, free-running), and VCO (fast, free-running). Each side of the module is a waveformer, which generates a signal controlled by three knobs. The basic structure of this signal is that of an AD envelope, so the signal first rises to it's maximum value (in a variable time and curvature), then falls back to it's minimum value (in a variable time and curvature).
The three knobs are Time, Shape, and Ratio. Time controls the overall time for one cycle of the waveform, so also functions as pitch in VCO mode. Ratio controls the ratio between the time spent on the first stage versus the second stage (so ratio set fully CCW would mean that all time is spent falling, which would form a downwards saw wave). Lastly, Shape controls the curvature of the rising and falling, from exponential to logarithmic. With Shape in it's center position, the slope is linear, but turning it below 12 o'clock makes the rising and falling more exponential, while turning it the other way makes it more logarithmic.
Parts
251| Qty | Value | Footprint | References |
|---|---|---|---|
| 32 | 100nF | Capacitor_SMD:C_0603_1608Metric | C3, C4, C12, C13, C14, C15, C16, C17, C19, C24, C25, C26, C27, C37, C38, C39 +16 |
| 31 | 10k | Resistor_SMD:R_0603_1608Metric | R2, R12, R13, R16, R17, R24, R25, R26, R31, R32, R40, R41, R42, R43, R45, R46 +15 |
| 23 | SK6812MINI-E | benjiaomodular:SK6812MINIE | D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24, D25 +7 |
| 18 | JACK | benjiaomodular:AudioJack_3.5mm_with_drawing | J2, J4, J5, J6, J7, J10, J11, J12, J13, J14, J15, J16, J17, J18, J19, J20 +2 |
| 14 | 100k | Resistor_SMD:R_0603_1608Metric | R6, R14, R15, R19, R21, R28, R34, R35, R59, R61, R63, R72, R74, R96 |
| 14 | 1nF | Capacitor_SMD:C_0603_1608Metric | C9, C18, C20, C21, C28, C29, C30, C32, C34, C36, C41, C49, C51, C53 |
| 10 | 120k | Resistor_SMD:R_0603_1608Metric | R5, R18, R20, R27, R36, R60, R62, R64, R73, R95 |
| 10 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R8, R9, R44, R54, R55, R79, R92, R93, R98 |
| 8 | 10k | benjiaomodular:Potentiometer_RV09_talltrimmer | RV1, RV2, RV3, RV6, RV7, RV8, RV10, RV14 |
| 8 | 22k | Resistor_SMD:R_0603_1608Metric | R7, R22, R23, R29, R68, R69, R76, R97 |
| 6 | 10k | benjiaomodular:Potentiometer_RV09_6mm_knob | RV4, RV5, RV9, RV11, RV12, RV13 |
| 6 | 2.2nF | Capacitor_SMD:C_0603_1608Metric | C31, C33, C35, C48, C50, C52 |
| 6 | 22uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C1, C2, C7, C55, C56, C57 |
| 4 | 180k | Resistor_SMD:R_0603_1608Metric | R33, R38, R58, R66 |
| 4 | 1uF | Capacitor_SMD:C_0603_1608Metric | C45, C47, C60, C62 |
| 4 | 39k | Resistor_SMD:R_0603_1608Metric | R51, R52, R89, R90 |
| 4 | 4.7k | Resistor_SMD:R_0603_1608Metric | R84, R85, R102, R103 |
| 4 | 56k | Resistor_SMD:R_0603_1608Metric | R48, R82, R83, R101 |
| 4 | TL074 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U5, U9, U12, U14 |
| 3 | MCP6004 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U7, U10, U11 |
| 2 | 10nF | Capacitor_SMD:C_0603_1608Metric | C22, C23 |
| 2 | 15pF | Capacitor_SMD:C_0603_1608Metric | C10, C11 |
| 2 | 1M | Resistor_SMD:R_0603_1608Metric | R3, R30 |
| 2 | 1N4148 | Diode_SMD:D_SOD-123 | D1, D2 |
| 2 | 270k | Resistor_SMD:R_0603_1608Metric | R37, R65 |
| 2 | 27R | Resistor_SMD:R_0603_1608Metric | R104, R105 |
| 2 | 470k | Resistor_SMD:R_0603_1608Metric | R4, R53 |
| 2 | 47k | Resistor_SMD:R_0603_1608Metric | R39, R67 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric | R10, R11 |
| 2 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1, U3 |
| 2 | CD4051B | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U4, U6 |
| 2 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q3, Q4 |
| 2 | SW_SPDT_MSM | benjiaomodular:SPDT_P2.54mm_Vertical | SW4, SW5 |
| 1 | 24_detent | benjiaomodular:RotaryEncoder_Switch_Vertical_H20mm_20mm_knob | SW2 |
| 1 | 4.7uH | User_Footprints:L_TaiTech_HPC3010TF-4R7M | L1 |
| 1 | 74AHCT1G125 | Package_TO_SOT_SMD:SOT-353_SC-70-5 | U16 |
| 1 | AP63205WU | Package_TO_SOT_SMD:TSOT-23-6 | U15 |
| 1 | Conn_02x05_Top_Bottom | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J1 |
| 1 | Crystal_GND24 | benjiaomodular:ABM8-272-T3_ABR | Y1 |
| 1 | LM4040DIM3-10.0/NOPB | Package_TO_SOT_SMD:SOT-23 | U8 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U13 |
| 1 | SW_Push | benjiaomodular:SW_PUSH_6mm | SW3 |
| 1 | TS-1187A-B-A-B | benjiaomodular:push_switch_5.1x5.1 | SW1 |
| 1 | TYPEC-304-ACP16 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U2 |
Similar boards
- 4 layers70.8 × 108 mm

- 4 layers99 × 79 mm

- 4 layers45 × 33.5 mm

- 4 layers138 × 114 mm

Glitchwave567
jdg511/567Terror
Software simulation of the Glitchwave 567 (LM567 glitch pedal) — JUCE Standalone + VST3
299 partsMIT - 2 layers50 × 110 mm

Ogham merged v1.0
keeos-io/ogham
Ogham — a dual-voice bytebeat synthesizer for Eurorack. Firmware (MIT) and hardware (CC BY-SA 4.0).
109 parts3 - 2 layers66 × 107.5 mm

Tonwerk haupt
Marcel-B/Synth
Die beiden Browser-Synthesizer aus Tonwerk (YuE UI) als Plugins für Logic Pro: Tonwerk Analog und Tonwerk FM, jeder mit Delay und Hall und eigenen Werksklängen.
100 parts - 2 layers68.6 × 101.6 mm

- 4 layers47 × 90 mm

PicoLume v4
picolume/hardware
Hardware designs for the PicoLume wireless LED prop system. All designs are created in KiCad.
102 partsMIT
Questions
How big is the Dsug cctv BOARD PCB?
It measures 120 × 102.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Dsug cctv BOARD use?
251 parts, built around the RP2040, 74AHCT1G125SE, MCP6004-E/P and AP63205WU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Dsug cctv BOARD KiCad files?
From the LucasLHenry/spelltwister repository on GitHub, at the commit this page was made from: the board is hardware design/dsug_cctv_BOARD.kicad_pcb and its schematic hardware design/LEDs.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Dsug cctv BOARD design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).