Skip to the content
123456

AP63205WU

Diodes IncorporatedExtended

-40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.8V~32V 5V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHS

Part id
diodes/AP63205WU
Category
DC DC Converters
Package
TSOT-23-6
Pins
6
In stock
20,592 at JLCPCB (C2071056)
Used on
224 open-source boards

Overview

The AP63205WU is a DC DC Converter made by Diodes Incorporated in a TSOT-23-6 package with 6 pins. -40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.8V~32V 5V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Regulator_Switching:AP63205WU, from KiCad's library) and its footprint (Package_TO_SOT_SMD:TSOT-23-6, from KiCad's library), ready for a KiCad board. 20,592 are in stock at JLCPCB (part C2071056). 224 open-source boards in 163 repositories on GitHub use it.

Symbol

1FB2EN3IN4GND5SW6BST
Regulator_Switching:AP63205WUFrom KiCad's library

Footprint

123456
Package_TO_SOT_SMD:TSOT-23-6From KiCad's library

From the datasheet

15
Supply, least
3.8 V · VIN, recommended operating min · p. 4
Supply, most
32 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
35 V · VIN, absolute max DC · p. 4
Supply, absolute maximum
40 V · VIN, absolute max for 400ms · p. 4
Works from
-40 °C · Operating ambient min · p. 4
Works up to
85 °C · Operating ambient max · p. 4
Junction, hottest
160 °C · Junction temperature absolute max · p. 4
Takes working
22 µA · VIN quiescent current typical, no load, non-switching · p. 10
Takes asleep
1 µA · Shutdown supply current typical, VEN = 0V · p. 5
Gives
2 A · Continuous output current max · p. 1
Current limit
2.8 A · HS peak current limit typical · p. 5
Output
5 V · AP63205 fixed output voltage typical, CCM · p. 5
Switches at
1.1 MHz · Oscillator frequency typical · p. 5
Junction to air (TSOT26)
89 K/W · Junction to ambient · p. 4
Junction to case (TSOT26)
39 K/W · Junction to case · p. 4

What it is and has

9
Continuous output current
2A · p. 1
Fixed output voltage
5.0V · p. 1
Switching frequency
1.1MHz · p. 1
Package
TSOT26 · p. 1
EMI reduction
Frequency Spread Spectrum · p. 1
Protection
Overvoltage Protection · p. 1
Protection
Cycle-by-Cycle Peak Current Limit · p. 1
Protection
Thermal Shutdown · p. 1
Compliance
Totally Lead-Free & Fully RoHS Compliant · p. 1

Around it

5
ind 4.7 µH
between SW and VOUT; AP63205 recommended component selection for 5V output; Figure 21. · p. 13
cap 10 µF
between VIN and GND; C1, AP63205 recommended component selection; Figure 21. · p. 13
cap 2 x 22 µF
between VOUT and GND; C2, AP63205 recommended component selection; Figure 21. · p. 13
cap 100nF
between BST and SW; Ceramic bootstrap capacitor required for proper operation. · p. 14
cap 22µF to 68µF
between VOUT and GND; General output capacitor recommendation: ceramic, large capacitance and low ESR. · p. 14

Specifications

33
ParameterConditionsAs printedPage
Supply Voltage VINTA = +25°C; DCmin -0.3 · max 35 V4
Supply Voltage VINTA = +25°C; 400msmin -0.3 · max 40 V4
Switch Node Voltage VSWTA = +25°C; maximum VIN + 0.3 Vmin -1 V4
Feedback Voltage VFBTA = +25°Cmin -0.3 · max 6 V4
Enable/UVLO Voltage VENTA = +25°Cmin -0.3 · max 35 V4
Storage Temperature TSTmin -65 · max 150 °C4
Junction Temperature TJmax 160 °C4
Lead Temperature TLmax 260 °C4
Human Body Mode HBMmax 2000 V4
Charge Device Model CDMmax 1000 V4
Junction to Ambient θJATSOT26; FR-4 substrate, single-layer PC board, 2oz copper, minimum recommended pad layouttyp 89 °C/W4
Junction to Case θJCTSOT26; FR-4 substrate, single-layer PC board, 2oz copper, minimum recommended pad layouttyp 39 °C/W4
Supply Voltage VINTA = +25°Cmin 3.8 · max 32 V4
Operating Ambient Temperature Range TAmin -40 · max 85 °C4
Shutdown Supply Current ISHDNTA = +25°C, VIN = 12V; VEN = 0Vtyp 1 · max 3 uA5
Supply Current (Quiescent) IQAP63205; TA = +25°C, VIN = 12V; VEN = OPEN, VFB = 1.0Vtyp 22 uA5
VIN Under Voltage Threshold (Rising) UVLOTA = +25°C, VIN = 12V unless otherwise specifiedmin 3.3 · typ 3.5 · max 3.7 V5
VIN Under Voltage Threshold Hysteresis UVLOTA = +25°C, VIN = 12V unless otherwise specifiedtyp 440 mV5
High-Side Switch On-Resistance (Note 8) RDS(ON)1TA = +25°C, VIN = 12Vtyp 125 mΩ5
Low-Side Switch On-Resistance (Note 8) RDS(ON)2TA = +25°C, VIN = 12Vtyp 68 mΩ5
HS Peak Current Limit (Note 8) IPEAK_LIMITTA = +25°C, VIN = 12Vmin 2.5 · typ 2.8 · max 3.1 A5
LS Valley Current Limit (Note 8) IVALLEY_LIMITTA = +25°C, VIN = 12Vmin 2.5 · typ 3.2 · max 3.9 A5
Oscillator Frequency fSWAP63205; TA = +25°C, VIN = 12Vtyp 1100 kHz5
Frequency Spread Spectrum FSSTA = +25°C, VIN = 12V; typical ±6%typ 6 %5
Minimum On Time tONTA = +25°C, VIN = 12Vtyp 80 ns5
Feedback Voltage VFBCCM, AP63205; TA = +25°C, VIN = 12Vmin 4.95 · typ 5 · max 5.05 V5
EN Logic High VEN_HTA = +25°C, VIN = 12Vmin 1.15 · typ 1.18 · max 1.23 V5
EN Logic Low VEN_LTA = +25°C, VIN = 12Vmin 1.05 · typ 1.1 · max 1.15 V5
EN Input Current IENTA = +25°C, VIN = 12V; VEN = 1.5Vtyp 5.5 uA5
EN Input Current IENTA = +25°C, VIN = 12V; VEN = 1Vtyp 1.5 uA5
Soft-Start Period tSSTA = +25°C, VIN = 12Vtyp 4 ms5
Thermal Shutdown (Note 8) TSDVIN = 12Vtyp 160 °C5
Thermal Hysteresis (Note 8) THYSVIN = 12Vtyp 25 °C5

Pins, by the datasheet

6
1 FB
Feedback sensing terminal for the output voltage; the pin table directs connection to the output resistive divider. · p. 2
2 EN
Enable input: high turns the regulator on, low turns it off; attach to VIN or leave open for automatic startup; precision threshold supports programming UVLO. · p. 2
3 VIN
Power input for the IC and converter switches; drive with 3.8V to 32V and bypass to GND with a suitably large capacitor. · p. 2
4 GND
Power Ground. · p. 2
5 SW
Power switching output; connect the output LC filter to the load and a capacitor from SW to BST. · p. 2
6 BST
High-side gate drive boost input; connect a recommended 100nF capacitor from SW to BST. · p. 2

Open-source boards using it

224See all 224
  • 2 layers28.3 × 14.3 mmTap Photosensor PCB, the printed circuit board in 3D

    Tap Photosensor PCB

    VoronDesign/Voron-Tap

    Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

    18 parts716GPL-3.0
  • 6 layers84 × 98 mmFujiNet-5200-Rev0, the printed circuit board in 3D

    FujiNet-5200-Rev0

    FujiNetWIFI/fujinet-hardware

    Schematics and design files for FujiNet hardware

    145 parts142
  • 2 layers65 × 70 mmOpenradfan, the printed circuit board in 3D

    Openradfan

    andrekuehne/openradfan

    An ESPHome-driven controller for radiator fans to improve heat output

    49 parts29MIT
  • 4 layers96 × 172 mmServo cpu, the printed circuit board in 3D

    Servo cpu

    wiciu15/servo2

    Servo inverter for 3-phase AC motor with/out encoder feedback

    167 parts29
  • 4 layers355 × 160 mmLiBCM, the printed circuit board in 3D

    LiBCM

    doppelhub/Honda_Insight_LiBCM

    Replacement BCM for G1 Honda Insight Lithium Conversion

    717 parts25CC-BY-SA-4.0
  • 2 layers82.5 × 140 mmQCamPCR, the printed circuit board in 3D

    QCamPCR

    GaudiLabs/qPocketPCR

    Quantitative PCR machine detecting fluorescence using a camera

    113 parts22GPL-3.0
  • 2 layers28.8 × 14.3 mmTap Photosensor PCB, the printed circuit board in 3D

    Tap Photosensor PCB

    Qballjos/Voron-2.4-Otopus-pro-SB2209-U2C-CAN

    Voron 2.4 R2 with ,Stealthburner, Voron Tap, Bambu lab Hotend. Octopus pro with TMC2209 UART, EBB SB2209 v1.0 and U2C v2.1 running klipper

    12 parts21
  • 2 layers130 × 53 mmTougherPowerMeter FeatherWing, the printed circuit board in 3D

    TougherPowerMeter FeatherWing

    ahillbom/TougherPowerMonitor-HW

    Triple-channel power monitor based on INA3221 and TPS1HB08A with some filtering for tougher conditions. Compatible with Arduino Nano and Feathers.

    85 parts19MIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the AP63205WU?

Yes. The symbol is Regulator_Switching:AP63205WU and the footprint Package_TO_SOT_SMD:TSOT-23-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the AP63205WU?

TSOT-23-6, with 6 pins. Its footprint is drawn on this page.

Where is the AP63205WU datasheet?

Diodes Incorporated publishes it: the Datasheet link on this page opens it.

Where can I order the AP63205WU?

JLCPCB lists it as part C2071056, with 20,592 in stock; the sellers' links on this page open their listings.

What can replace the AP63205WU?

Parts like it in the library: the SCT2325TVBR by SCT, the SD8942 by SHOUDING, the SGM6603-5.0YN6G/TR by SG Micro and the ISL9111AEH50Z-T by Renesas Electronics. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the AP63205WU?

224 boards in 163 repositories on GitHub; the most starred are listed on this page, with their KiCad files.