
ATSAMD21G18A-AU
Microchip TechnologyExtended
-40℃~+85℃ 1.62V~3.6V 10bit 12bit 256KB 32 Bit 32KB 38 48MHz ARM Cortex-M0+ Built-in FLASH 上电复位(POR)、欠压检测(BOR/LVD/LVR/LVI)、看门狗复位、内置通用定时器、硬件CRC、日历功能、触控功能 TQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHS
- Part id
- microchip/ATSAMD21G18A-AU
- Category
- Microcontrollers (MCU, MPU, SOC)
- Package
- TQFP-48
- Pins
- 48
- In stock
- 4,184 at JLCPCB (C78624)
- Used on
- 70 open-source boards
Overview
The ATSAMD21G18A-AU is a microcontroller made by Microchip Technology in a TQFP-48 package with 48 pins. -40℃~+85℃ 1.62V~3.6V 10bit 12bit 256KB 32 Bit 32KB 38 48MHz ARM Cortex-M0+ Built-in FLASH 上电复位(POR)、欠压检测(BOR/LVD/LVR/LVI)、看门狗复位、内置通用定时器、硬件CRC、日历功能、触控功能 TQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHS.
PCBKit's library has its KiCad symbol (MCU_Microchip_SAMD:ATSAMD21G18A-A, from KiCad's library) and its footprint (Package_QFP:TQFP-48_7x7mm_P0.5mm, from KiCad's library), ready for a KiCad board. 4,184 are in stock at JLCPCB (part C78624). 70 open-source boards in 58 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
11- Supply, least
- 1.62 V · VDD, recommended operating min, BOD33 disabled · p. 864
- Supply, most
- 3.63 V · VDD, recommended operating max · p. 864
- Supply, absolute maximum
- 3.8 V · VDD, absolute max · p. 864
- Works from
- -40 °C · TA, operating ambient min · p. 864
- Works up to
- 85 °C · TA, operating ambient max · p. 864
- Junction, hottest
- 100 °C · TJ, operating junction max · p. 864
- Takes working
- 6.32 mA · VDDIN, typical ACTIVE CoreMark, 48 MHz, 3.3 V, 25°C · p. 868
- Takes at most
- 7 mA · VDDIN, max ACTIVE CoreMark, 48 MHz, 3.3 V, 85°C · p. 868
- A pin gives at most
- 10 mA · IOL, max sink, VDD=3V-3.63V, DRVSTR=1 · p. 875
- Junction to air (48-pin TQFP)
- 63.6 K/W · junction-to-ambient · p. 863
- Junction to case (48-pin TQFP)
- 12.2 K/W · junction-to-case · p. 863
What it is and has
22- Processor
- Arm Cortex-M0+ CPU, up to 48 MHz · p. 1
- Hardware multiplier
- Single-cycle · p. 1
- Trace
- Micro Trace Buffer (MTB) · p. 1
- Reset protection
- Power-on Reset (POR) and Brown-out Detection (BOD) · p. 1
- External interrupts
- 16 · p. 1
- Non-maskable interrupt
- 1 · p. 1
- Debug interface
- Two-pin SWD programming, test and debugging · p. 1
- Sleep modes
- Idle and Standby · p. 1
- SleepWalking
- Peripheral support · p. 1
- DMA
- 12 channels · p. 1
- Event System
- 12 channels · p. 1
- RTC
- 32-bit with clock/calendar · p. 1
- Watchdog
- Watchdog Timer (WDT) · p. 1
- CRC
- CRC-32 generator · p. 1
- Processor
- Arm Cortex-M0+, up to 48 MHz · p. 1
- Reset and brown-out detection
- Power-on Reset (POR), Brown-out Detection (BOD) · p. 1
- Debug interface
- Two-pin Serial Wire Debug (SWD) · p. 1
- SleepWalking
- SleepWalking peripherals · p. 1
- DMA
- 12-channel Direct Memory Access Controller · p. 1
- CPU
- Arm Cortex-M0+, up to 48 MHz · p. 1
- Low-power peripherals
- SleepWalking · p. 1
- Event System
- 12-channel · p. 1
Around it
3- cap 10 µF
- between VDDIN and GND; Ceramic X7R with low series resistance. · p. 877
- cap 100 nF
- between VDDIN and GND; Input regulator decoupling; ceramic X7R with low series resistance. · p. 877
- cap 1 µF
- between VDDCORE and GND; Minimum 0.8 uF; ceramic or solid tantalum recommended; ESR <= 1 ohms. · p. 877
Specifications
232| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Junction-to-ambient thermal resistance θJA | 48-pin TQFP | typ 63.6 °C/W | 863 |
| Junction-to-case thermal resistance θJC | 48-pin TQFP | typ 12.2 °C/W | 863 |
| Power supply voltage VDD | min 0 · max 3.8 V | 864 | |
| Current into a VDD pin IVDD | Maximum source current is 46mA per cluster | max 92 mA | 864 |
| Current out of a GND pin IGND | Maximum sink current is 65mA per cluster | max 130 mA | 864 |
| Storage temperature Tstorage | min -60 · max 150 °C | 864 | |
| Power supply voltage VDD | With BOD33 disabled | min 1.62 · typ 3.3 · max 3.63 V | 864 |
| Analog supply voltage VDDANA | With BOD33 disabled | min 1.62 · typ 3.3 · max 3.63 V | 864 |
| Temperature range TA | min -40 · typ 25 · max 85 °C | 864 | |
| Junction temperature TJ | max 100 °C | 864 | |
| Full Voltage Range VDDIO, VDDIN, VDDANA | TA = -40°C to 85°C; TJ up to 100°C | min 1.62 · max 3.63 V | 865 |
| DC supply peripheral I/Os, internal regulator and analog supply voltage VDDIO, VDDIN, VDDANA | max 0.1 V/us | 865 | |
| GCLK Generator Output Frequency fGCLKGEN0 / fGCLK_MAIN, fGCLKGEN1, fGCLKGEN2, fGCLKGEN3, fGCLKGEN4, fGCLKGEN5, fGCLKGEN6, fGCLKGEN7, fGCLKGEN8 | Undivided | max 96 MHz | 865 |
| GCLK Generator Output Frequency fGCLKGEN0 / fGCLK_MAIN, fGCLKGEN1, fGCLKGEN2, fGCLKGEN3, fGCLKGEN4, fGCLKGEN5, fGCLKGEN6, fGCLKGEN7, fGCLKGEN8 | Divided | max 48 MHz | 865 |
| CPU clock frequency fCPU | max 48 MHz | 865 | |
| AHB clock frequency fAHB | max 48 MHz | 865 | |
| APBA clock frequency fAPBA | max 48 MHz | 865 | |
| APBB clock frequency fAPBB | max 48 MHz | 865 | |
| AC1 analog input clock frequency fGCLK_AC1_ANA | max 64 KHz | 867 | |
| DAC input clock frequency fGCLK_DAC | max 48 MHz | 867 | |
| PTC input clock frequency fGCLK_PTC | max 48 MHz | 867 | |
| I2S serializer 0 input clock frequency fGCLK_I2S_0 | max 13 MHz | 867 | |
| I2S serializer 1 input clock frequency fGCLK_I2S_1 | max 13 MHz | 867 | |
| ACTIVE | CPU running a While(1) algorithm; 25°C; default operating conditions | min 3.11 · typ 3.37 · max 3.64 mA | 868 |
| ACTIVE | CPU running a While(1) algorithm; 85°C; default operating conditions | min 3.24 · typ 3.48 · max 3.76 mA | 868 |
| ACTIVE | CPU running a While(1) algorithm; VDDIN=1.8V; Flash with 3 wait states; 25°C | min 3.1 · typ 3.36 · max 3.64 mA | 868 |
| ACTIVE | CPU running a While(1) algorithm; VDDIN=1.8V; Flash with 3 wait states; 85°C | min 3.24 · typ 3.48 · max 3.75 mA | 868 |
| ACTIVE | CPU running a Fibonacci algorithm; 25°C; default operating conditions | min 4.12 · typ 4.53 · max 4.92 mA | 868 |
| ACTIVE | CPU running a Fibonacci algorithm; 85°C; default operating conditions | min 4.27 · typ 4.63 · max 4.98 mA | 868 |
| ACTIVE | CPU running a Fibonacci algorithm; VDDIN=1.8V; Flash with 3 wait states; 25°C | min 4.12 · typ 4.53 · max 4.92 mA | 868 |
| ACTIVE | CPU running a Fibonacci algorithm; VDDIN=1.8V; Flash with 3 wait states; 85°C | min 4.27 · typ 4.63 · max 4.98 mA | 868 |
| ACTIVE | CPU running a CoreMark algorithm; 25°C; default operating conditions | min 5.78 · typ 6.32 · max 6.8 mA | 868 |
| ACTIVE | CPU running a CoreMark algorithm; 85°C; default operating conditions | min 5.93 · typ 6.47 · max 7 mA | 868 |
| ACTIVE | CPU running a CoreMark algorithm; VDDIN=1.8V; Flash with 3 wait states; 25°C | min 5.17 · typ 5.6 · max 5.96 mA | 868 |
| ACTIVE | CPU running a CoreMark algorithm; VDDIN=1.8V; Flash with 3 wait states; 85°C | min 5.35 · typ 5.73 · max 6.1 mA | 868 |
| IDLE0 | Default operating conditions; 25°C | min 1.89 · typ 2.04 · max 2.2 mA | 868 |
| IDLE0 | Default operating conditions; 85°C | min 1.98 · typ 2.14 · max 2.33 mA | 868 |
| IDLE1 | Default operating conditions; 25°C | min 1.34 · typ 1.46 · max 1.58 mA | 868 |
| IDLE1 | Default operating conditions; 85°C | min 1.41 · typ 1.55 · max 1.71 mA | 868 |
| IDLE2 | Default operating conditions; 25°C | min 1.07 · typ 1.17 · max 1.28 mA | 868 |
| IDLE2 | Default operating conditions; 85°C | min 1.13 · typ 1.27 · max 1.4 mA | 868 |
| Wait connection | GCLK_USB is off, using USB wakeup asynchronous interrupt. USB bus not connected. | typ 0.1 uA | 874 |
| Wait connection | GCLK_USB is on. USB bus not connected. | typ 0.19 mA | 874 |
| Suspend | GCLK_USB is off, using USB wakeup asynchronous interrupt. USB bus in suspend mode. | typ 201 uA | 874 |
| Suspend | GCLK_USB is on. USB bus in suspend mode. | typ 0.83 mA | 874 |
| IDLE | Start Of Frame is running. No packet transferred. | typ 1.17 mA | 874 |
| Active OUT | Start Of Frame is running. Bulk OUT on 100% bandwidth. | typ 2.17 mA | 874 |
| Active IN | Start Of Frame is running. Bulk IN on 100% bandwidth. | typ 10.3 mA | 874 |
| Pull-up - Pull-down resistance RPULL | All pins except for PA24 and PA25 | min 20 · typ 40 · max 60 kΩ | 874 |
| Output low-level current IOL | VDD=1.62V-3V, PORT.PINCFG.DRVSTR=0 | max 1 mA | 875 |
| Output low-level current IOL | VDD=3V-3.63V, PORT.PINCFG.DRVSTR=0 | max 2.5 mA | 875 |
| Output low-level current IOL | VDD=1.62V-3V, PORT.PINCFG.DRVSTR=1 | max 3 mA | 875 |
| Output low-level current IOL | VDD=3V-3.63V, PORT.PINCFG.DRVSTR=1 | max 10 mA | 875 |
| Output high-level current IOH | VDD=1.62V-3V, PORT.PINCFG.DRVSTR=0 | max 0.7 mA | 875 |
| Output high-level current IOH | VDD=3V-3.63V, PORT.PINCFG.DRVSTR=0 | max 2 mA | 875 |
| Output high-level current IOH | VDD=1.62V-3V, PORT.PINCFG.DRVSTR=1 | max 2 mA | 875 |
| Output high-level current IOH | VDD=3V-3.63V, PORT.PINCFG.DRVSTR=1 | max 7 mA | 875 |
| Rise time(1) tRISE | PORT.PINCFG.DRVSTR=0; load = 5pF; VDD = 3.3V; based on simulation | max 15 ns | 875 |
| Rise time(1) tRISE | PORT.PINCFG.DRVSTR=1; load = 20pF; VDD = 3.3V; based on simulation | max 15 ns | 875 |
| Fall time(1) tFALL | PORT.PINCFG.DRVSTR=0; load = 5pF; VDD = 3.3V; based on simulation | max 15 ns | 875 |
| Fall time(1) tFALL | PORT.PINCFG.DRVSTR=1; load = 20pF; VDD = 3.3V; based on simulation | max 15 ns | 875 |
| Input leakage current ILEAK | Pull-up resistors disabled | min -1 · max 1 uA | 875 |
| Output low-level voltage VOL | VDD> 2.0V, IOL=3mA | max 0.4 V | 875 |
| Output low-level current IOL | VOL =0.4V; Standard, Fast and HS Modes | min 3 mA | 876 |
| Output low-level current IOL | VOL =0.4V; Fast Mode + | min 20 mA | 876 |
| Output low-level current IOL | VOL =0.6V | min 6 mA | 876 |
| SCL clock frequency fSCL | max 3.4 MHz | 876 | |
| IO pin injection current Iinj1 | Vpin < GND-0.6V or 3.6V<Vpin≤4.2V; 3V<VDD≤3.6V | min -1 · max 1 mA | 876 |
| IO pin injection current Iinj2 | Vpin < GND-0.6V or Vpin≤3.6V; VDD≤3V | min -15 · max 15 mA | 876 |
| Sum of IO pins injection current Iinjtotal | min -45 · max 45 mA | 876 | |
| DC calibrated output voltage VDDCORE | Voltage regulator normal mode | min 1.1 · typ 1.23 · max 1.3 V | 877 |
| Input regulator capacitor, between VDDIN and GND CIN | Ceramic dielectric X7R | typ 10 uF | 877 |
| Input regulator capacitor, between VDDIN and GND CIN | Ceramic dielectric X7R | typ 100 nF | 877 |
| Output regulator capacitor, between VDDCORE and GND COUT | min 0.8 · typ 1 uF | 877 | |
| External Series Resistance of Cout ESR Cout | max 1 Ω | 877 | |
| Voltage threshold on VDD rising VPOT+ | VDD falls at 1V/ms or slower | min 1.27 · typ 1.45 · max 1.58 V | 877 |
| Voltage threshold on VDD falling VPOT- | min 0.72 · typ 0.99 · max 1.32 V | 877 | |
| Power supply voltage VDD | 85°C characteristics | min 0 · max 3.8 V | 864 |
| Current into a VDD pin IVDD | 85°C characteristics; maximum source current 46mA per GPIO cluster | max 92 mA | 864 |
| Current out of a GND pin IGND | 85°C characteristics; maximum sink current 65mA per GPIO cluster | max 130 mA | 864 |
| Storage temperature Tstorage | 85°C characteristics | min -60 · max 150 °C | 864 |
| Power supply voltage VDD | 85°C characteristics; minimum with BOD33 disabled | min 1.62 · typ 3.3 · max 3.63 V | 864 |
| Analog supply voltage VDDANA | 85°C characteristics; minimum with BOD33 disabled | min 1.62 · typ 3.3 · max 3.63 V | 864 |
| Temperature range TA | 85°C characteristics | min -40 · typ 25 · max 85 °C | 864 |
| Junction temperature TJ | 85°C characteristics | max 100 °C | 864 |
| RTC | fGCLK_RTC = 32kHz, 32bit counter mode; incremental peripheral consumption | typ 7.4 uA | 872 |
| WDT | fGCLK_WDT=32kHz, normal mode with EW; incremental peripheral consumption | typ 5.5 uA | 872 |
| ACx | Both fGCLK=8MHz, Enable both COMP; incremental peripheral consumption | typ 31.3 uA | 872 |
| TCC2 | fGCLK=8MHz, Enable + COUNTER; incremental peripheral consumption | typ 95.5 uA | 872 |
| TCC1 | fGCLK=8MHz, Enable + COUNTER; incremental peripheral consumption | typ 167.5 uA | 872 |
| TCC0 | fGCLK=8MHz, Enable + COUNTER; incremental peripheral consumption | typ 180.3 uA | 872 |
| SERCOMx.I2CM | fGCLK=8MHz, Enable; incremental peripheral consumption | typ 69.7 uA | 872 |
| SERCOMx.I2CS | fGCLK=8MHz, Enable; incremental peripheral consumption | typ 29.2 uA | 872 |
| SERCOMx.SPI | fGCLK=8MHz, Enable; incremental peripheral consumption | typ 64.6 uA | 872 |
| SERCOMx.USART | fGCLK=8MHz, Enable; incremental peripheral consumption | typ 65.5 uA | 872 |
| I2S | fGCLK_I2S_0=12.288MHz with source FDPLL with fFDPLL=49,152MHz; includes FDPLL | typ 26.4 uA | 872 |
| DMAC | RAM to RAM transfer; includes RAM R/W access | typ 399.5 uA | 872 |
| Suspend | GCLK_USB is off, using USB wakeup asynchronous interrupt; USB bus in suspend mode; excludes clock source and CPU | typ 201 uA | 873 |
| Suspend | GCLK_USB is on; USB bus in suspend mode; excludes clock source and CPU | typ 0.83 mA | 873 |
| IDLE | Start Of Frame is running; no packet transferred; excludes clock source and CPU | typ 1.17 mA | 873 |
| Active OUT | Start Of Frame is running; Bulk OUT on 100% bandwidth; excludes clock source and CPU | typ 2.17 mA | 873 |
| Active IN | Start Of Frame is running; Bulk IN on 100% bandwidth; excludes clock source and CPU | typ 10.3 mA | 873 |
| Output regulator capacitor, between VDDCORE and GND COUT | Ceramic or solid tantalum capacitor with low ESR <= 1 ohms recommended | min 0.8 · typ 1 uF | 877 |
| Crystal load capacitance CL | max 12.5 pF | 894 | |
| Crystal shunt capacitance CSHUNT | typ 0.1 pF | 894 | |
| Parasitic capacitor load CXIN32 | typ 3.1 pF | 894 | |
| Parasitic capacitor load CXOUT32 | typ 3.3 pF | 894 | |
| Current consumption IXOSC32K | typ 1.22 · max 2.19 uA | 894 | |
| Crystal equivalent series resistance ESR | CL=12.5pF; f=32.768kHz; Safety Factor = 3 | max 141 kΩ | 894 |
| Output frequency fOUT | DFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512; after calibration at room temperature | min 47 · typ 48 · max 49 MHz | 894 |
| Power consumption on VDDIN IDFLL | IDFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512 | typ 403 · max 453 uA | 894 |
| Start-up time tSTARTUP | DFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512; fOUT within 90 % of final value | typ 8 · max 9 us | 894 |
| Current consumption IOSC8M | IDLE2 on OSC32K versus IDLE2 on calibrated OSC8M enabled at 8MHz (FRANGE=1, PRESC=0) | typ 64 · max 96 uA | 897 |
| Startup time tSTARTUP | typ 2.4 · max 3.3 us | 897 | |
| Duty cycle Duty | typ 50 % | 897 | |
| Input frequency fIN | Device Variant A | min 32 · max 2000 KHz | 897 |
| Output frequency fOUT | Device Variant A | min 48 · max 96 MHz | 897 |
| Current consumption IFDPLL96M | Device Variant A; fIN= 32 kHz, fOUT= 48 MHz | typ 500 · max 700 uA | 897 |
| Current consumption IFDPLL96M | Device Variant A; fIN= 32 kHz, fOUT= 96 MHz | typ 900 · max 1200 uA | 897 |
| Period jitter Jp | Device Variant A; fIN= 32 kHz, fOUT= 48 MHz | typ 1.5 · max 2 % | 897 |
| Period jitter Jp | Device Variant A; fIN= 32 kHz, fOUT= 96 MHz | typ 3 · max 10 % | 897 |
| Period jitter Jp | Device Variant A; fIN= 2 MHz, fOUT= 48 MHz | typ 1.3 · max 2 % | 897 |
| Period jitter Jp | Device Variant A; fIN= 2 MHz, fOUT= 96 MHz | typ 3 · max 7 % | 897 |
| Lock Time tLOCK | Device Variant A; after start-up, time to get lock signal; fIN= 32 kHz, fOUT= 96 MHz | typ 1.3 · max 2 ms | 897 |
| Lock Time tLOCK | Device Variant A; after start-up, time to get lock signal; fIN= 2 MHz, fOUT= 96 MHz | typ 25 · max 50 us | 897 |
| Duty cycle Duty | Device Variant A | min 40 · typ 50 · max 60 % | 897 |
| Power supply voltage VDD | 105°C characteristics | min 0 · max 3.8 V | 916 |
| Current into a VDD pin IDD | 105°C characteristics; maximum source current 46mA per GPIO cluster | max 92 mA | 916 |
| Current out of a GND pin IGND | 105°C characteristics; maximum sink current 65mA per GPIO cluster | max 130 mA | 916 |
| Storage temperature Tstorgae | 105°C characteristics | min -60 · max 150 °C | 916 |
| Power supply voltage VDD | 105°C characteristics; minimum with BOD33 disabled | min 1.62 · typ 3.3 · max 3.63 V | 916 |
| Analog supply voltage VDDANA | 105°C characteristics; minimum with BOD33 disabled | min 1.62 · typ 3.3 · max 3.63 V | 916 |
| Temperature range TA | 105°C characteristics | min -40 · typ 25 · max 105 °C | 916 |
| Junction temperature TJ | 105°C characteristics | max 125 °C | 916 |
| ACTIVE | 105°C; CPU running a While(1) algorithm | typ 2.55 · max 2.75 mA | 919 |
| ACTIVE | 105°C; CPU running a While(1) algorithm; VDDIN=1.8V; Flash with 3 wait states | typ 2.56 · max 2.82 mA | 919 |
| ACTIVE | 105°C; CPU running a Fibonacci algorithm | typ 4.21 · max 4.59 mA | 919 |
| ACTIVE | 105°C; CPU running a Fibonacci algorithm; VDDIN=1.8V; Flash with 3 wait states | typ 4.23 · max 4.57 mA | 919 |
| ACTIVE | 105°C; CPU running a CoreMark algorithm | typ 6.02 · max 6.54 mA | 919 |
| ACTIVE | 105°C; CPU running a CoreMark algorithm; VDDIN=1.8V; Flash with 3 wait states | typ 5.21 · max 5.57 mA | 919 |
| IDLE0 | 105°C | typ 1.55 · max 1.62 mA | 919 |
| IDLE1 | 105°C | typ 1.13 · max 1.18 mA | 919 |
| IDLE2 | 105°C | typ 0.96 · max 1.01 mA | 919 |
| STANDBY | 105°C; rev. E silicon; XOSC32K running / RTC running at 1kHz | typ 214 · max 627 uA | 919 |
| STANDBY | 105°C; rev. E silicon; XOSC32K and RTC stopped | typ 212 · max 624 uA | 919 |
| STANDBY | 105°C; rev. F silicon; XOSC32K running / RTC running at 1kHz | typ 175 · max 452 uA | 919 |
| STANDBY | 105°C; rev. F silicon; XOSC32K and RTC stopped | typ 173 · max 450 uA | 919 |
| Output frequency fOUT | 105°C characteristics; IDFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512 | min 47 · typ 48 · max 49 MHz | 932 |
| Power consumption on VDDIN IDFLL | 105°C characteristics; IDFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512 | typ 403 · max 453 uA | 932 |
| Startup time tSTARTUP | 105°C characteristics; DFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512; fOUT within 90 % of final value | typ 8 · max 9 us | 932 |
| Average Output frequency fOUT | 105°C characteristics; fREF = 32.768kHz | min 47.76 · typ 48 · max 48.24 MHz | 932 |
| Reference frequency fREF | 105°C characteristics | min 0.732 · typ 32.768 · max 33 kHz | 932 |
| Period Jitter Jitter | 105°C characteristics; fREF = 32.768kHz | max 0.42 ns | 932 |
| Power consumption on VDDIN IDFLL | 105°C characteristics; fREF = 32.768kHz | typ 403 · max 453 uA | 932 |
| Lock time tLOCK | 105°C characteristics; fREF = 32.768kHz; DFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512; DFLLCTRL.BPLCKC = 1; DFLLCTRL.QLDIS = 0; DFLLCTRL.CCDIS = 1; DFLLMUL.FSTEP = 10 | typ 200 · max 500 us | 932 |
| Output frequency fOUT | Calibrated against a 32.768 kHz reference at 25°C, over [-40, +105]°C, over [1.62, 3.63]V | min 28.508 · typ 32.768 · max 35.132 kHz | 932 |
| Output frequency fOUT | Calibrated against a 32.768 kHz reference at 25°C, at VDD = 3.3V | min 32.276 · typ 32.768 · max 33.26 kHz | 932 |
| Output frequency fOUT | Calibrated against a 32.768 kHz reference at 25°C, over [1.62, 3.63]V | min 31.457 · typ 32.768 · max 34.079 kHz | 932 |
| Current consumption IOSC32K | 105°C characteristics | typ 0.67 · max 1.9 uA | 932 |
| Startup time tSTARTUP | 105°C characteristics | typ 1 · max 2 cycle | 932 |
| Duty Cycle Duty | 105°C characteristics | typ 50 % | 932 |
| Output frequency fOUT | Calibrated against a 32.768 kHz reference at 25°C, over [-40, +105]°C, over [1.62, 3.63]V | min 25.559 · typ 32.768 · max 40.305 kHz | 933 |
| Output frequency fOUT | Calibrated against a 32.768 kHz reference at 25°C, at VDD = 3.3V | min 31.293 · typ 32.768 · max 34.57 kHz | 933 |
| Output frequency fOUT | Calibrated against a 32.768 kHz reference at 25°C, over [1.62, 3.63]V | min 31.293 · typ 32.768 · max 34.57 kHz | 933 |
| Duty cycle Duty | 105°C characteristics | typ 50 % | 933 |
| Output frequency fOUT | Calibrated against a 8 MHz reference at 25°C, over [-40, +105]°C, over [1.62, 3.63]V | min 7.65 · typ 8 · max 8.17 MHz | 933 |
| Output frequency fOUT | Calibrated against a 8 MHz reference at 25°C, at VDD = 3.3V | min 7.94 · typ 8 · max 8.06 MHz | 933 |
| Output frequency fOUT | Calibrated against a 8 MHz reference at 25°C, over [1.62, 3.63]V | min 7.92 · typ 8 · max 8.08 MHz | 933 |
| Frequency vs. temperature drift TempCo | 105°C characteristics; unit not printed | min -1.2 · max 1 | 933 |
| Frequency vs. supply drift SupplyCo | 105°C characteristics; unit not printed | min -2 · max 2 | 933 |
| Current consumption IOSC8M | 105°C characteristics; IDLE2 on OSC32K versus IDLE2 on calibrated OSC8M enabled at 8 MHz (FRANGE = 1, PRESC = 0) | typ 64 · max 96 uA | 933 |
| Startup time tSTARTUP | 105°C characteristics | typ 2.4 · max 3.3 us | 933 |
| Duty cycle Duty | 105°C characteristics | typ 50 % | 933 |
| Input frequency fIN | 105°C characteristics; Silicon Revision F and G | min 32 · max 2000 KHz | 934 |
| Output frequency fOUT | 105°C characteristics; Silicon Revision F and G | min 48 · max 96 MHz | 934 |
| Current consumption IFDPLL96M | 105°C characteristics; Silicon Revision F and G; fIN= 32 kHz, fOUT= 48 MHz | typ 500 uA | 934 |
| Current consumption IFDPLL96M | 105°C characteristics; Silicon Revision F and G; fIN= 32 kHz, fOUT= 96 MHz | typ 900 uA | 934 |
| Period jitter Jp | 105°C characteristics; Silicon Revision F and G; fIN= 32 kHz, fOUT= 48 MHz | typ 2.1 · max 3 % | 934 |
| Period jitter Jp | 105°C characteristics; Silicon Revision F and G; fIN= 32 kHz, fOUT= 96 MHz | typ 3.8 · max 9.2 % | 934 |
| Period jitter Jp | 105°C characteristics; Silicon Revision F and G; fIN= 2 MHz, fOUT= 48 MHz | typ 2.2 · max 3.2 % | 934 |
| Period jitter Jp | 105°C characteristics; Silicon Revision F and G; fIN= 2 MHz, fOUT= 96 MHz | typ 4.4 · max 10 % | 934 |
| Lock Time tLOCK | 105°C characteristics; Silicon Revision F and G; after startup, time to get lock signal; fIN= 32 kHz, fOUT= 96 MHz | typ 1.2 · max 2 ms | 934 |
| Lock Time tLOCK | 105°C characteristics; Silicon Revision F and G; fIN= 2 MHz, fOUT= 96 MHz | typ 25 · max 50 us | 934 |
| Duty cycle Duty | 105°C characteristics; Silicon Revision F and G | min 40 · typ 50 · max 60 % | 934 |
| Power supply voltage VDD | 125°C characteristics | min 0 · max 3.8 V | 936 |
| Current into a VDD pin IVDD | 125°C characteristics; maximum source current 14mA per GPIO cluster | max 28 mA | 936 |
| Current out of a GND pin IGND | 125°C characteristics; maximum sink current 19.5mA per GPIO cluster | max 39 mA | 936 |
| Storage temperature Tstorage | 125°C characteristics | min -60 · max 150 °C | 936 |
| Power supply voltage VDD | 125°C characteristics; minimum with BOD33 disabled | min 1.62 · typ 3.3 · max 3.63 V | 936 |
| Analog supply voltage VDDANA | 125°C characteristics; minimum with BOD33 disabled | min 1.62 · typ 3.3 · max 3.63 V | 936 |
| Temperature range TA | 125°C characteristics | min -40 · typ 25 · max 125 °C | 936 |
| Junction temperature TJ | 125°C characteristics | max 145 °C | 936 |
| ACTIVE | 125°C; CPU running a While(1) algorithm; Silicon Revision F | typ 3.75 · max 4.12 mA | 941 |
| ACTIVE | 125°C; CPU running a While(1) algorithm; VDDIN=1.8V; Flash with 3 wait states; Silicon Revision F | typ 3.77 · max 4.13 mA | 941 |
| ACTIVE | 125°C; CPU running a Fibonacci algorithm; Silicon Revision F | typ 4.85 · max 5.29 mA | 941 |
| ACTIVE | 125°C; CPU running a Fibonacci algorithm; VDDIN=1.8V; Flash with 3 wait states; Silicon Revision F | typ 4.87 · max 5.29 mA | 941 |
| ACTIVE | 125°C; CPU running a CoreMark algorithm; Silicon Revision F | typ 6.7 · max 7.3 mA | 941 |
| ACTIVE | 125°C; CPU running a CoreMark algorithm; VDDIN=1.8V; Flash with 3 wait states; Silicon Revision F | typ 5.98 · max 6.41 mA | 941 |
| IDLE0 | 125°C; Default operating conditions; Silicon Revision F | typ 2.4 · max 2.69 mA | 941 |
| IDLE1 | 125°C; Default operating conditions; Silicon Revision F | typ 1.79 · max 2.05 mA | 941 |
| IDLE2 | 125°C; Default operating conditions; Silicon Revision F | typ 1.5 · max 1.76 mA | 941 |
| Output frequency fOUT | Device Variant A; IDFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512; open loop after calibration at room temperature | min 47 · typ 48 · max 49 MHz | 959 |
| Power consumption on VDDIN IDFLL | Device Variant A; IDFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512; open loop after calibration at room temperature | typ 403 · max 457 uA | 959 |
| Start-up time tSTARTUP | Device Variant A; IDFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512; fOUT within 90 % of final value; open loop after calibration at room temperature | min 7 · typ 8 · max 9 us | 959 |
| Average Output frequency fOUT | Device Variant A; fREF = 32 .768kHz | min 47.76 · typ 48 · max 48.24 MHz | 959 |
| Reference frequency fREF | Device Variant A | min 0.732 · typ 32.768 · max 33 kHz | 959 |
| Cycle to Cycle jitter Jitter | Device Variant A; fREF = 32 .768kHz | max 1.04 ns | 959 |
| Power consumption on VDDIN IDFLL | Device Variant A; fREF = 32 .768kHz | typ 425 · max 482 uA | 960 |
| Lock time tLOCK | Device Variant A; fREF = 32 .768kHz; DFLLVAL.COARSE = DFLL48M COARSE CAL; DFLLVAL.FINE = 512; DFLLCTRL.BPLCKC = 1; DFLLCTRL.QLDIS = 0; DFLLCTRL.CCDIS = 1; DFLLMUL.FSTEP = 10 | min 100 · typ 200 · max 500 us | 960 |
| Output frequency fOUT | Device Variant A; Calibrated against a 32.768 kHz reference at 25°C, over [-40, +125]°C, over [1.62, 3.63]V | min 28.508 · typ 32.768 · max 35.389 kHz | 960 |
| Output frequency fOUT | Device Variant A; Calibrated against a 32.768 kHz reference at 25°C, at VDD = 3.3V | min 32.276 · typ 32.768 · max 33.26 kHz | 960 |
| Output frequency fOUT | Device Variant A; Calibrated against a 32.768 kHz reference at 25°C, over [1.62, 3.63]V | min 31.457 · typ 32.768 · max 34.079 kHz | 960 |
| Current consumption IOSC32K | Device Variant A | typ 0.79 · max 1.8 uA | 960 |
| Start-up time tSTARTUP | Device Variant A | typ 1 · max 2 cycle | 960 |
| Duty Cycle Duty | Device Variant A | typ 50 % | 960 |
| Output frequency fOUT | Device Variant A; Calibrated against a 8MHz reference at 25°C, over [-40, +125]°C, over [1.62, 3.63]V | min 7.54 · typ 8 · max 8.19 MHz | 962 |
| Output frequency fOUT | Device Variant A; Calibrated against a 8MHz reference at 25°C, at VDD=3.3V | min 7.94 · typ 8 · max 8.06 MHz | 962 |
| Output frequency fOUT | Device Variant A; Calibrated against a 8MHz reference at 25°C, over [1.62, 3.63]V | min 7.92 · typ 8 · max 8.08 MHz | 962 |
| Current consumption IOSC8M | Device Variant A; IIDLEIDLE2 on OSC32K versus IDLE2 on calibrated OSC8M enabled at 8MHz (FRANGE=1, PRESC=0) | typ 64 · max 100 uA | 962 |
| Startup time tSTARTUP | Device Variant A | typ 2.1 · max 3 us | 962 |
| Duty cycle Duty | Device Variant A | typ 50 % | 962 |
| Input frequency fIN | Device Variant A; FILTSEL[1/0] default value | min 32 · max 2000 KHz | 962 |
| Output frequency fOUT | Device Variant A; FILTSEL[1/0] default value | min 48 · max 96 MHz | 962 |
| Current consumption IFDPLL96M | Device Variant A; fIN= 32 kHz, fOUT= 48 MHz; FILTSEL[1/0] default value | typ 500 · max 700 uA | 962 |
| Current consumption IFDPLL96M | Device Variant A; fIN= 32 kHz, fOUT= 96 MHz; FILTSEL[1/0] default value | typ 900 · max 1200 uA | 962 |
| Period jitter Jp | Device Variant A; fIN= 32 kHz, fOUT= 48 MHz; FILTSEL[1/0] default value | typ 1.5 · max 2 % | 962 |
| Period jitter Jp | Device Variant A; fIN= 32 kHz, fOUT= 96 MHz; FILTSEL[1/0] default value | typ 3 · max 10 % | 962 |
| Period jitter Jp | Device Variant A; fIN= 2 MHz, fOUT= 48 MHz; FILTSEL[1/0] default value | typ 1.3 · max 2 % | 962 |
| Period jitter Jp | Device Variant A; fIN= 2 MHz, fOUT= 96 MHz; FILTSEL[1/0] default value | typ 3 · max 7 % | 962 |
| Lock Time tLOCK | Device Variant A; After start-up, time to get lock signal; fIN= 32 kHz, fOUT= 96 MHz; FILTSEL[1/0] default value | typ 1.3 · max 2 ms | 962 |
| Lock Time tLOCK | Device Variant A; After start-up, time to get lock signal; fIN= 2 MHz, fOUT= 96 MHz; FILTSEL[1/0] default value | typ 25 · max 50 us | 962 |
| Duty cycle Duty | Device Variant A; FILTSEL[1/0] default value | min 40 · typ 50 · max 60 % | 963 |
- 4 layers70.8 × 108 mm

- 2 layers36 × 20 mm

- 4 layers35.1 × 76.3 mm

Tiny4FSK
New-England-Weather-Balloon-Society/Tiny4FSK
Horus Binary v2 HAB Tracker
90 parts96CERN-OHL-W-2.0 - 4 layers36.6 × 60.3 mm

StratoSoar MK3.0
crnicholson/StratoSoar-MK3
StratoSoar MK3, an autonomous glider meant for high-altitudes, accessible to everyone
85 parts43 - 4 layers42 × 83.9 mm

StratoSoar MK2.2
crnicholson/StratoSoar-MK2
StratoSoar is an engineering project that aims to be able to fly a glider (dropped from a high-altitude balloon), down to any selected coordinates.
116 parts24 - 2 layers69.8 × 40.4 mm

T Piece Kicad
calebmarting/os2026-badge
Schematics and firmware for the Open Sauce 2026 Badge and SAOs
82 parts23MIT - 2 layers51.8 × 51.8 mm

Pawpet
NanoCodeBug/pawpet
A virtual pet using the atsamd21g and sharp memory lcd, runs off of 2xAAA for a couple of months. See PawPet on Hacakday.io for full gallery.
41 parts20 - 4 layers117 × 107 mm

Mainboard dual battery
shurik179/yozh
Small robot based on Pololu's Zumo chassis but programmable in CircuitPython
121 parts8MIT
Parts like it
8STM32F103C8T6
LQFP-48(7x7)-40℃~+85℃ 12bit 20KB 2V~3.6V 32 Bit 37 64KB 72MHz ARM Cortex-M3 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)STM32F030C8T6
LQFP-48(7x7)-40℃~+85℃ 12bit 2.4V~3.6V 32 Bit 39 48MHz 64KB 8KB ARM Cortex-M0 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)STM32G070CBT6
LQFP-48(7x7)-40℃~+85℃ 128KB 2V~3.6V 32 Bit 36KB 43 64MHz ARM Cortex-M0+ Built-in+External FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)STM32G030C8T6
LQFP-48(7x7)-40℃~+85℃ 12bit 2V~3.6V 32 Bit 44 64KB 64MHz 8KB ARM Cortex-M0+ Built-in+External FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)GD32F303CCT6
LQFP-48(7x7)120MHz 12bit 12bit 2.6V~3.6V 256KB 37 ARM Cortex-M4 FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSGigaDeviceMicrocontrollers (MCU/MPU/SOC)GD32F103C8T6
LQFP-48(7x7)108MHz 12bit 2.6V~3.6V 37 64KB ARM Cortex-M3 FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSGigaDeviceMicrocontrollers (MCU/MPU/SOC)STM32F030C6T6
LQFP-48(7x7)-40℃~+85℃ 12bit 2.4V~3.6V 32 Bit 32KB 39 48MHz 4KB ARM Cortex-M0 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)GD32F103CBT6
LQFP-48(7x7)108MHz 128KB 12bit 2.6V~3.6V 37 ARM Cortex-M3 FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSGigaDeviceMicrocontrollers (MCU/MPU/SOC)
Questions
Is there a KiCad symbol and footprint for the ATSAMD21G18A-AU?
Yes. The symbol is MCU_Microchip_SAMD:ATSAMD21G18A-A and the footprint Package_QFP:TQFP-48_7x7mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the ATSAMD21G18A-AU?
TQFP-48, with 48 pins. Its footprint is drawn on this page.
Where is the ATSAMD21G18A-AU datasheet?
Microchip Technology publishes it: the Datasheet link on this page opens it.
Where can I order the ATSAMD21G18A-AU?
JLCPCB lists it as part C78624, with 4,184 in stock; the sellers' links on this page open their listings.
What can replace the ATSAMD21G18A-AU?
Parts like it in the library: the STM32F103C8T6 by STMicroelectronics, the STM32F030C8T6 by STMicroelectronics, the STM32G070CBT6 by STMicroelectronics and the STM32G030C8T6 by STMicroelectronics. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the ATSAMD21G18A-AU?
70 boards in 58 repositories on GitHub; the most starred are listed on this page, with their KiCad files.