
Coin Cell Tester
tomrodinger/servomotor
Open-source NEMA-17 integrated servomotor (motor + closed-loop driver + controller + encoder). RS-485, Python/Arduino libraries, MCP server for AI control. Hardware, firmware and software.
STMicroelectronicsExtended
-40℃~+85℃ 12bit 2V~3.6V 32 Bit 44 64KB 64MHz 8KB ARM Cortex-M0+ Built-in+External FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHS
The STM32G030C8T6 is a microcontroller made by STMicroelectronics in a LQFP-48(7x7) package with 48 pins. -40℃~+85℃ 12bit 2V~3.6V 32 Bit 44 64KB 64MHz 8KB ARM Cortex-M0+ Built-in+External FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHS.
PCBKit's library has its KiCad symbol (MCU_ST_STM32G0:STM32G030C8Tx, from KiCad's library) and its footprint (Package_QFP:LQFP-48_7x7mm_P0.5mm, from KiCad's library), ready for a KiCad board. 25,131 are in stock at JLCPCB (part C529329). 15 open-source boards in 9 repositories on GitHub use it.
| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| External supply voltage VDD | min -0.3 · max 4 V | 40 | |
| External supply voltage on VBAT pin VBAT | min -0.3 · max 4 V | 40 | |
| External voltage on VREF+ pin VREF+ | Maximum: Min(VDD + 0.4, 4.0) | min -0.3 V | 40 |
| Input voltage on FT_xx VIN | Maximum: VDD + 4.0; internal pull-up/pull-down disabled above 4 V | min -0.3 V | 40 |
| Input voltage on any other pin VIN | min -0.3 · max 4 V | 40 | |
| Current into VDD/VDDA power pin (source) IVDD/VDDA | max 100 mA | 40 | |
| Current out of VSS/VSSA ground pin (sink) IVSS/VSSA | max 100 mA | 40 | |
| Output current sunk by any I/O and control pin except FT_f IIO(PIN) | max 15 mA | 40 | |
| Output current sunk by any FT_f pin IIO(PIN) | max 20 mA | 40 | |
| Output current sourced by any I/O and control pin IIO(PIN) | max 15 mA | 40 | |
| Total output current sunk by sum of all I/Os and control pins ∑IIO(PIN) | max 80 mA | 40 | |
| Total output current sourced by sum of all I/Os and control pins ∑IIO(PIN) | max 80 mA | 40 | |
| Injected current on a FT_xx pin IINJ(PIN) | Negative injection limit; positive injection NA | max -5 mA | 40 |
| Total injected current (sum of all I/Os and control pins) ∑|IINJ(PIN)| | Absolute sum of negative injected currents | max 25 mA | 40 |
| Storage temperature range TSTG | min -65 · max 150 °C | 41 | |
| Maximum junction temperature TJ | max 150 °C | 41 | |
| Internal AHB clock frequency fHCLK | min 0 · max 64 MHz | 41 | |
| Internal APB clock frequency fPCLK | min 0 · max 64 MHz | 41 | |
| Supply voltage VDD/DDA | When RESET is released functionality is guaranteed down to VPDR min | min 2 · max 3.6 V | 41 |
| Backup operating voltage VBAT | min 1.55 · max 3.6 V | 41 | |
| I/O input voltage VIN | Maximum: Min(VDD + 3.6, 5.5); internal pull-up/pull-down disabled above VDD + 0.3 V | min -0.3 V | 41 |
| Ambient temperature TA | TA(max) applies at PD(max) | min -40 · max 85 °C | 41 |
| Junction temperature TJ | min -40 · max 105 °C | 41 | |
| VDD slew rate tVDD | VDD falling; maximum ∞ | min 10 us/V | 41 |
| POR temporization when VDD crosses VPOR tRSTTEMPO | VDD rising; guaranteed by design | typ 250 · max 400 us | 42 |
| Power-on reset threshold VPOR | Guaranteed by design | min 2.06 · typ 2.1 · max 2.14 V | 42 |
| Power-down reset threshold VPDR | Guaranteed by design | min 1.96 · typ 2 · max 2.04 V | 42 |
| Hysteresis of VPOR and VPDR Vhyst_POR_PDR | Hysteresis in continuous mode | typ 20 mV | 42 |
| Hysteresis of VPOR and VPDR Vhyst_POR_PDR | Hysteresis in other mode | typ 30 mV | 42 |
| Internal reference voltage VREFINT | -40°C < TJ < 105°C | min 1.182 · typ 1.212 · max 1.232 V | 42 |
| ADC sampling time when reading the internal reference voltage tS_vrefint | Guaranteed by design | min 4 us | 42 |
| Start time of reference voltage buffer when ADC is enable tstart_vrefint | Maximum guaranteed by design | typ 8 · max 12 us | 42 |
| VREFINT buffer consumption from VDD when converted by ADC IDD(VREFINTBUF) | Maximum guaranteed by design | typ 12.5 · max 20 uA | 42 |
| Internal reference voltage spread over the temperature range ∆VREFINT | VDD = 3 V; maximum guaranteed by design | typ 5 · max 7.5 mV | 42 |
| Temperature coefficient TCoeff_vrefint | Maximum guaranteed by design | typ 30 · max 50 ppm/°C | 42 |
| Long term stability ACoeff | 1000 hours, T = 25 °C; maximum guaranteed by design | typ 300 · max 1000 ppm | 42 |
| Voltage coefficient VDDCoeff | 3.0 V < VDD < 3.6 V; maximum guaranteed by design | typ 250 · max 1200 ppm/V | 42 |
| 1/4 reference voltage VREFINT_DIV1 | min 24 · typ 25 · max 26 % VREFINT | 42 | |
| 1/2 reference voltage VREFINT_DIV2 | min 49 · typ 50 · max 51 % VREFINT | 42 | |
| 3/4 reference voltage VREFINT_DIV3 | min 74 · typ 75 · max 76 % VREFINT | 42 | |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, Flash, 64 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 5.7 · max 8 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, Flash, 64 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 5.9 · max 8.3 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, Flash, 56 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 5.1 · max 7.1 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, Flash, 56 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 5.2 · max 7.1 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, Flash, 48 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 4.6 · max 5.7 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, Flash, 48 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 4.7 · max 6 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, Flash, 32 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 3.2 · max 4.6 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, Flash, 32 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 3.3 · max 4.9 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, Flash, 24 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 2.5 · max 3.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, Flash, 24 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 2.6 · max 3.8 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, HSI bypass, Flash, 16 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 1.6 · max 2.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, HSI bypass, Flash, 16 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 1.7 · max 2.9 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, SRAM, 64 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 4.7 · max 7.2 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, SRAM, 64 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 4.8 · max 7.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, SRAM, 56 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 4.2 · max 6.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, SRAM, 56 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 4.3 · max 6.7 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, SRAM, 48 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 3.7 · max 5.7 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, SRAM, 48 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 3.9 · max 6 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, SRAM, 32 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 2.6 · max 4.1 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, SRAM, 32 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 2.7 · max 4.3 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, SRAM, 24 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 2 · max 3.2 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, SRAM, 24 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 2.1 · max 3.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, HSI bypass, SRAM, 16 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 1.3 · max 2.3 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1, PLL enabled, HSI bypass, SRAM, 16 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 1.3 · max 2.4 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, Flash, 16 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 1.3 · max 2 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, Flash, 16 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 1.3 · max 2.3 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, Flash, 8 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 0.7 · max 1.4 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, Flash, 8 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 0.8 · max 1.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, Flash, 2 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 0.3 · max 0.6 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, Flash, 2 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 0.3 · max 0.9 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, SRAM, 16 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 1.1 · max 1.9 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, SRAM, 16 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 1.1 · max 2.1 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, SRAM, 8 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 0.6 · max 1.2 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, SRAM, 8 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 0.6 · max 1.4 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, SRAM, 2 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 0.2 · max 0.6 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2, PLL enabled, HSI bypass, SRAM, 2 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 0.3 · max 0.9 mA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, Flash, 2 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 182 · max 570 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, Flash, 2 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 226 · max 790 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, Flash, 1 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 99 · max 480 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, Flash, 1 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 132 · max 700 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, Flash, 500 kHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 58 · max 430 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, Flash, 500 kHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 89 · max 630 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, Flash, 125 kHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 56 · max 600 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, LSE bypass, Flash, 32 kHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 17 · max 330 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, LSE bypass, Flash, 32 kHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 47 · max 480 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, SRAM, 2 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 191 · max 800 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, SRAM, 1 MHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 91 · max 470 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, SRAM, 1 MHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 114 · max 750 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, SRAM, 500 kHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 48 · max 410 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, SRAM, 500 kHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 81 · max 710 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, SRAM, 125 kHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 21 · max 360 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, HSE bypass, SRAM, 125 kHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 51 · max 500 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, LSE bypass, SRAM, 32 kHz, 25°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 15 · max 310 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled, LSE bypass, SRAM, 32 kHz, 85°C; typ VDD=3.0 V, max VDD=3.6 V; all peripherals disabled | typ 37 · max 400 uA | 44 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL enabled, 64 MHz, 25°C | typ 1.4 · max 2.2 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL enabled, 64 MHz, 85°C | typ 1.5 · max 2.4 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL enabled, 56 MHz, 25°C | typ 1.3 · max 1.9 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL enabled, 56 MHz, 85°C | typ 1.4 · max 2.1 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL enabled, 48 MHz, 25°C | typ 1.2 · max 1.9 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL enabled, 48 MHz, 85°C | typ 1.2 · max 1.9 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL enabled, 32 MHz, 25°C | typ 0.9 · max 1.4 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL enabled, 32 MHz, 85°C | typ 0.9 · max 1.5 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL enabled, 24 MHz, 25°C | typ 0.7 · max 1.1 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL enabled, 24 MHz, 85°C | typ 0.8 · max 1.3 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL disabled, HSE bypass, 16 MHz, 25°C | typ 0.4 · max 0.7 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 1, PLL disabled, HSE bypass, 16 MHz, 85°C | typ 0.4 · max 0.8 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 2, PLL disabled, HSE bypass, 16 MHz, 25°C | typ 0.3 · max 0.6 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 2, PLL disabled, HSE bypass, 16 MHz, 85°C | typ 0.4 · max 0.7 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 2, PLL disabled, HSE bypass, 8 MHz, 25°C | typ 0.2 · max 0.3 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 2, PLL disabled, HSE bypass, 8 MHz, 85°C | typ 0.3 · max 0.6 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 2, PLL disabled, HSE bypass, 2 MHz, 25°C | typ 0.1 · max 0.2 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash enabled, all peripherals disabled, Range 2, PLL disabled, HSE bypass, 2 MHz, 85°C | typ 0.2 · max 0.5 mA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash disabled, PLL disabled, all peripherals disabled, HSE bypass, 2 MHz, 25°C | typ 43 · max 175 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash disabled, PLL disabled, all peripherals disabled, HSE bypass, 2 MHz, 85°C | typ 77 · max 410 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash disabled, PLL disabled, all peripherals disabled, HSE bypass, 1 MHz, 25°C | typ 29 · max 150 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash disabled, PLL disabled, all peripherals disabled, HSE bypass, 1 MHz, 85°C | typ 60 · max 375 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash disabled, PLL disabled, all peripherals disabled, HSE bypass, 500 kHz, 25°C | typ 23 · max 145 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash disabled, PLL disabled, all peripherals disabled, HSE bypass, 500 kHz, 85°C | typ 52 · max 285 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash disabled, PLL disabled, all peripherals disabled, HSE bypass, 125 kHz, 25°C | typ 16 · max 130 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash disabled, PLL disabled, all peripherals disabled, HSE bypass, 125 kHz, 85°C | typ 46 · max 270 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash disabled, PLL disabled, all peripherals disabled, LSE bypass, 32 kHz, 25°C | typ 13 · max 125 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash disabled, PLL disabled, all peripherals disabled, LSE bypass, 32 kHz, 85°C | typ 44 · max 260 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON, VDD=2.4 V, 25°C | typ 290 · max 395 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON, VDD=2.4 V, 85°C | typ 320 · max 540 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON, VDD=3 V, 25°C | typ 295 · max 415 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON, VDD=3 V, 85°C | typ 325 · max 580 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON, VDD=3.6 V, 25°C | typ 295 · max 445 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON, VDD=3.6 V, 85°C | typ 325 · max 595 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF, VDD=2.4 V, 25°C | typ 105 · max 145 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF, VDD=2.4 V, 85°C | typ 145 · max 265 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF, VDD=3 V, 25°C | typ 105 · max 150 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF, VDD=3 V, 85°C | typ 150 · max 285 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF, VDD=3.6 V, 25°C | typ 110 · max 150 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF, VDD=3.6 V, 85°C | typ 150 · max 295 uA | 45 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC disabled, VDD=2.4 V, 25°C | typ 3.4 · max 17 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC disabled, VDD=2.4 V, 85°C | typ 28 · max 130 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC disabled, VDD=3 V, 25°C | typ 3.6 · max 22 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC disabled, VDD=3 V, 85°C | typ 28 · max 140 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC disabled, VDD=3.6 V, 25°C | typ 3.9 · max 28 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC disabled, VDD=3.6 V, 85°C | typ 29 · max 155 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC enabled, LSE bypass, VDD=2.4 V, 25°C | typ 3.9 · max 22 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC enabled, LSE bypass, VDD=2.4 V, 85°C | typ 28 · max 140 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC enabled, LSE bypass, VDD=3 V, 25°C | typ 4.1 · max 23 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC enabled, LSE bypass, VDD=3 V, 85°C | typ 29 · max 155 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC enabled, LSE bypass, VDD=3.6 V, 25°C | typ 4.6 · max 28 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash not powered, RTC enabled, LSE bypass, VDD=3.6 V, 85°C | typ 29 · max 160 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled, VDD=2.4 V, 25°C | typ 1 · max 2.1 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled, VDD=2.4 V, 85°C | typ 1.8 · max 14 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled, VDD=3.0 V, 25°C | typ 1.2 · max 2.7 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled, VDD=3.0 V, 85°C | typ 2.1 · max 16 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled, VDD=3.6 V, 25°C | typ 1.4 · max 3 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled, VDD=3.6 V, 85°C | typ 2.5 · max 19 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, LSI, VDD=2.4 V, 25°C | typ 1.3 · max 2.2 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, LSI, VDD=2.4 V, 85°C | typ 2.1 · max 17 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, LSI, VDD=3.0 V, 25°C | typ 1.7 · max 2.9 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, LSI, VDD=3.0 V, 85°C | typ 2.5 · max 19 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, LSI, VDD=3.6 V, 25°C | typ 2.1 · max 3.8 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, LSI, VDD=3.6 V, 85°C | typ 3 · max 19 uA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE bypass at 32.768 kHz, VBAT=2.4 V, 25°C | typ 270 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE bypass at 32.768 kHz, VBAT=2.4 V, 85°C | typ 360 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE bypass at 32.768 kHz, VBAT=3.0 V, 25°C | typ 360 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE bypass at 32.768 kHz, VBAT=3.0 V, 85°C | typ 460 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE bypass at 32.768 kHz, VBAT=3.6 V, 25°C | typ 470 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE bypass at 32.768 kHz, VBAT=3.6 V, 85°C | typ 600 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE crystal at 32.768 kHz, VBAT=2.4 V, 25°C | typ 410 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE crystal at 32.768 kHz, VBAT=2.4 V, 85°C | typ 440 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE crystal at 32.768 kHz, VBAT=3.0 V, 25°C | typ 510 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE crystal at 32.768 kHz, VBAT=3.0 V, 85°C | typ 530 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE crystal at 32.768 kHz, VBAT=3.6 V, 25°C | typ 630 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, LSE crystal at 32.768 kHz, VBAT=3.6 V, 85°C | typ 770 nA | 46 |
| Electrostatic discharge voltage (human body model) VESD(HBM) | TA = +25 °C, conforming to ANSI/ESDA/JEDEC JS-001; class 1C; based on characterization, not tested in production | max 1000 V | 58 |
| Electrostatic discharge voltage (charge device model) VESD(CDM) | TA = +25 °C, conforming to ANSI/ESDA/JEDEC JS-002; class C2a; based on characterization, not tested in production | max 500 V | 58 |
| Thermal resistance Θ | LQFP48 7 × 7 mm; Junction-to-ambient | typ 84 °C/W | 90 |
| Thermal resistance Θ | LQFP48 7 × 7 mm; Junction-to-board | typ 76 °C/W | 90 |
| Thermal resistance Θ | LQFP48 7 × 7 mm; Junction-to-case | typ 42 °C/W | 90 |
| External voltage on VREF+ pin VREF+ | Maximum: Min(VDD + 0.4, 4.0) V | min -0.3 V | 40 |
| Input voltage on FT_xx VIN | Maximum: VDD + 4.0 V; internal pull-up/pull-down resistors disabled above 4 V | min -0.3 V | 40 |
| Injected current on a FT_xx pin IINJ(PIN) | Max column states -5 / NA; positive injection not possible | max -5 mA | 40 |
| Supply voltage VDD/DDA | min 2 · max 3.6 V | 41 | |
| I/O input voltage VIN | Maximum: Min(VDD + 3.6, 5.5) V; disable internal pull-up/pull-down above VDD + 0.3 V | min -0.3 V | 41 |
| Ambient temperature TA | TA(max) applies to PD(max) | min -40 · max 85 °C | 41 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 64 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 5.7 · max 8 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 64 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 5.9 · max 8.3 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 56 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 5.1 · max 7.1 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 56 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 5.2 · max 7.1 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 48 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 4.6 · max 5.7 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 48 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 4.7 · max 6 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 32 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 3.2 · max 4.6 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 32 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 3.3 · max 4.9 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 24 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 2.5 · max 3.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 24 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 2.6 · max 3.8 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; fHCLK = fHSI bypass, 16 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 1.6 · max 2.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; fHCLK = fHSI bypass, 16 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 1.7 · max 2.9 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 64 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 4.7 · max 7.2 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 64 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 4.8 · max 7.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 56 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 4.2 · max 6.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 56 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 4.3 · max 6.7 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 48 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 3.7 · max 5.7 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 48 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 3.9 · max 6 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 32 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 2.6 · max 4.1 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 32 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 2.7 · max 4.3 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 24 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 2 · max 3.2 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; 24 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 2.1 · max 3.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; fHCLK = fHSI bypass, 16 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 1.3 · max 2.3 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 1; PLL enabled; fHCLK = fHSI bypass, 16 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 1.3 · max 2.4 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 16 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 1.3 · max 2 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 16 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 1.3 · max 2.3 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 8 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 0.7 · max 1.4 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 8 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 0.8 · max 1.5 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 2 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 0.3 · max 0.6 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 2 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 0.3 · max 0.9 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 16 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 1.1 · max 1.9 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 16 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 1.1 · max 2.1 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 8 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 0.6 · max 1.2 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 8 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 0.6 · max 1.4 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 2 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 0.2 · max 0.6 mA | 44 |
| Supply current in Run mode IDD(Run) | Range 2; PLL enabled; fHCLK = fHSI bypass, 2 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 0.3 · max 0.9 mA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 2 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 182 · max 570 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 2 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 226 · max 790 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 1 MHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 99 · max 480 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 1 MHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 132 · max 700 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 500 kHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 58 · max 430 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 500 kHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 89 · max 630 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 125 kHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 25 · max 370 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 125 kHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 56 · max 600 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fLSE bypass, 32 kHz; Flash memory; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 17 · max 330 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fLSE bypass, 32 kHz; Flash memory; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 47 · max 480 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 2 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 161 · max 550 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 2 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 191 · max 800 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 1 MHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 91 · max 470 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 1 MHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 114 · max 750 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 500 kHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 48 · max 410 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 500 kHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 81 · max 710 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 125 kHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 21 · max 360 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fHSE bypass, 125 kHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 51 · max 500 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fLSE bypass, 32 kHz; SRAM; 25°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 15 · max 310 uA | 44 |
| Supply current in Low-power run mode IDD(LPRun) | PLL disabled; fHCLK = fLSE bypass, 32 kHz; SRAM; 85°C; typ VDD = 3.0 V, max VDD = 3.6 V; all peripherals disabled | typ 37 · max 400 uA | 44 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL enabled; 64 MHz; 25°C | typ 1.4 · max 2.2 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL enabled; 64 MHz; 85°C | typ 1.5 · max 2.4 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL enabled; 56 MHz; 25°C | typ 1.3 · max 1.9 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL enabled; 56 MHz; 85°C | typ 1.4 · max 2.1 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL enabled; 48 MHz; 25°C | typ 1.2 · max 1.9 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL enabled; 48 MHz; 85°C | typ 1.2 · max 1.9 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL enabled; 32 MHz; 25°C | typ 0.9 · max 1.4 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL enabled; 32 MHz; 85°C | typ 0.9 · max 1.5 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL enabled; 24 MHz; 25°C | typ 0.7 · max 1.1 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL enabled; 24 MHz; 85°C | typ 0.8 · max 1.3 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL disabled; fHCLK = fHSE bypass, 16 MHz; 25°C | typ 0.4 · max 0.7 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 1; PLL disabled; fHCLK = fHSE bypass, 16 MHz; 85°C | typ 0.4 · max 0.8 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 2; PLL disabled; fHCLK = fHSE bypass, 16 MHz; 25°C | typ 0.3 · max 0.6 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 2; PLL disabled; fHCLK = fHSE bypass, 16 MHz; 85°C | typ 0.4 · max 0.7 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 2; PLL disabled; fHCLK = fHSE bypass, 8 MHz; 25°C | typ 0.2 · max 0.3 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 2; PLL disabled; fHCLK = fHSE bypass, 8 MHz; 85°C | typ 0.3 · max 0.6 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 2; PLL disabled; fHCLK = fHSE bypass, 2 MHz; 25°C | typ 0.1 · max 0.2 mA | 45 |
| Supply current in Sleep mode IDD(Sleep) | Flash memory enabled; all peripherals disabled; Range 2; PLL disabled; fHCLK = fHSE bypass, 2 MHz; 85°C | typ 0.2 · max 0.5 mA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash memory disabled; PLL disabled; all peripherals disabled; fHCLK = fHSE bypass, 2 MHz; 25°C | typ 43 · max 175 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash memory disabled; PLL disabled; all peripherals disabled; fHCLK = fHSE bypass, 2 MHz; 85°C | typ 77 · max 410 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash memory disabled; PLL disabled; all peripherals disabled; fHCLK = fHSE bypass, 1 MHz; 25°C | typ 29 · max 150 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash memory disabled; PLL disabled; all peripherals disabled; fHCLK = fHSE bypass, 1 MHz; 85°C | typ 60 · max 375 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash memory disabled; PLL disabled; all peripherals disabled; fHCLK = fHSE bypass, 500 kHz; 25°C | typ 23 · max 145 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash memory disabled; PLL disabled; all peripherals disabled; fHCLK = fHSE bypass, 500 kHz; 85°C | typ 52 · max 285 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash memory disabled; PLL disabled; all peripherals disabled; fHCLK = fHSE bypass, 125 kHz; 25°C | typ 16 · max 130 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash memory disabled; PLL disabled; all peripherals disabled; fHCLK = fHSE bypass, 125 kHz; 85°C | typ 46 · max 270 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash memory disabled; PLL disabled; all peripherals disabled; fHCLK = fLSE bypass, 32 kHz; 25°C | typ 13 · max 125 uA | 45 |
| Supply current in Low-power sleep mode IDD(LPSleep) | Flash memory disabled; PLL disabled; all peripherals disabled; fHCLK = fLSE bypass, 32 kHz; 85°C | typ 44 · max 260 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON; VDD = 2.4 V; 25 °C | typ 290 · max 395 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON; VDD = 2.4 V; 85 °C | typ 320 · max 540 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON; VDD = 3 V; 25 °C | typ 295 · max 415 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON; VDD = 3 V; 85 °C | typ 325 · max 580 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON; VDD = 3.6 V; 25 °C | typ 295 · max 445 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel ON; VDD = 3.6 V; 85 °C | typ 325 · max 595 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF; VDD = 2.4 V; 25 °C | typ 105 · max 145 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF; VDD = 2.4 V; 85 °C | typ 145 · max 265 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF; VDD = 3 V; 25 °C | typ 105 · max 150 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF; VDD = 3 V; 85 °C | typ 150 · max 285 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF; VDD = 3.6 V; 25 °C | typ 110 · max 150 uA | 45 |
| Supply current in Stop 0 mode IDD(Stop 0) | HSI kernel OFF; VDD = 3.6 V; 85 °C | typ 150 · max 295 uA | 45 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC disabled; VDD = 2.4 V; 25 °C | typ 3.4 · max 17 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC disabled; VDD = 2.4 V; 85 °C | typ 28 · max 130 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC disabled; VDD = 3 V; 25 °C | typ 3.6 · max 22 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC disabled; VDD = 3 V; 85 °C | typ 28 · max 140 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC disabled; VDD = 3.6 V; 25 °C | typ 3.9 · max 28 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC disabled; VDD = 3.6 V; 85 °C | typ 29 · max 155 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC enabled, clocked by LSE bypass; VDD = 2.4 V; 25 °C | typ 3.9 · max 22 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC enabled, clocked by LSE bypass; VDD = 2.4 V; 85 °C | typ 28 · max 140 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC enabled, clocked by LSE bypass; VDD = 3 V; 25 °C | typ 4.1 · max 23 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC enabled, clocked by LSE bypass; VDD = 3 V; 85 °C | typ 29 · max 155 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC enabled, clocked by LSE bypass; VDD = 3.6 V; 25 °C | typ 4.6 · max 28 uA | 46 |
| Supply current in Stop 1 mode IDD(Stop 1) | Flash memory not powered; RTC enabled, clocked by LSE bypass; VDD = 3.6 V; 85 °C | typ 29 · max 160 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled; VDD = 2.4 V; 25 °C | typ 1 · max 2.1 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled; VDD = 2.4 V; 85 °C | typ 1.8 · max 14 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled; VDD = 3.0 V; 25 °C | typ 1.2 · max 2.7 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled; VDD = 3.0 V; 85 °C | typ 2.1 · max 16 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled; VDD = 3.6 V; 25 °C | typ 1.4 · max 3 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC disabled; VDD = 3.6 V; 85 °C | typ 2.5 · max 19 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, clocked by LSI; VDD = 2.4 V; 25 °C | typ 1.3 · max 2.2 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, clocked by LSI; VDD = 2.4 V; 85 °C | typ 2.1 · max 17 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, clocked by LSI; VDD = 3.0 V; 25 °C | typ 1.7 · max 2.9 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, clocked by LSI; VDD = 3.0 V; 85 °C | typ 2.5 · max 19 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, clocked by LSI; VDD = 3.6 V; 25 °C | typ 2.1 · max 3.8 uA | 46 |
| Supply current in Standby mode IDD(Standby) | RTC enabled, clocked by LSI; VDD = 3.6 V; 85 °C | typ 3 · max 19 uA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE bypass at 32.768 kHz; VBAT = 2.4 V; 25 °C | typ 270 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE bypass at 32.768 kHz; VBAT = 2.4 V; 85 °C | typ 360 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE bypass at 32.768 kHz; VBAT = 3.0 V; 25 °C | typ 360 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE bypass at 32.768 kHz; VBAT = 3.0 V; 85 °C | typ 460 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE bypass at 32.768 kHz; VBAT = 3.6 V; 25 °C | typ 470 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE bypass at 32.768 kHz; VBAT = 3.6 V; 85 °C | typ 600 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE crystal at 32.768 kHz; VBAT = 2.4 V; 25 °C | typ 410 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE crystal at 32.768 kHz; VBAT = 2.4 V; 85 °C | typ 440 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE crystal at 32.768 kHz; VBAT = 3.0 V; 25 °C | typ 510 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE crystal at 32.768 kHz; VBAT = 3.0 V; 85 °C | typ 530 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE crystal at 32.768 kHz; VBAT = 3.6 V; 25 °C | typ 630 nA | 46 |
| Supply current in VBAT mode IDD_VBAT | RTC enabled, clocked by LSE crystal at 32.768 kHz; VBAT = 3.6 V; 85 °C | typ 770 nA | 46 |
| IOPORT Bus | IOPORT; Range 1 | typ 0.5 uA/MHz | 48 |
| IOPORT Bus | IOPORT; Range 2 | typ 0.4 uA/MHz | 48 |
| IOPORT Bus | IOPORT; Low-power run and sleep | typ 0.3 uA/MHz | 48 |
| GPIOA | IOPORT; Range 1 | typ 3.1 uA/MHz | 48 |
| GPIOA | IOPORT; Range 2 | typ 2.4 uA/MHz | 48 |
| GPIOA | IOPORT; Low-power run and sleep | typ 3 uA/MHz | 48 |
| GPIOB | IOPORT; Range 1 | typ 2.9 uA/MHz | 48 |
| GPIOB | IOPORT; Range 2 | typ 2.3 uA/MHz | 48 |
| GPIOB | IOPORT; Low-power run and sleep | typ 3 uA/MHz | 48 |
| GPIOC | IOPORT; Range 1 | typ 0.9 uA/MHz | 48 |
| GPIOC | IOPORT; Range 2 | typ 0.8 uA/MHz | 48 |
| GPIOC | IOPORT; Low-power run and sleep | typ 1 uA/MHz | 48 |
| GPIOD | IOPORT; Range 1 | typ 0.7 uA/MHz | 48 |
| GPIOD | IOPORT; Range 2 | typ 0.6 uA/MHz | 48 |
| GPIOD | IOPORT; Low-power run and sleep | typ 1 uA/MHz | 48 |
| GPIOF | IOPORT; Range 1 | typ 0.5 uA/MHz | 48 |
| GPIOF | IOPORT; Range 2 | typ 0.5 uA/MHz | 48 |
| GPIOF | IOPORT; Low-power run and sleep | typ 1 uA/MHz | 48 |
| Bus matrix | AHB; Range 1 | typ 3.2 uA/MHz | 48 |
| Bus matrix | AHB; Range 2 | typ 2.2 uA/MHz | 48 |
| Bus matrix | AHB; Low-power run and sleep | typ 2.8 uA/MHz | 48 |
| All AHB Peripherals | AHB; Range 1 | typ 9.8 uA/MHz | 48 |
| All AHB Peripherals | AHB; Range 2 | typ 8.2 uA/MHz | 48 |
| All AHB Peripherals | AHB; Low-power run and sleep | typ 8.5 uA/MHz | 48 |
| DMA1/DMAMUX | AHB; Range 1 | typ 3.4 uA/MHz | 48 |
| DMA1/DMAMUX | AHB; Range 2 | typ 2.9 uA/MHz | 48 |
| DMA1/DMAMUX | AHB; Low-power run and sleep | typ 3 uA/MHz | 48 |
| CRC | AHB; Range 1 | typ 0.5 uA/MHz | 48 |
| CRC | AHB; Range 2 | typ 0.4 uA/MHz | 48 |
| CRC | AHB; Low-power run and sleep | typ 0.5 uA/MHz | 48 |
| FLASH | AHB; Range 1 | typ 4.3 uA/MHz | 48 |
| FLASH | AHB; Range 2 | typ 3.6 uA/MHz | 48 |
| FLASH | AHB; Low-power run and sleep | typ 3.5 uA/MHz | 48 |
| All APB peripherals | APB; Range 1 | typ 23.5 uA/MHz | 48 |
| All APB peripherals | APB; Range 2 | typ 20 uA/MHz | 48 |
| All APB peripherals | APB; Low-power run and sleep | typ 20.5 uA/MHz | 48 |
| AHB to APB bridge | APB; Range 1; automatically active when at least one APB peripheral is ON | typ 0.2 uA/MHz | 48 |
| AHB to APB bridge | APB; Range 2; automatically active when at least one APB peripheral is ON | typ 0.2 uA/MHz | 48 |
| AHB to APB bridge | APB; Low-power run and sleep; automatically active when at least one APB peripheral is ON | typ 0.1 uA/MHz | 48 |
| PWR | APB; Range 1 | typ 0.4 uA/MHz | 48 |
| PWR | APB; Range 2 | typ 0.3 uA/MHz | 48 |
| PWR | APB; Low-power run and sleep | typ 0.5 uA/MHz | 48 |
| SYSCFG | APB; Range 1 | typ 0.4 uA/MHz | 48 |
| SYSCFG | APB; Range 2 | typ 0.4 uA/MHz | 48 |
| SYSCFG | APB; Low-power run and sleep | typ 0.5 uA/MHz | 48 |
| WWDG | APB; Range 1 | typ 0.2 uA/MHz | 48 |
| WWDG | APB; Range 2 | typ 0.3 uA/MHz | 48 |
| WWDG | APB; Low-power run and sleep | typ 0.5 uA/MHz | 48 |
| TIM1 | APB; Range 1 | typ 7 uA/MHz | 48 |
| TIM1 | APB; Range 2 | typ 5.9 uA/MHz | 48 |
| TIM1 | APB; Low-power run and sleep | typ 6.5 uA/MHz | 48 |
| TIM3 | APB; Range 1 | typ 3.6 uA/MHz | 48 |
| TIM3 | APB; Range 2 | typ 3.1 uA/MHz | 48 |
| TIM3 | APB; Low-power run and sleep | typ 3.5 uA/MHz | 48 |
| TIM14 | APB; Range 1 | typ 1.5 uA/MHz | 48 |
| TIM14 | APB; Range 2 | typ 1.3 uA/MHz | 48 |
| TIM14 | APB; Low-power run and sleep | typ 1.5 uA/MHz | 48 |
| TIM16 | APB; Range 1 | typ 2.3 uA/MHz | 48 |
| TIM16 | APB; Range 2 | typ 2 uA/MHz | 48 |
| TIM16 | APB; Low-power run and sleep | typ 2.5 uA/MHz | 48 |
| TIM17 | APB; Range 1 | typ 1 uA/MHz | 48 |
| TIM17 | APB; Range 2 | typ 0.8 uA/MHz | 48 |
| TIM17 | APB; Low-power run and sleep | typ 0.3 uA/MHz | 48 |
| I2C1 | APB; Range 1 | typ 3.2 uA/MHz | 48 |
| I2C1 | APB; Range 2 | typ 2.7 uA/MHz | 48 |
| I2C1 | APB; Low-power run and sleep | typ 3 uA/MHz | 48 |
| I2C2 | APB; Range 1 | typ 0.7 uA/MHz | 48 |
| I2C2 | APB; Range 2 | typ 0.6 uA/MHz | 48 |
| I2C2 | APB; Low-power run and sleep | typ 1 uA/MHz | 48 |
| SPI1 | APB; Range 1 | typ 2.2 uA/MHz | 48 |
| SPI1 | APB; Range 2 | typ 1.8 uA/MHz | 48 |
| SPI1 | APB; Low-power run and sleep | typ 2 uA/MHz | 48 |
| SPI2 | APB; Range 1 | typ 1.3 uA/MHz | 48 |
| SPI2 | APB; Range 2 | typ 1.1 uA/MHz | 48 |
| SPI2 | APB; Low-power run and sleep | typ 1.5 uA/MHz | 48 |
| USART1 | APB; Range 1 | typ 6.6 uA/MHz | 48 |
| USART1 | APB; Range 2 | typ 5.6 uA/MHz | 48 |
| USART1 | APB; Low-power run and sleep | typ 6 uA/MHz | 48 |
| USART2 | APB; Range 1 | typ 1.8 uA/MHz | 48 |
| USART2 | APB; Range 2 | typ 1.5 uA/MHz | 48 |
| USART2 | APB; Low-power run and sleep | typ 2 uA/MHz | 48 |
| ADC | APB; Range 1 | typ 1.6 uA/MHz | 48 |
| ADC | APB; Range 2 | typ 1.5 uA/MHz | 48 |
| ADC | APB; Low-power run and sleep | typ 1.5 uA/MHz | 48 |
| Wakeup time from Sleep to Run mode tWUSLEEP | Based on characterization results, not tested in production | typ 11 · max 11 CPU cycles | 49 |
| Wakeup time from Low-power sleep mode tWULPSLEEP | Transiting to Low-power-run-mode execution in Flash memory not powered in Low-power sleep mode; HCLK = HSI16 / 8 = 2 MHz | typ 11 · max 14 CPU cycles | 49 |
| Wakeup time from Stop 0 tWUSTOP0 | Transiting to Run-mode execution in Flash memory not powered in Stop 0 mode; HCLK = HSI16 = 16 MHz; Regulator in Range 1 or Range 2 | typ 5.6 · max 6 us | 49 |
| Wakeup time from Stop 0 tWUSTOP0 | Transiting to Run-mode execution in SRAM or in Flash memory powered in Stop 0 mode; HCLK = HSI16 = 16 MHz; Regulator in Range 1 or Range 2 | typ 2 · max 2.4 us | 49 |
| Wakeup time from Stop 1 tWUSTOP1 | Transiting to Run-mode execution in Flash memory not powered in Stop 1 mode; HCLK = HSI16 = 16 MHz; Regulator in Range 1 or Range 2 | typ 9 · max 11.2 us | 49 |
| Wakeup time from Stop 1 tWUSTOP1 | Transiting to Run-mode execution in SRAM or in Flash memory powered in Stop 1 mode; HCLK = HSI16 = 16 MHz; Regulator in Range 1 or Range 2 | typ 5 · max 7.5 us | 49 |
| Wakeup time from Stop 1 tWUSTOP1 | Transiting to Low-power-run-mode execution in Flash memory not powered in Stop 1 mode; HCLK = HSI16/8 = 2 MHz; Regulator in low-power mode (LPR = 1 in PWR_CR1) | typ 22 · max 25.3 us | 49 |
| Wakeup time from Stop 1 tWUSTOP1 | Transiting to Low-power-run-mode execution in SRAM or in Flash memory powered in Stop 1 mode; HCLK = HSI16 / 8 = 2 MHz; Regulator in low-power mode (LPR = 1 in PWR_CR1) | typ 18 · max 23.5 us | 49 |
| Wakeup time from Standby mode tWUSTBY | Transiting to Run mode; HCLK = HSI16 = 16 MHz; Regulator in Range 1 | typ 14.5 · max 30 us | 49 |
| Wakeup time from Low-power run mode tWULPRUN | Transiting to Run mode; HSISYS = HSI16/8 = 2 MHz; time until REGLPF flag is cleared in PWR_SR2 | typ 5 · max 7 us | 49 |
| User external clock source frequency fLSE_ext | Guaranteed by design | typ 32.768 · max 1000 kHz | 51 |
| OSC32_IN high or low time tw(LSEH), tw(LSEL) | Guaranteed by design | min 250 ns | 51 |
| Oscillator frequency fOSC_IN | min 4 · typ 8 · max 48 MHz | 51 | |
| Feedback resistor RF | typ 200 kΩ | 51 | |
| HSE current consumption IDD(HSE) | During startup, first 2/3 of startup time | max 5.5 mA | 52 |
| HSE current consumption IDD(HSE) | VDD = 3 V, Rm = 30 Ω, CL = 10 pF@8 MHz | typ 0.58 mA | 52 |
| HSE current consumption IDD(HSE) | VDD = 3 V, Rm = 45 Ω, CL = 10 pF@8 MHz | typ 0.59 mA | 52 |
| HSE current consumption IDD(HSE) | VDD = 3 V, Rm = 30 Ω, CL = 5 pF@48 MHz | typ 0.89 mA | 52 |
| HSE current consumption IDD(HSE) | VDD = 3 V, Rm = 30 Ω, CL = 10 pF@48 MHz | typ 1.14 mA | 52 |
| HSE current consumption IDD(HSE) | VDD = 3 V, Rm = 30 Ω, CL = 20 pF@48 MHz | typ 1.94 mA | 52 |
| Maximum critical crystal transconductance Gm | Startup | max 1.5 mA/V | 52 |
| Startup time tSU(HSE) | VDD is stabilized | typ 2 ms | 52 |
| LSE current consumption IDD(LSE) | LSEDRV[1:0] = 00, Low drive capability | typ 250 nA | 53 |
| LSE current consumption IDD(LSE) | LSEDRV[1:0] = 01, Medium low drive capability | typ 315 nA | 53 |
| LSE current consumption IDD(LSE) | LSEDRV[1:0] = 10, Medium high drive capability | typ 500 nA | 53 |
| LSE current consumption IDD(LSE) | LSEDRV[1:0] = 11, High drive capability | typ 630 nA | 53 |
| Maximum critical crystal gm Gmcritmax | LSEDRV[1:0] = 00, Low drive capability | max 0.5 uA/V | 53 |
| Maximum critical crystal gm Gmcritmax | LSEDRV[1:0] = 01, Medium low drive capability | max 0.75 uA/V | 53 |
| Maximum critical crystal gm Gmcritmax | LSEDRV[1:0] = 10, Medium high drive capability | max 1.7 uA/V | 53 |
| Maximum critical crystal gm Gmcritmax | LSEDRV[1:0] = 11, High drive capability | max 2.7 uA/V | 53 |
| Startup time tSU(LSE) | VDD is stabilized | typ 2 s | 53 |
| HSI16 Frequency fHSI16 | VDD=3.0 V, TA=30 °C | min 15.88 · max 16.08 MHz | 54 |
| HSI16 oscillator frequency drift over temperature ∆Temp(HSI16) | TA= 0 to 85 °C | min -1 · max 1 % | 54 |
| HSI16 oscillator frequency drift over VDD ∆VDD(HSI16) | VDD=VDD(min) to 3.6 V | min -0.1 · max 0.05 % | 54 |
| HSI16 frequency user trimming step TRIM | From code 127 to 128 | min -8 · typ -6 · max -4 % | 54 |
| HSI16 frequency user trimming step TRIM | From code 63 to 64; From code 191 to 192 | min -5.8 · typ -3.8 · max -1.8 % | 54 |
| HSI16 frequency user trimming step TRIM | For all other code increments | min 0.2 · typ 0.3 · max 0.4 % | 54 |
| Duty Cycle DHSI16 | min 45 · max 55 % | 54 | |
| HSI16 oscillator start-up time tsu(HSI16) | typ 0.8 · max 1.2 us | 54 | |
| PLL power consumption on VDD IDD(PLL) | VCO freq = 96 MHz | typ 200 · max 260 uA | 56 |
| PLL power consumption on VDD IDD(PLL) | VCO freq = 192 MHz | typ 300 · max 380 uA | 56 |
| PLL power consumption on VDD IDD(PLL) | VCO freq = 344 MHz | typ 520 · max 650 uA | 56 |
| 64-bit programming time tprog | typ 85 · max 125 us | 56 | |
| Row (32 double word) programming time tprog_row | Normal programming | typ 2.7 · max 4.6 ms | 56 |
| Row (32 double word) programming time tprog_row | Fast programming | typ 1.7 · max 2.8 ms | 56 |
| Page (2 Kbyte) programming time tprog_page | Normal programming | typ 21.8 · max 36.6 ms | 56 |
| Page (2 Kbyte) programming time tprog_page | Fast programming | typ 13.7 · max 22.4 ms | 56 |
| Page (2 Kbyte) erase time tERASE | typ 22 · max 40 ms | 56 | |
| Bank (64 Kbyte) programming time tprog_bank | Normal programming | typ 0.7 · max 1.2 s | 56 |
| Bank (64 Kbyte) programming time tprog_bank | Fast programming | typ 0.4 · max 0.7 s | 56 |
| Mass erase time tME | typ 22.1 · max 40.1 ms | 56 | |
| Average consumption from VDD IDD(FlashA) | Programming | typ 3 mA | 56 |
| Average consumption from VDD IDD(FlashA) | Page erase | typ 3 mA | 56 |
| Average consumption from VDD IDD(FlashA) | Mass erase | typ 5 mA | 56 |
| Maximum current (peak) IDD(FlashP) | Programming, 2 us peak duration | typ 7 mA | 56 |
| Maximum current (peak) IDD(FlashP) | Erase, 41 us peak duration | typ 7 mA | 56 |
| Endurance NEND | TA = -40 to +85 °C | min 1 kcycles | 56 |
| Data retention tRET | 1 kcycle at TA = 85 °C | min 15 Years | 56 |
| Electrostatic discharge voltage (human body model) VESD(HBM) | TA = +25 °C, conforming to ANSI/ESDA/JEDEC JS-001; Class 1C | max 1000 V | 58 |
| Electrostatic discharge voltage (charge device model) VESD(CDM) | TA = +25 °C, conforming to ANSI/ESDA/JEDEC JS-002; Class C2a | max 500 V | 58 |
| Injected current on pin IINJ | All except PA1, PA3, PA5, PA6, PA13, PB0, PB1, PB2, and PB8; negative injection; positive injection N/A | min -5 mA | 59 |
| Injected current on pin IINJ | PA1, PA5, PA13, PB1, PB2; negative injection 0; positive injection +5 with switchable diode activated, N/A otherwise | min 0 · max 5 mA | 59 |
| Injected current on pin IINJ | PA3, PA6, PB0; negative injection -5; positive injection +5 with switchable diode activated, N/A otherwise | min -5 · max 5 mA | 59 |
| Injected current on pin IINJ | PB8; negative injection; positive injection N/A | min 0 mA | 59 |
| Output low level voltage for an I/O pin VOL | CMOS port, |IIO| 6 mA, VDDIO1 ≥ 2.7 V | max 0.4 V | 63 |
| Output low level voltage for an I/O pin VOL | TTL port, |IIO| = 6 mA, VDDIO1 ≥ 2.7 V | max 0.4 V | 63 |
| Output high level voltage for an I/O pin VOH | TTL port, |IIO| = 6 mA, VDDIO1 ≥ 2.7 V | min 2.4 V | 63 |
| Output low level voltage for an I/O pin VOL | All I/Os, |IIO| = 15 mA, VDDIO1 ≥ 2.7 V | max 1.3 V | 63 |
| Output low level voltage for an I/O pin VOL | |IIO| = 3 mA | max 0.4 V | 63 |
| Output low level voltage for an FT I/O pin in FM+ mode (FT I/O with _f option) VOLFM+ | |IIO| = 20 mA, VDDIO1 ≥ 2.7 V | max 0.4 V | 63 |
| Output low level voltage for an FT I/O pin in FM+ mode (FT I/O with _f option) VOLFM+ | |IIO| = 9 mA | max 0.4 V | 63 |
| Maximum frequency Fmax | Speed 00, C=50 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 2 MHz | 63 |
| Maximum frequency Fmax | Speed 00, C=50 pF, 2.0 V ≤ VDDIO1 ≤ 2.7 V | max 0.35 MHz | 63 |
| Maximum frequency Fmax | Speed 00, C=10 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 3 MHz | 63 |
| Maximum frequency Fmax | Speed 00, C=10 pF, 2.0 V ≤ VDDIO1 ≤ 2.7 V | max 0.45 MHz | 63 |
| Output rise and fall time Tr/Tf | Speed 00, C=50 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 100 ns | 63 |
| Output rise and fall time Tr/Tf | Speed 00, C=50 pF, 2.0 V ≤ VDDIO1 ≤ 2.7 V | max 225 ns | 63 |
| Output rise and fall time Tr/Tf | Speed 00, C=10 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 75 ns | 63 |
| Output rise and fall time Tr/Tf | Speed 00, C=10 pF, 2.0 V ≤ VDDIO1 ≤ 2.7 V | max 150 ns | 63 |
| Maximum frequency Fmax | Speed 01, C=50 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 10 MHz | 64 |
| Maximum frequency Fmax | Speed 01, C=50 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 2 MHz | 64 |
| Maximum frequency Fmax | Speed 01, C=10 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 15 MHz | 64 |
| Maximum frequency Fmax | Speed 01, C=10 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 2.5 MHz | 64 |
| Output rise and fall time Tr/Tf | Speed 01, C=50 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 30 ns | 64 |
| Output rise and fall time Tr/Tf | Speed 01, C=50 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 60 ns | 64 |
| Output rise and fall time Tr/Tf | Speed 01, C=10 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 15 ns | 64 |
| Output rise and fall time Tr/Tf | Speed 01, C=10 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 30 ns | 64 |
| Maximum frequency Fmax | Speed 10, C=50 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 30 MHz | 64 |
| Maximum frequency Fmax | Speed 10, C=50 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 15 MHz | 64 |
| Maximum frequency Fmax | Speed 10, C=10 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 60 MHz | 64 |
| Maximum frequency Fmax | Speed 10, C=10 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 30 MHz | 64 |
| Output rise and fall time Tr/Tf | Speed 10, C=50 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 11 ns | 64 |
| Output rise and fall time Tr/Tf | Speed 10, C=50 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 22 ns | 64 |
| Output rise and fall time Tr/Tf | Speed 10, C=10 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 4 ns | 64 |
| Output rise and fall time Tr/Tf | Speed 10, C=10 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 8 ns | 64 |
| Maximum frequency Fmax | Speed 11, C=30 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 60 MHz | 64 |
| Maximum frequency Fmax | Speed 11, C=30 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 30 MHz | 64 |
| Maximum frequency Fmax | Speed 11, C=10 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V; I/O capability, system frequency limited to 64 MHz | max 80 MHz | 64 |
| Maximum frequency Fmax | Speed 11, C=10 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 40 MHz | 64 |
| Output rise and fall time Tr/Tf | Speed 11, C=30 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 5.5 ns | 64 |
| Output rise and fall time Tr/Tf | Speed 11, C=30 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 11 ns | 64 |
| Output rise and fall time Tr/Tf | Speed 11, C=10 pF, 2.7 V ≤ VDDIO1 ≤ 3.6 V | max 2.5 ns | 64 |
| Output rise and fall time Tr/Tf | Speed 11, C=10 pF, 1.6 V ≤ VDDIO1 ≤ 2.7 V | max 5 ns | 64 |
| Maximum frequency Fmax | Fm+, C=50 pF, 1.6 V ≤ VDDIO1 ≤ 3.6 V | max 1 MHz | 64 |
| Output fall time Tf | Fm+, C=50 pF, 1.6 V ≤ VDDIO1 ≤ 3.6 V; measured between 70% and 30% | max 5 ns | 64 |
| NRST Schmitt trigger voltage hysteresis Vhys(NRST) | typ 200 mV | 65 | |
| Weak pull-up equivalent resistor RPU | VIN = VSS | min 25 · typ 40 · max 55 kΩ | 65 |
| NRST input filtered pulse VF(NRST) | max 70 ns | 65 | |
| NRST input not filtered pulse VNF(NRST) | 2.0 V ≤ VDD ≤ 3.6 V | min 350 ns | 65 |
| Supply voltage VDD | Minimum VDD(min) | max 3.6 V | 66 |
| Booster startup time tSU(BOOST) | max 240 us | 66 | |
| Booster consumption for VDD ≤ 2.7 V | VDD ≤ 2.7 V; unit not printed | max 500 | 66 |
| Booster consumption for 2.7 V ≤ VDD ≤ 3.6 V | 2.7 V ≤ VDD ≤ 3.6 V; unit not printed | max 900 | 66 |
| Analog supply voltage VDDA | min 2 · max 3.6 V | 66 | |
| Positive reference voltage VREF+ | Maximum VDDA | min 2 V | 66 |
| ADC clock frequency fADC | Range 1 | min 0.14 · max 35 MHz | 66 |
| ADC clock frequency fADC | Range 2 | min 0.14 · max 16 MHz | 66 |
| ADC consumption from VREF+ IDDV(ADC) | fs = 2.5 MSps | typ 65 uA | 68 |
| ADC consumption from VREF+ IDDV(ADC) | fs = 1 MSps | typ 26 uA | 68 |
| ADC consumption from VREF+ IDDV(ADC) | fs = 10 kSps | typ 0.26 uA | 68 |
| Max. RAIN RAIN | 12 bits; sampling cycle 1.5 at 35 MHz; sampling time 43 ns | max 50 Ω | 68 |
| Max. RAIN RAIN | 12 bits; sampling cycle 3.5 at 35 MHz; sampling time 100 ns | max 680 Ω | 68 |
| Max. RAIN RAIN | 12 bits; sampling cycle 7.5 at 35 MHz; sampling time 214 ns | max 2200 Ω | 68 |
| Max. RAIN RAIN | 12 bits; sampling cycle 12.5 at 35 MHz; sampling time 357 ns | max 4700 Ω | 68 |
| Max. RAIN RAIN | 12 bits; sampling cycle 19.5 at 35 MHz; sampling time 557 ns | max 8200 Ω | 68 |
| Max. RAIN RAIN | 12 bits; sampling cycle 39.5 at 35 MHz; sampling time 1129 ns | max 15000 Ω | 68 |
| Max. RAIN RAIN | 12 bits; sampling cycle 79.5 at 35 MHz; sampling time 2271 ns | max 33000 Ω | 68 |
| Max. RAIN RAIN | 12 bits; sampling cycle 160.5 at 35 MHz; sampling time 4586 ns | max 50000 Ω | 68 |
| Max. RAIN RAIN | 10 bits; sampling cycle 1.5 at 35 MHz; sampling time 43 ns | max 68 Ω | 68 |
| Max. RAIN RAIN | 10 bits; sampling cycle 3.5 at 35 MHz; sampling time 100 ns | max 820 Ω | 68 |
| Max. RAIN RAIN | 10 bits; sampling cycle 7.5 at 35 MHz; sampling time 214 ns | max 3300 Ω | 68 |
| Max. RAIN RAIN | 10 bits; sampling cycle 12.5 at 35 MHz; sampling time 357 ns | max 5600 Ω | 68 |
| Max. RAIN RAIN | 10 bits; sampling cycle 19.5 at 35 MHz; sampling time 557 ns | max 10000 Ω | 68 |
| Max. RAIN RAIN | 10 bits; sampling cycle 39.5 at 35 MHz; sampling time 1129 ns | max 22000 Ω | 68 |
| Max. RAIN RAIN | 10 bits; sampling cycle 79.5 at 35 MHz; sampling time 2271 ns | max 39000 Ω | 68 |
| Max. RAIN RAIN | 10 bits; sampling cycle 160.5 at 35 MHz; sampling time 4586 ns | max 50000 Ω | 68 |
| Max. RAIN RAIN | 8 bits; sampling cycle 1.5 at 35 MHz; sampling time 43 ns | max 82 Ω | 68 |
| Max. RAIN RAIN | 8 bits; sampling cycle 3.5 at 35 MHz; sampling time 100 ns | max 1500 Ω | 68 |
| Max. RAIN RAIN | 8 bits; sampling cycle 7.5 at 35 MHz; sampling time 214 ns | max 3900 Ω | 68 |
| Max. RAIN RAIN | 8 bits; sampling cycle 12.5 at 35 MHz; sampling time 357 ns | max 6800 Ω | 68 |
| Max. RAIN RAIN | 8 bits; sampling cycle 19.5 at 35 MHz; sampling time 557 ns | max 12000 Ω | 68 |
| Max. RAIN RAIN | 8 bits; sampling cycle 39.5 at 35 MHz; sampling time 1129 ns | max 27000 Ω | 68 |
| Max. RAIN RAIN | 8 bits; sampling cycle 79.5 at 35 MHz; sampling time 2271 ns | max 50000 Ω | 68 |
| Max. RAIN RAIN | 8 bits; sampling cycle 160.5 at 35 MHz; sampling time 4586 ns | max 50000 Ω | 68 |

tomrodinger/servomotor
Open-source NEMA-17 integrated servomotor (motor + closed-loop driver + controller + encoder). RS-485, Python/Arduino libraries, MCP server for AI control. Hardware, firmware and software.


wallComputer/PiZumo_Robot
Git Folder to share hardware and software files for PiZumo Robot.

Wh1teRabbitHU/ER-TFT1.69-1_STM32-Driver
STM32 Driver for the following module: https://www.buydisplay.com/1-69-inch-color-280x240-round-rectangle-ips-tft-lcd-display-panel-st7789



stephaneamans/app-home_automation
The general principle is based on a centralised ECU (Raspbery Pi) with an optional coprpocessor (STM32) used to manage low speed IO.

tomrodinger/servomotor
Open-source NEMA-17 integrated servomotor (motor + closed-loop driver + controller + encoder). RS-485, Python/Arduino libraries, MCP server for AI control. Hardware, firmware and software.
Yes. The symbol is MCU_ST_STM32G0:STM32G030C8Tx and the footprint Package_QFP:LQFP-48_7x7mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
LQFP-48(7x7), with 48 pins. Its footprint is drawn on this page.
STMicroelectronics publishes it: the Datasheet link on this page opens it.
JLCPCB lists it as part C529329, with 25,131 in stock; the sellers' links on this page open their listings.
Parts like it in the library: the STM32F103C8T6 by STMicroelectronics, the STM32G070CBT6 by STMicroelectronics, the GD32F303CCT6 by GigaDevice and the GD32F103C8T6 by GigaDevice. Check their datasheets: a part that fits the footprint may still differ in its ratings.
15 boards in 9 repositories on GitHub; the most starred are listed on this page, with their KiCad files.