2 layers
Boards using the BPW34
47 boardsBoards in 36 GitHub repositories, designed in KiCad, that use the BPW34 by Vishay Intertechnology (-40℃~+100℃ 215mW 2nA 430nm~1100nm 60V 900nm ±65° 插件,P=5.1mm Photodiodes ROHS). See how each wires it, with its parts, size, README and files; the BPW34’s symbol, footprint and pinout are on its own page.
- 2 layers82.1 × 82.1 mm
Uncut Gem
QuantumVillage/UncutGem
A prototype Full Stack fully Open Source NV Center Diamond Magnetometer
207 parts210AGPL-3.0 - 2 layers90 × 55 mm
SemiconductorRadioactivityDetector
RobertGawron/SemiconductorRadioactivityDetector
Nuclear radiation sensor with photodiode as a detector. Photodiode doesn't require high voltages as GM tubes do. Smaller size makes better resolution. Side effect is electronic must be more sensitive.
43 parts29GPL-3.0 - 2 layers76.5 × 55.7 mm
Vive sensors smd 4x4panel
Roboy/HTC_Vive_Sensors
Schematics and PCB designs for our custom Vive sensors based on a quad op-amp chip rather than discrete transistors.
614 parts23 - 2 layers97.2 × 55.9 mm
Mjs pcb
meetjestad/mjs_pcb
This repository contains various versions of the sensor station PCB used by Meetjestad.
83 parts6 - 2 layers49.5 × 42.5 mm
- 2 layers100 × 100 mm
- 2 layers37 × 36 mm
- 2 layers
Gluco calibration
Martins-Lucaas/IB2-project
Destinado a criação de um equipamento médico funcional para leitura da saturação de glicose do corpo
28 parts1 - 2 layers80 × 50 mm
Blitzortung AS3935
patkan/lightning-detector
Lightning Detector ethernet sensor node and server based on AS3935 - this project is discontinued
81 parts1GPL-2.0 - 4 layers49.6 × 40 mm
Fsoc rx
SharbelMarshi/txrx-optical-communication-kicad
A Free-Space Optical Communication link KiCad project
62 parts1 - 2 layers68.6 × 31.8 mm
- 2 layers65.5 × 43.5 mm
Receiver board
abhictrl/IEEE-HOPE-FSO
A laser-based audio communication link for the Howard University IEEE H.O.P.E. Project.
15 partsMIT - 2 layers72.1 × 51.3 mm
- 2 layers60 × 45 mm
Photodiode TIA ESP32
buffer-cloud/Photodiode-TIA-ESP32
Low-noise photodiode transimpedance amplifier with ESP32 wireless acquisition and Python-based signal analysis.
42 parts - 2 layers58.6 × 65.9 mm
FSFO
filezz/Free-Space-Optics-Audio-transmission-system
A hardware project that successfully transmits an analog audio signal over a laser beam using Amplitude Modulation (AM).
32 parts - 2 layers66 × 21.7 mm
Detector de particulas (FISICA III)
hernansilva02/fotodiodo-project
Proyecto académico/open-hardware para el diseño, simulación y fabricación de un detector basado en fotodiodo PIN con amplificador transimpedancia (TIA).
22 parts - 4 layers
- 4 layers74 × 146 mm
- 2 layers151 × 94 mm
LED matrix Error-2026
Jed0vcela/LED-matrix-Error-2026
Kapesní zařízení s LED maticí 32×16, postavené na Raspberry Pi Pico (RP2040) s MicroPythonem. Samotné zařízení nabízí přes 20 vestavěných her a pomůcek; víc zařízení lze propojit řetězcem po UART pro hry pro dva hráče a…
639 parts - 2 layers86 × 42.5 mm
Ppg circuit
kdbell4/PPG-Vitals-Monitor
A finger-clip vitals monitor built from scratch. Monitors standard vitals (heart rate, blood oxygen).
19 parts - 2 layers78 × 79.5 mm
Pulse oximeter
khomyakova228-cell/pulse-oximeter
Домашнее задание по курсу «САПР электронных средств» «Проект печатного узла пульсоксиметра в KiCad: оформление по ГОСТ, библиотека компонентов, автоматизация проверки и выпуска» Обозначение документа: БИГЕ.149980.001 Э3
93 parts - 2 layers91 × 34.3 mm
Scheme
n0ll0/skeemitehnika-projekt-2025
This repository contains the project files for the Skeemitehnika G11 course project "Arduino Nano digisisendi laiendus" & at TTÜ.
26 parts - 2 layers68.3 × 94.9 mm
Laser Gate
purvanyaTyagi/Laser-Gate
This repository contains the firmware and hardware design files for a laser gate detection system.
40 parts