4 layers156.5 × 85.4 mm
P2 Kevinbot Board
meowmeowahr/KevinbotV3-KiCAD
Kevinbot Core - Parallax Propeller 2 Robot Controller
166 parts7CERN-OHL-S-2.0
Boards using the PCA9685BS
30 boardsBoards in 24 GitHub repositories, designed in KiCad, that use the PCA9685BS by NXP Semiconductors (QFN-28-EP(6x6) LED Drivers ROHS). See how each wires it, with its parts, size, README and files; the PCA9685BS’s symbol, footprint and pinout are on its own page.
- 2 layers134.4 × 106.7 mm
Led controller
MbFredys/PCB-LEDs-Controller
LED-controller PCB design exercise focused on PWM control, power distribution, and hardware documentation.
42 parts6 - 2 layers100 × 75 mm
Display
DLaxV-Community-Projects-Hub/Open-Shot-Clock
Build your own DIY Shot Clock
209 parts5CERN-OHL-P-2.0 - 4 layers132.5 × 105 mm
HEXCORE PCB Design v0
JoshCrouch/HEXCORE
HEXCORE is a Hexapod-type robot that includes both a custom remote as well as vision system making use of 2.4GHz RF and WiFi respectively.
160 parts3 - 6 layers100 × 37 mm
PickleRick
icl-rocketry/Ricardo-PickleRick
A more compact Ricardo classic featuring a new sensor array, 4 pyro channels and 4 servo channels. Includes Ricardo bus plug too.
223 parts2MIT - 4 layers40 × 100 mm
NNCpro
PlanAndBuild/NoNameComputer-2.0
The NoNameComputer 2.0 AKA NNCpro is being designed for mid-high power rockets and other flying vehicle. It will be equipped with various sensors like barometers, IMUs, magnetometer, current sensing etc.
263 parts2 - 4 layers219 × 178 mm
- 2 layers71.8 × 48.5 mm
JOLT V1
GoTouchGra55/J.O.L.T
12 degrees of freedom, 1 custom devboard, and 0 off-the-shelf solutions. JOLT is a quadruped robot built entirely from scratch.
73 parts1MIT - 4 layers40 × 46 mm
MtN1 Draft 1
Momentum-Devices/MtN1-Hardware
The hardware design files for the robotics motion expansion board, Motion-1 (MtN1).
74 parts1CERN-OHL-W-2.0 - 2 layers142.8 × 72.3 mm
Glove receiver board
Aaryaaaaaaa/sEMG_RECEIVER_BOARD
This is a 2-layer PCB for the receiver node of a wireless sEMG rehabilitation glove system, which receives gesture commands over ESP-NOW and drives three servos to move the glove's fingers accordingly.
22 parts - 4 layers76.2 × 82.6 mm
- 4 layers58.5 × 56.7 mm
- 6 layers225.3 × 53.3 mm
- 4 layers
Titanrio
ggarciabaez/titanrio
A RoboRIO-Inspired Expansion board for Robotics. Mostly for funsies + learning.
83 parts - 2 layers
Robot Arm PCB
JoshAyersSBT/Robot_Arm_PCB
This document consolidates the power architecture, wiring, BOM additions, and system diagram for an ESP32-based robot arm controller using:
26 parts - 4 layers100 × 56 mm
- 2 layers160 × 110 mm
Lipo Discharger
Lnotti/5-Channel-High-Current-Li-po-Discharger
A PCB designed to discharge 6S LiHV battery packs to storage voltage (3.8V per cell / 22.8V total) across up to 5 independent channels simultaneously.
122 parts - 2 layers49.5 × 32.4 mm
- 2 layers280 × 110 mm
PCB Piano v1.1
ninjatill/PCB-Capacitive-Touch-Synth
A Raspberry Pi-based synthesizer with capacitive touch keys directly on a PCB.
284 parts - 4 layers93.5 × 94.5 mm
RC Buggy
TheFlocke/rc-buggy
Autonomous rover with BLE control and robotic arm, built for a DLR high school competition.
162 partsGPL-3.0 - 2 layers116.8 × 116.8 mm
Bentoboard
torbers/bentoboard
as many ready-to-use electronics as i could fit on a 4"x4" PCB.
381 parts - 4 layers50 × 50 mm
HadesMicro
pms67/HadesFCS
Complete flight control system designed from scratch. Hardware designed with KiCad.
91 parts1kBSD-3-Clause - 2 layers58.6 × 67.4 mm
Flight controller
UoM-Robotics-Society/ROV-project
Software, mechanical design and hardware for ROV
29 parts14 - 4 layers152.5 × 112.5 mm
HEXCORE PCB Design v1
JoshCrouch/HEXCORE
HEXCORE is a Hexapod-type robot that includes both a custom remote as well as vision system making use of 2.4GHz RF and WiFi respectively.
159 parts3