

Pump board
Design file for SMBR hardware modules in KiCAD.
- Size
- 90 × 100 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 204
- Nets
- 128
- Pads
- 685
- Tracks, vias
- 1,213, 675
- Pours
- 36
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 20 Aug 2024
- Updated
- 30 Apr 2026
Overview
Pump board is an open-source printed circuit board by TrendBit, from the TrendBit/SMBR-hardware repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 90 × 100 mm with 204 parts on 128 nets, routed with 1,213 tracks and 675 vias.
It is built around the RP2040, SN65HVD230D and DRV8870DDA, with the ADS1115IDGS, W25Q128JVSIQ and SRV05-4 among its other parts. Its parts include 59 capacitors, 57 resistors, 17 diodes, 15 ICs and 13 connectors. It belongs with the RP2040 boards of this library.
Main components
12RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)SN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversDRV8870DDA
SO-8-40℃~+125℃ 1 3.6A 565mΩ 6.5V~45V 6.5V~45V Bipolar Driver Overcurrent Protection、Short-Circuit Protection、Over temperature protection、Under-voltage lockout、Overvoltage Protection、Built-in charge pump、Power-on reset、Dead-time / shoot-through protection Yes SO-8 Stepper Motor Driver ROHSTexas InstrumentsStepper Motor DriverADS1115IDGS
MSOP10Ultra-Small, Low-Power, 4 Channels 16-Bit Analog-to-Digital Converter with Internal ReferenceTexas InstrumentsUncategorisedW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHSRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAT24C256N
DIP-8-40℃~+85℃ 1,000,000 cycles 1.8V~5.5V 100 Years 1MHz 256Kbit 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C DIP-8 EEPROM ROHSHGSEMIEEPROMSN74LVC1G14DBV
SOT-23-5-40℃~+85℃ 1 1 1.16V~3.33V 1.65V~5.5V 10uA 2.3V 32mA 32mA 390mV~1.87V 550mV 6.5ns@2.5V,50pF 74LVC Schmitt trigger 电源关断保护、噪声抑制功能 SOT-23-5 Inverters ROHSTexas InstrumentsInvertersSN74LVC1T45DBV
SOT-23-6-40℃~+85℃ 1 1 1.65V~5.5V 1.65V~5.5V 420Mbps Bidirectional Tri-State SOT-23-6 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level ShiftersSS34
SMA(DO-214AC)-55℃~+125℃ 3A 40V 500uA@40V 550mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky DiodesAO4435
SOP-8-55℃~+150℃ 1 P-Channel 1.175nF 12A 15mΩ@10V 18nC 190pF 195pF 2.5W 30V 3V SOP-8 MOSFETs ROHSUMWMOSFETs
README
README.mdSMBR - Hardware
This repository contains the documentation for all hardware modules that make up or can be connected to the Smart Modular BioReactor. All designs were made in KiCAD.
General module specification is to which modules should adhere as much as possible is in Specification.md
General system design
All the main modules are built on a similar basis. These are the RP2040 microcontroller, CANBus and development resources (SWD, UART, etc). The individual modules, in turn, add components to this base that correspond to their specific application. For example, in the case of the Control board, this includes motor drivers or electronics that control and monitor fans. The modules communicate with each other via the CAN bus, where a custom protocol is used.
Modules
Interface board
Extension for RPi 4 which adds capabilities for communication and power inputs. Board serves as hub for CAN bus connection to other modules. Modules can be connected via 3 IDC cables or stacking connector on top. Board is connected to RPi via 40 pin connector. Via this connector is Rpi power and communicate with CAN bus transceiver via SPI. I2C can be used to read on board ADC which read board input voltage, current. This board also supplies 5V rail for Rpi and rest of the system. PoE module can be mounted to the board and PoE lines will be passed from RPi header.
Control board
Board responsible for main control function of SMPBR. Can be used to control illumination intensity. Drives peltier element which influence temperature of algae in bottle. Controls Aerator, Peristaltic pump, Mixer and heat control fans on device. Reads temperature of heater plate and LED panel. Can be used as additional CAN bus HUB. Is designed to be stacked on top of Interface module, as third layer of sandwich RPi-Interface-Control.
Sensor board
Module performing most of the basic measurements related to experiment. Consists of three boards which can be connected together around sampling cuvette. Sample is pumped into cuvette and after adaptation the measurements can start. For OJIP measurement sample is saturated with high power 10W Green LED and resulting value is measured with adaptive gain IR energy sensor. Another measurement is optical density which can be measured at 6 defined wavelengths. Board also measures temperature in bottle via two contact-less thermometers (thermopiles).
Illumination board - Basic RGBW
SMPBR illumination panel with 4 channels. Channels can be controlled individually from control module. Each module has own power limit based on on board sense resistor. Board has integrated thermistor in order to limit heat dissipation which could influence the experiment.
This board has four basic colors:
- Red 625nm 4.8W
- Green 520nm 5.8W
- Blue 465nm 5.8W
- White (Warm) 2700K 6.1W
Motor filter shield for peristaltic pump
Small PCB directly soldered to motor terminals of Peristaltic pump motor. It acts as a low pass filter reducing EMI. However, it can also be soldered directly to the motor chassis, further improving EMC. It simplifies motor connection by allowing the motor to be connected via a connector on the board.
Motor filter shield for air pump
Small PCB directly soldered to motor terminals of air pump motor. It acts as a low pass filter reducing EMI. However, it can also be soldered directly to the motor chassis, further improving EMC. It simplifies motor connection by allowing the motor to be connected via a connector on the board.
[WIP] Pump board
Board for expansion pump module, which is used to control additional peristaltic pumps. To this board up to 4 peristaltic pumps can be connected a controlled. Module can be connected to SMPBR reactor via expansion port. Multiple of those modules can be connected to one bio-reactor and can be chained bia expansion ports. Module also have external power, because when more modules will be connected to expansion port, main adapter can be overloaded. External power input is prioritized over power from extension cable.
Sata Expansion port
Fluorometer LED
Parts
204| Qty | Value | Footprint | References |
|---|---|---|---|
| 29 | 100nF | Capacitor_SMD:C_0603_1608Metric | C401, C403, C404, C405, C410, C411, C412, C413, C414, C415, C1201, C1202, C1203, C1204, C1301, C1603 +13 |
| 20 | 120R@100MHz | Inductor_SMD:L_0603_1608Metric | FB401, FB501, FB502, FB503, FB601, FB701, FB702, FB703, FB704, FB705, FB801, FB802, FB803, FB804, FB1001, FB1101 +4 |
| 17 | 1k | Resistor_SMD:R_0603_1608Metric | R404, R405, R413, R416, R419, R701, R702, R803, R804, R805, R807, R808, R810, R1301, R1606, R1609 +1 |
| 15 | 1uF | Capacitor_SMD:C_0603_1608Metric | C402, C408, C409, C416, C418, C508, C509, C701, C703, C803, C805, C808, C810, C813, C815 |
| 9 | 270R | Resistor_SMD:R_0603_1608Metric | R403, R408, R410, R411, R412, R423, R424, R604, R605 |
| 8 | 10uF/25V | Capacitor_SMD:CP_Elec_4x5.4 | C502, C504, C507, C510, C705, C807, C812, C817 |
| 7 | 10k | Resistor_SMD:R_0603_1608Metric | R407, R409, R420, R502, R503, R505, R1201 |
| 6 | 22R | Resistor_SMD:R_0603_1608Metric | R414, R415, R417, R418, R421, R422 |
| 6 | M3 | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H801, H802, H803, H804, H805 |
| 5 | 100k | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R501 |
| 5 | 10nF | Capacitor_SMD:C_0603_1608Metric | C704, C801, C806, C811, C816 |
| 5 | 5.1k | Resistor_SMD:R_0603_1608Metric | R401, R402, R602, R603, R1601 |
| 4 | 100mR/0.5W | Resistor_SMD:R_1210_3225Metric | R703, R806, R809, R812 |
| 4 | DF3A-03P-2DSA | TCY_connectors:Hirose_DF3A-03P-2DSA_1x03_P2.00mm_Vertical | J701, J802, J803, J804 |
| 4 | DRV8870DDA | Package_SO:Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalVias | U701, U802, U803, U804 |
| 4 | LED | TCY_smd_leds:LED_LiteOn_LTST_S270_0603_Side | D406, D407, D408, D409 |
| 4 | RED | LED_SMD:LED_0603_1608Metric | D401, D402, D403, D602 |
| 3 | SS34 | Diode_SMD:D_SMA | D501, D504, D505 |
| 2 | 0R | Resistor_SMD:R_0603_1608Metric | R406, R601 |
| 2 | 10pF | Capacitor_SMD:C_0603_1608Metric | C406, C407 |
| 2 | 60R | Resistor_SMD:R_1206_3216Metric | R801, R802 |
| 2 | AO4435 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | Q501, Q502 |
| 2 | BM03B-SRSS-TB | Connector_JST:JST_SH_BM03B-SRSS-TB_1x03-1MP_P1.00mm_Vertical | J601, J604 |
| 2 | LOGO | LOGO | G***, G*** |
| 2 | Pin_header_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J603, J605 |
| 2 | SATA07-250B | TCY_connectors:HYC_HYCW02-SATA07-250B_Horizontal_THT | J1, J801 |
| 2 | SRV05-4 | Package_TO_SOT_SMD:SOT-23-6 | U601, U602 |
| 2 | TS-1187A-B-A-B | Button_Switch_SMD:SW_SPST_TL3342 | SW401, SW402 |
| 1 | 10k, 3950b | Inductor_SMD:L_0603_1608Metric | TH1601 |
| 1 | 12MHz | Crystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | Y401 |
| 1 | 2A | Fuse:Fuse_1206_3216Metric | F501 |
| 1 | ADS1115IDGS | Package_SO:TSSOP-10_3x3mm_P0.5mm | U1301 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U501 |
| 1 | ARM_SWD_10 | Connector:Tag-Connect_TC2050-IDC-NL_2x05_P1.27mm_Vertical_with_bottom_clip | J606 |
| 1 | AT24C256 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U401 |
| 1 | B5817W | Diode_SMD:D_SOD-123 | D601 |
| 1 | DC-044A-A200 | TCY_connectors:Barrel_Jack_DC-044A-A250 | J501 |
| 1 | DS-01R | Button_Switch_THT:SW_DIP_SPSTx01_Slide_9.78x4.72mm_W7.62mm_P2.54mm | SW403 |
| 1 | GREEN | LED_SMD:LED_0603_1608Metric | D405 |
| 1 | MM5Z5V1 | Diode_SMD:D_SOD-523 | D502 |
| 1 | PSM712-LF-T7 | Package_TO_SOT_SMD:SOT-23 | D801 |
| 1 | REF3033 | Package_TO_SOT_SMD:SOT-23 | U403 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U404 |
| 1 | SMBJ13CA | Diode_SMD:D_SMB | D503 |
| 1 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U801 |
| 1 | SN74LVC1G14DBV | Package_TO_SOT_SMD:SOT-23-5 | U1202 |
| 1 | SN74LVC1T45DBV | Package_TO_SOT_SMD:SOT-23-6 | U1203 |
| 1 | TC-6615-9.5-260G | Button_Switch_THT:SW_Tactile_SPST_Angled_PTS645Vx58-2LFS | SW1201 |
| 1 | U263-163N-4BLS1735 | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J602 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U405 |
| 1 | WS2812B | TCY_smd_leds:WS2812B_2.0x4.0mm_Side_view | D404 |
The 198 most common of 204 parts.
More from TrendBit/SMBR-hardware
12- 4 layers140 × 70 mm

- 4 layers56 × 85 mm

- 2 layers65 × 56 mm

Interface board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
133 partsGPL-3.0 - 2 layers80 × 100 mm

Illumination board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
103 partsGPL-3.0 - 2 layers80 × 100 mm

Illumination board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
91 partsGPL-3.0 - 2 layers80 × 100 mm

Illumination board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
91 partsGPL-3.0 - 2 layers97 × 100 mm

- 2 layers80 × 100 mm

Illumination board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
67 partsGPL-3.0 - 2 layers80 × 100 mm

Illumination board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
15 partsGPL-3.0 - 2 layers24 × 25.5 mm

Motor shield peristaltic
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
15 partsGPL-3.0 - 2 layers20.1 × 22 mm

Motor shield airpump
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
14 partsGPL-3.0 - 2 layers20.3 × 22.5 mm

Similar boards
- 4 layers85 × 56 mm

WLKJ2025011CAR MOTOR V1.2
TUO4742/SeedlingRobot
Full-stack ROS2 automatic seedling clamping robot covering mechanical, hardware, STM32/FreeRTOS and motion control.
96 parts - 2 layers12 × 10 mm

- 4 layers88.1 × 59.4 mm

Chromapi motherboard v1
Mowibox/chromapi_motherboard
Raspberry Pi control HAT dedicated to the quadruped robot Chromapi.
139 parts2Apache-2.0 - 4 layers222 × 100 mm

HydroScan V1
paulmartinezcuenta/Proyecto_finales_mecatronica_ITLA
Monorepo for two mechatronics projects sharing a panelized PCB: HydroScan (autonomous IoT maritime buoy with LTE, GPS, and solar power) and AUTOAMBU (automated medical respirator prototype with DC control and USB fast…
156 parts1 - 2 layers45 × 55 mm

- 2 layers70 × 65 mm

- 2 layers33.7 × 36.6 mm

HexyMicSMD
AlexJMcIntyre/HexyHexyMic
If you're here, there's a good chance you've picked up one of my HexyHexyMic Hexpansions. I hope I got the chance to say hello! If not, you can find me on Mastodon: @GlitchEngine@mastodon.social.
11 parts5 - 2 layers102.4 × 77.4 mm

Questions
How big is the Pump board PCB?
It measures 90 × 100 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Pump board use?
204 parts, built around the RP2040, SN65HVD230D, DRV8870DDA and ADS1115IDGS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pump board KiCad files?
From the TrendBit/SMBR-hardware repository on GitHub, at the commit this page was made from: the board is pump_board/pcb/pump_board.kicad_pcb and its schematic control_board/MCU.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pump board design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).